Flair Espresso NEO Flex Manual de usuario
https://airespresso.com/neo-ex-tutorials
Quick Start Guide
1. QR Code for Video Tutorials
2. What’s Included in the Box
3. Assembling your NEO Flex
4. Flow-Control vs. Bottomless 2-in-1 Portalter
5-6. Brewing with your NEO Flex
7. Dialing-In Lever Force
8. Cleaning your NEO Flex
9. Troubleshooting Your NEO Flex
Quick Start Guide Contents QR Code for Video Tutorials
Scan the code below to view video tutorials for your NEO Flex. Seeing is believing and is the best
way to learn to brew beautiful espresso with your Flex.
SCAN ME!
What’s Included in the Box Assembling Your NEO Flex
Align the ns on the front and
back of the base with the
openings in the bottom of the
post. Push down to seat.
12
The Flair logo on the base
and the NEO logo on the post
must be on the same side.
1
2
3
4
5
Main Post & Lever
Base
Piston with Training Disc
(found inside brew cylinder)
Brew Cylinder
Stainless Steel Dispersion Screen
(found inside brew cylinder)
Flow Control Portalter (red)
Silicone Preheat Cap
Extra Flow-Control Spout
Dosing Cup/Tamper
Funnel
Bottomless 2-in-1 Portalter (black)
Training Disc Replacement (1)
Graduation Disc (1)
6
7
8
1
2
3
4
5
6
9
10
910
11
12
8
12
7
11
13
13
Flow-Control vs Bottomless 2-in-1 Portalter
Flow-Control Portalter (Red) Bottomless 2-in-1 Portalter (Black)
Requires a Quality Burr Grinder!
You will need to “dial-in,” or trial dierent sized
grounds until you get the right pressure. Grind too
ne, and you won’t be able to lower the lever. Grind
too coarse, and the lever will lower without any
resistance and not make espresso.
All Brewers Should Start Here!
The Flow-Control Portalter features a restricted exit
port, which builds pressure for brewing espresso in
the chamber. This portalter can be used with almost
any grinder, or with coarse pre-ground coee, without
the need to “dial-in” your shot. Use for convenience.
Featuring a Pressurized Portalter Featuring a Removable Spout
Preheat the
Brew Cylinder
Boil water. Add preheat
cap to bottom of brew
cylinder. Fill with boiled
water. Leave for at least
30 seconds.
Start with the Flow-
Control Portalter
Red portalter – no
special grinder required
- avoid coee grounds
that are too ne.
Prepare your Freshly
Roasted Beans
Start with 15 grams
of beans or grounds
(roughly 3 tablespoons).
If grinding, do so right
before brewing for the
best results.
Separate Your
Brew Head
Separate the brew
head into four parts: 1)
Piston 2) Brew Cylinder
3) Screen 4) Portalter.
Tip: Use dosing cup to
remove piston.
1)
2)
3)
4)
Brewing with Your NEO Flex
Brewing with Your NEO Flex
WARNING:
Never Release
Lever Abruptly!
Boiling Water
May SPRAY!
If Lever Is
Extremely Hard
To Lower, Coee
Grounds Are Too
Fine (see next
page)
1 2 3
45 6
Tamp Lightly & Evenly
on Level Surface
Add Dispersion Screen
to Portalter
Add Preheated Brew
Cylinder to Portalter
Fill to Line with Brew
Water
Insert Piston On Top of
Filled Cylinder
Lower the Lever!
(See Next Page for Lever Force)
Dialing-In Lever Force
Your Flex comes with two “Training Discs” (red); one of which is installed in the piston. Use this red disc as
you learn how much lever force is appropriate. The foil seal of the Training Disc (red) will break if
excess force is applied to the lever, indicating that your grounds are too ne. If the foil breaks,
water will bleed into the brew head. Reattempt with coarser grounds (try ne sea salt consistency if using Flow
Control Portalter) and retest with the second red disc. Extra discs can be purchased on our site.
Training
Disc Broken
Seal
*Remove by pulling out by the
small recess at the edge of the
disc. Push new disc into place.
All discs must have lettering
facing out. Never remove foil of
Training Disc.
Graduation
Disc
Install the “Graduation Disc” (black) once condent that the force applied is never excessive. If trying new coee
with the Graduation Disc and you feel you’re applying excessive force on the lever, carefully STOP brewing and
start over with coarser grounds.
1
2
Cleaning your NEO Flex
Follow the steps below. Cleaning your NEO Flex should be done with water only. No soap is needed, as
it can aect your espresso’s taste. Never put your Flex parts in the dishwasher.
Slowly lift lever and
remove assembled
Brew Head from
NEO Flex frame,
gripping the silicone
where indicated
above.
Troubleshooting your NEO Flex
We recommend periodically ushing your Flow-Control Portalter and brew head with fresh water. This
will prevent the build-up of any coee residue and ensure optimum ow. Simply follow the brewing
steps, without coee, to ush. For more thorough cleaning, remove the ow-control spout and rinse all
pieces with water, as shown below. Leave all portalter parts disassembled and upside down to dry.
Detach portalter
over sink by gripping
portalter in one
hand and silicone
on brew cylinder in
other hand, then
pull apart.
Remove dispersion
screen and eject
grounds by knocking
them out against the
side of a trash can,
or dig the grounds
out with a utensil.
Remove the piston
using the dosing
cup. Place cylinder
over dosing cup and
press down on a
hard surface.
Grip Here
Removable, replaceable
spout to enable cleaning and
declogging. Each Flex comes with
an additional spout. Replace as
necessary and if clogged.
For cleaning: Unscrew the spout cap
and rinse spout and bottom of portalter
in cool water. No soap is needed and
may alter your espresso’s taste.
Rinse all brewing
parts with water
from the tap.
Reminder, don’t use
soap as it will impact
your espresso’s
taste.
Rening Your Brew
To better manage the
force on your lever,
and the pressure in
your system, consider
Or, place your complete Flair on a
bathroom scale to help gauge the
force applied while brewing. 30-40
pounds is the target. Never surpass
70 pounds!
upgrading to our Pressure Gauge Kit.
28-B Hammond Street
Irvine, CA, 92618 USA
© Intact Idea, All Rights Reserved
https://flairespresso.com/contact
Our team is here to help! If you experience any challenges, please reach out:
https://flairespresso.com/warranty
Your NEO Flex is backed by a 1-year limited warranty. For details visit:
Otros manuales de Cafetera de Flair Espresso
