FISCHER DUALSCOPE MP0R USB Manual de usuario

Operator’s Manual for the Coating Thickness

Measuring Instrument

DUALSCOPE®MP0R USB

DUALSCOPE®MP0RH USB

DUALSCOPE®MP0R-FP USB

DUALSCOPE®MP0RH-FP USB

ISOSCOPE®MP0R USB

and variants

DKD-K-33101

Operator’s Manual for

ISOSCOPE®MP0R USB; DUALSCOPE®MP0R(-FP) USB

DUALSCOPE®MP0RH(-FP) USB

Documentation order #: 952-584

Version 4.2 11/2006

Applies to software versions P0R04 and higher

Manufacturer:

HELMUT FISCHER GMBH+CO.KG

Institute for Electronics and Measuring Technology

Industriestrasse 21 71069 Sindelfingen, Germany

Phone ++49 (0) 70 31 30 30

Fax ++49 (0) 70 31 30 379

Internet www.Helmut-Fischer.com

eMail [email protected]

Sindelfingen/Germany.

This operator’s manual remains the copyrighted property of

This manual may not be reproduced by any means (print,

photocopy, microfilm or any other method) in full or in part, or

processed, multiplied or distributed to third parties by

electronic means without the written consent of Helmut

Fischer GmbH+Co.KG. Subject to technical changes and

corrections.

ISOSCOPE®and DUALSCOPE®are registered trademarks of

Helmut Fischer GmbH+Co.KG, Sindelfingen, Germany.

Table of Contents Page

1 Switching the instrument ON / OFF (valid for all instrument models except the “…-FP” models)......................... 5

2 Switching the “…-FP” instrument models ON / OFF............................................................................................. 6

3 Main Menu – Functional Overview ....................................................................................................................... 7

4 Measurements on coating material....................................................................................................................... 8

5 Evaluation of a test series (Statistics function) ................................................................................................... 10

6 Transmitting data to a computer ......................................................................................................................... 12

6.1 Transmitting only the current reading ......................................................................................................... 12

6.2 Transmitting all measurement data in the instrument memory ................................................................... 13

6.3 Sending the current mean value ................................................................................................................. 13

6.3.1 Triggering the mean value transmission manually .............................................................................. 14

6.3.2 Sending the mean value automatically................................................................................................ 14

7 Deleting measurements...................................................................................................................................... 15

7.1 Deleting only the last reading...................................................................................................................... 15

7.2 Deleting all measurement data from the measurement data memory ........................................................ 15

8 Normalizing......................................................................................................................................................... 16

9 Calibration .......................................................................................................................................................... 18

10 Deleting a calibration / Restoring the baseline of the characteristic................................................................. 20

11 Setting the specification limits........................................................................................................................... 22

12 Deleting the specification limits......................................................................................................................... 24

13 Triggering the group separator ......................................................................................................................... 25

14 Service Menus.................................................................................................................................................. 27

15 Trouble Shooting .............................................................................................................................................. 34

16 Technical data .................................................................................................................................................. 39

17 Order information for instruments and accessories .......................................................................................... 46

1 Switching the instrument ON / OFF (valid for all instrument models except the “…-FP” models)

Note: The instrument does not have a specific ON / OFF switch.

Switching the instrument ON

The instrument will switch ON automatically when it is placed on a specimen. If the instrument is placed on

nonferromagnetic or electrically nonconductive material, the display will show the error note "Er6" and then four

horizontal bars instead of a reading.

PLEASE NOTE!

Do not power up the instrument by pressing a finger on the sensor! It may result in erroneous measurements.

Switching the instrument OFF / Auto-Switch-Off

After a certain time, the instrument will switch off automatically (OFF = when instrument’s display is empty)

You can set the period from the last measurement to the automatic OFF from the service mode.

See chapter 14 “Service Menus”, page 27.

2 Switching the “…-FP” instrument models ON / OFF

Note: The on/off operation is different to the other MP0R models!.

Switching the “…-FP” instrument ON

The ON key is the key [OK].

Switch the instrument ON by pressing the key [OK]

Switching the instrument OFF / Auto-Switch-Off

After a certain time, the instrument will switch off automatically (OFF = when instrument’s display is empty)

You can set the period from the last measurement to the automatic OFF from the service mode.

See chapter 14 “Service Menus”, page 27.

3 Main Menu – Functional Overview

Select the specific sub-menus with [] or [] and press key [OK].

4 Measurements on coating material

Making measurements with the MP0R:

1. With the instrument switched ON, place the instrument on the specimen and wait, until the acoustic signal

sounds. The instrument will switch ON automatically this way.

2. Lift the instrument off the specimen.

The acoustic signal sounds and the reading will be displayed. Note: when lifting the instrument too early

(before the beep sound), the error note "Er6" will appear. In this case, repeat step #1.

The measurement is transmitted automatically to the radio receiver (cf. chapter 14 “Service Menus”, page 27,

menu 3, “radio transmission ON/OFF”. The transmission is indicated by the flashing radio tower symbol.

3. When measuring with an instrument which is already swiched ON, a reading will be displayed at once.

As well as with an instrument placed on the specimen and with the instrument lifted off.

Measurement with the MP0R instrument

5 Evaluation of a test series (Statistics function)

Prerequisite: At least two readings must be saved in the measurement data memory.

Note: The measurement data memory must always be empty before starting a test series that is to be evaluated

(cf. chapter 7 "Deleting measurements", page 15). If at least two readings are not stored in memory when you first

press RES and then [OK], the statistical evaluation will NOT start.

Statistical evaluation of a test series:

1. The display menu shows "RES". This is the default setting of the instrument. If RES is not currently shown on

the display, use the arrow key [] or [] to switch to this setting.

2. Press button [OK] repeatedly.

After each [OK], the display will change to the next statistic number (see table below).

3. Press [ESC] or do further measurements to continue a block. This allows to do statistical evaluations within a

test series.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de FISCHER

FISCHER

FISCHER DA03 SR/NM Manual de usuario

FISCHER

FISCHER FERITSCOPE FMP30 Manual de usuario

FISCHER

FISCHER FT90 Manual de usuario

FISCHER

FISCHER MA15F A Series Manual de usuario

FISCHER

FISCHER PERMASCOPE MP0R Manual de usuario

FISCHER

FISCHER MMS Inspection SPG Series Manual de usuario

FISCHER

FISCHER MA15F ... A Series Manual de usuario

FISCHER

FISCHER DA09 series Manual de usuario

FISCHER

FISCHER EA14M Manual de usuario

FISCHER

FISCHER DS21 Manual de usuario

FISCHER

FISCHER DA09 series Manual de usuario

FISCHER

FISCHER DA03 GKT/HLP Manual de usuario

FISCHER

FISCHER ME49F Series Manual de usuario

FISCHER

FISCHER MMS Manual de usuario

FISCHER

FISCHER MS11 Manual de usuario

FISCHER

FISCHER DA01 VUW ATEX Manual de usuario

FISCHER

FISCHER DA12 Manual de usuario

FISCHER

FISCHER DE46 R Series Manual de usuario

FISCHER

FISCHER ME01 Series Manual de instrucciones

FISCHER

FISCHER NK10 H Manual de usuario

FISCHER

FISCHER ECO-LINE FT80 Manual de usuario

FISCHER

FISCHER DELTASCOPE FMP10 Manual de usuario

FISCHER

FISCHER DA12 Manual de usuario

FISCHER

FISCHER MMS Inspection DPM Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario