Flight Display Systems FD320LIFT-LP Manual de usuario

Rev:

Revision Date:

08/27/2012

Page 1 of 22

MAN – FD320LIFT-LP Ver HD

FD320LIFT-LP Ver HD

Installation and Operation Manual

32” High-Definition LCD with Low-Profile Motorized Lift

Manufactured by MILIC, LLC with marketing support from Flight Display Systems.

This product does not have FAA PMA approval.

TECHNICAL SUPPORT

+1 (678) 867-6717, or

www.FlightDisplay.com

All manuals and user guides at all-guides.com

all-guides.com

Rev:

Revision Date:

08/27/2012

Page 2 of 22

MAN – FD320LIFT-LP Ver HD

FD320LIFT-LP Ver HD

32" High-Definition LCD with Low-Profile Motorized Lift

Flight Display Systems

1765 Grassland Parkway

Alpharetta, GA 30004

+1 (678) 867-6717 Phone

+1 (678) 867-6742 Fax

sales@flightdisplay.com

www.flightdisplay.com

For the most current copy of all product manuals, please visit our website at

www.flightdisplay.com

For more product support information, please visit the following link at

http://support.flightdisplay.com/

All manuals and user guides at all-guides.com

Rev:

Revision Date:

08/27/2012

Page 3 of 22

MAN – FD320LIFT-LP Ver HD

Table of Contents

General Information......................................................................................................................4

1. Front View..........................................................................................................................4

2. Additional Information....................................................................................................4

Specifications................................................................................................................................5

Installation Instructions .............................................................................................................6

1. Power .................................................................................................................................6

2. Adjusting Stowed Position Height.................................................................................6

Wiring Suggestions .....................................................................................................................7

1. S-Video/Comp and Audio Wiring.................................................................................7

2. VGA Wiring.......................................................................................................................8

3. RS-485 Wiring....................................................................................................................9

4. HDMI..................................................................................................................................9

5. Power & Ground Wiring................................................................................................10

Power/Video................................................................................................................................11

RS-485 Control............................................................................................................................13

Command Sets............................................................................................................................14

RS-485 Network..........................................................................................................................15

Operation Instructions..............................................................................................................16

1. Button Controls ...............................................................................................................16

Troubleshooting.........................................................................................................................18

Technical Drawing.....................................................................................................................19

Technical Support......................................................................................................................20

Instructions for Continued Airworthiness ...........................................................................20

Warranty ......................................................................................................................................21

Log of Revisions.........................................................................................................................22

All manuals and user guides at all-guides.com

Rev:

Revision Date:

08/27/2012

Page 4 of 22

MAN – FD320LIFT-LP Ver HD

General Information

The FD320LIFT-LP Ver HD is a 32" high-definition LCD with Motorized Lift which

allows installation inside a cabinet or credenza. The unit is deployed using a SPDT

Center Off momentary switch to either raise or lower the unit. The LCD automatically

switches on once the unit nears the upper limit. Built with retrofit aircraft integration in

mind, this display can switch between five video input sources using an infrared

remote. The low-profile design adds just under 4 inches to the height of the monitor

alone. This unique design has the retrofit aircraft in mind, reducing the overall space

required for installation. This superior design not only reduces costly modifications to

the aircraft, but allows for larger monitors to be installed in a smaller space.

Front View

Additional Information

The unit features rugged aluminium slides to provide smooth travel when stowing and

deploying. It also incorporates military standard stainless steel wire rope, reinforced

phenolic aircraft pulleys and ball bearing connected to a precision gearbox and driven

by a heavy-duty 24VDC motor. The unit includes holes on the top to allow for

mounting a wood veneer top cover. This feature completely conceals the unit when in

its stowed position inside the cabinet or credenza.

The FD320LIFT-LP Ver HD utilizes a self adjusting tensioner to maintain proper cable

tension. Do not apply excessive downward force on the top of the lift/monitor, this

could overstress the cable and damage the unit.

The FD320LIFT-LP Ver HD utilizes a state of the art digital video decoding chipset for

the analog video input. There are five video source inputs available. They are in order

of picture quality: (2) HDMI (high-definition video, such as Blu-ray DVD or Playstation

3), (1) VGA (computer graphics like Moving Maps), (1) S-Video and (1) Composite

Video (DVD, camera or VCR). Both NTSC and PAL formats are auto-detected.

All manuals and user guides at all-guides.com

Rev:

Revision Date:

08/27/2012

Page 5 of 22

MAN – FD320LIFT-LP Ver HD

The FD320LIFT-LP Ver HD can also be connected to existing video switchers and

simply accept a composite video input from a selector interface box. In this case

multiple input sources can be selected and displayed on the monitor. You would only

use the IR remote to set up the screen during installation. The LCD is protected with a

.125” anti-glare/abrasion Lexan lens to prevent scratching of the LCD.

Specifications

Display

Display Type

32” TFT Color LCD

Display Color

16.7 Million Colors

Screen Resolution

1600x1200 UXGA

Brightness

500 cd/m

Dimensions

31.00”(W) x 18.70”(H) x 2.55”(D)

Display Size

31.51”(800mm) diagonal

Weight

27.3 lbs

Power

28V DC @ 5A

PC & Video Input

VGA (High Density DB-15 Connector),

S-Video, Composite, HDMI (2)

Video Type Supported

NTSC/PAL

Screen Control

On Screen Display Menu

Viewing Angle

178 on Both Axis

Materials

Aluminum

DO-160 Testing

Section 21, Category B

Remote Control

IR, included

Operating Temperature

10C to 30C

Storage Temperature

-10C to 40C

Physical

Lift Power Requirement

28VDC @ 3 AMP

LCD Power Requirement

28VDC @ 5 AMP

Overall Weight

65 lbs

Materials

Aluminum

Stowed Height

33.18”(W) x 23.0”(H) x 5.48”(D)

Deployed Height

33.18”(W) x 42.5”(H) x 5.48”(D)

Operating Temperature

10C to 30C

Storage Temperature

-10C to 40C

DO-160 Testing

Section 21 Category B

All manuals and user guides at all-guides.com

Rev:

Revision Date:

08/27/2012

Page 6 of 22

MAN – FD320LIFT-LP Ver HD

Installation Instructions

All cabin entertainment equipment, such as the FD320LIFT-LP Ver HD, should be

installed on a non-essential bus and have a dedicated circuit breaker. It is a

requirement that a switch be installed in the cockpit so that the pilot can de-energize

the entertainment system should it become necessary.

Power

This is a 28VDC monitor that requires 5 Amps of power to operate the LCD, and 3

Amps of power to operate the mechanical lift. It is recommended that the LCD and lift

be powered by two separate circuit breakers.

Adjusting Stowed Position Height

The FD320LIFT-LP Ver HD down limit can be adjusted up to 1-1/2”. The unit is pre-

adjusted to the lowest stow position. Access the adjustment bolt through the opening

on the top of the lift as shown below. Using a 3/8” wrench turn the down limit

adjustment bolt clockwise to raise the stowed position (display will stop sooner) or

counter-clockwise to lower the stowed position (display will travel further into cabinet).

The upper limit is factory set at the maximum height. In the event this range interferes

with the headliner or other equipment some adjustment is possible. Contact Flight

Display Systems for additional information.

The FD320LIFT-LP Ver HD can be manually lowered in the event power is lost to the

lift. The unit is supplied with a 3-foot flexible drive shaft and panel mount fitting. Attach

the flexible shaft to the gear box shaft as shown and tighten the 2 set screws. Attach

panel mount fitting at access panel. The display can be raised and lowered with the

supplied ¼” speed handle or other ¼” square drive tool.

All manuals and user guides at all-guides.com

all-guides.com

Rev:

Revision Date:

08/27/2012

Page 7 of 22

MAN – FD320LIFT-LP Ver HD

Caution: Limit switches do not function when manually raising or lowering the display.

Be sure not to exceed upper or lower travel limits, this could result in permanent

damage to the FD320LIFT-LP Ver HD.

Wiring Suggestions

All shields should be grounded to the connector at the source, and floating at the

display.

Avoid routing video wiring parallel to:

 AC wiring

 Strobe wiring

 DC motor supply cables

 Inverter cabling

 Or any other potential noise source

S-Video/Composite and Audio Wiring

Recommended cable for s-video/composite and audio purposes is PIC 75 Ohm Coax,

P/N V75268. This is a lightweight, flexible, and low signal loss cable which meets FAA

flammability requirements of FAR 23.1359(d), FAR 25.853(a) and FAR 25.869(a)(4).

All manuals and user guides at all-guides.com

Rev:

Revision Date:

08/27/2012

Page 8 of 22

MAN – FD320LIFT-LP Ver HD

Similar aviation coaxial cable can be used from other vendors, as well.

Some aircraft are prone to AC noise - we recommend adding to the composite source

a 75Ohm video isolation transformer such as Deerfield Laboratory, Inc. Part No. 162-1

(www.deerfieldlab.com, (650) 632-4090). In most cases this should be added to the

video output of the source.

VGA Wiring

Recommended cable for VGA purpose is ECS P/N 453005. This is a single shielded

cable containing 5 separate coaxial cables, color-coded to match the functions of the

wires

Coax cables should be terminated using solder sleeve coaxial cable terminators,

Raychem P/N: CWT-4174-W122-5/9

All manuals and user guides at all-guides.com

Rev:

Revision Date:

08/27/2012

Page 9 of 22

MAN – FD320LIFT-LP Ver HD

RS-485 Wiring

Shielded twisted-pair 22 AWG wire is recommended for RS-485 wiring.

HDMI

HDMI (High-Definition Multimedia Interface) defines the protocol and electrical

specifications for the signaling, pin-out, electrical, and mechanical requirements of

cable and connectors used for transmitting High-Definition content. The Type A HDMI

connector (shown below) has 19 pins with bandwidth to support all SDTV, EDTV, and

HDTV modes. The plug's outside dimensions are 13.9 mm wide by 4.45 mm high.

ECS manufactures an HDMI cable that is terminated at the factory. It is ordered as

part number 600-19786-XXX, where XXX is the length in inches for the desired cable.

Also available from Flight Display Systems is an HDMI to Cat5e/6 converter, which

drastically reduces the cost of cabling while increasing the maximum allowable cable

run to 100ft for High-Definition Video. The FDC5TX (Converts HDMI to Cat5e or Cat6)

and FDC5RX (Converts Cat5e or Cat6 to HDMI) is available for use with

(RECOMMENDED CABLING). Additional information on this product can be found on

the Flight Display Systems website and in the associated manual for these products.

All manuals and user guides at all-guides.com

Rev:

Revision Date:

08/27/2012

Page 10 of 22

MAN – FD320LIFT-LP Ver HD

Power and Ground Wiring

This is a 28VDC monitor that requires 10 amps of power to operate. The rated current

of the equipment and associated voltage drop should be taken into consideration when

selecting wire gauge. To operate properly this monitor requires an input voltage of 25-

32VDC allowing a 3 volt drop on the wire, this is the sum of the voltage drop on the

28V power wire and the voltage drop on the ground or power return wire.

The following examples are based on an install with a 28VDC power system and a total

of 50 feet of wire between the circuit breaker, monitor and ground.

Example 1: 20awg wire has 9.88 Ohms per 1000 feet, this equates to .494 Ohms for

50 feet. 10 Amps of current on .494 Ohms will drop 4.94 Volts. This exceeds the

allowable voltage drop to operate this monitor.

Example 2: 10awg wire has 1.26 Ohms per 1000 feet, this equates to .063 Ohms for

50 feet. 10Amps of current on .063 Ohms will drop 0.63 Volts. This is within the

allowable range to operate this monitor.

Resistance of Wire Type M22759/16-**

(** = Gauge)

Gauge (AWG)

OHMS/1000’

26.20

16.20

9.88

2.02

1.26

.701

Some connector pins are only compatible with the smaller gauge wires. If multiple

power pins are available then all pins should be used. Multiple strands of wire may be

run to the circuit breaker panel, or the multiple small gauge wires may be joined to a

larger gauge wire for a single strand run to the circuit breaker panel. Also, use short

heavy gauge wire and a clean tight connection for ground.

It is the installer's responsibility to understand the product's requirements to install the

product in compliance with industry standards and safety.

All manuals and user guides at all-guides.com

Tabla de contenidos

Otros manuales de Monitor de Flight Display Systems

Flight Display Systems

Flight Display Systems FD171CV-C-4 Manual de usuario

Flight Display Systems

Flight Display Systems FD320CV VER HD Manual de usuario

Flight Display Systems

Flight Display Systems FD201CV-LP VER HD Manual de usuario

Flight Display Systems

Flight Display Systems FD104CV Manual de usuario

Flight Display Systems

Flight Display Systems FD141CV Manual de usuario

Flight Display Systems

Flight Display Systems FD102CV Manual de usuario

Flight Display Systems

Flight Display Systems FD151CV-LP Manual de usuario

Flight Display Systems

Flight Display Systems FD102CV-LP-S Manual de usuario

Flight Display Systems

Flight Display Systems FD201CV-LP VER HD Manual de usuario

Flight Display Systems

Flight Display Systems FD102ARM Manual de usuario

Flight Display Systems

Flight Display Systems FD70ARM-G Manual de usuario

Flight Display Systems

Flight Display Systems FD420CV VER HD Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación