Firesense PH08-SB Manual de usuario

Outdoor Patio Heater

Instruction Manual

Model# PH08-SB & PH08-SSB

Item # 61220, 61221

Questions, problems, missing parts? Before returning to your

retailer, call our customer service hotline at 1-866-985-7877,

9 a.m. –6 p.m., EST, Monday –Friday or email at

cservice@welltraveled.net.

ATTACH YOUR RECEIPT HERE

Serial Number ______________ Purchase Date _____________

Table of Contents………………………………….....................Page 2

Before You Begin............................................................Page 2

Safety Information.........................................................Page 3-4

Package Contents………………………………….....................Page 5

Hardware Contents..........................................................Page 6

Assembly.........................................................................Page 6-11

Operating Instructions……………......................................Page 12-15

Care and Maintenance……………………..............................Page 15

Troubleshooting……………………………………......................Page 16

Replacement Parts List.....................................................Page 17

Warranty Information…………….....................................…Page 18

BEFORE YOU BEGIN

Please read and understand this entire manual before attempting to assemble, operate or install this appliance.

If you have any questions regarding the product, please call customer service 1-866-985-7877, 9 a.m. –

6 p.m., EST, Monday –Friday.

This manual contains important information about the assembly, operation and maintenance of this patio

heater. General safety information is presented in the first few pages and is also located throughout this manual.

Keep this manual for future reference and to educate new users of this appliance. This manual should be read

in conjunction with the labeling on the appliance. Safety precautions are essential when any mechanical or

propane fueled equipment is involved. These precautions are necessary when using, storing, and servicing.

Using this appliance with the respect and caution demanded will reduce the possibilities of personal injury or

property damage. The following symbols shown below are used extensively throughout this manual. Always

heed these precautions, as they are essential when using any mechanical or propane fueled equipment.

TABLE OF CONTENTS

SAFETY INFORMATION

PACKAGE CONTENTS

ASSEMBLY

PART

PART NAME

QTY

DESCRIPTION/

LOCATION

Tank Housing

Assembly

Pre-assembled

Tank Housing

Assembly contains

cartons with parts

listed below

Stability Ring

Taped to the carton

labeled "Aluminum

Tubes"

Aluminum Tubes

8 pcs/4

sets

Located in carton

labeled "Aluminum

Tubes"

Damper

Located in carton

labeled "Damper

Assembly"

Reflector

Located in carton

labeled "Reflector,

Hardware,Battery,

Manual"

Glass Tube

2 pcs/1

set

Located in

styrofoam carton

labeled "Glass

Tube"

Stainless Steel Ring

Located in

styrofoam carton

labeled "Glass

Tube"

Mesh Guards

8 pcs/4

sets

Located in carton

labeled "Mesh

Guards"

Guard Connector

Located in plastic

bag with hardware

Knob with Chain

Located in carton

labeled "Reflector,

Hardware,Battery,

Manual"

Control Box with Gas

Regulator

Pre-assembled to

Tank Housing

Assembly

PREPARATION

Before beginning assembly of this appliance, make sure all parts are present. Compare all parts with package

contents list as listed on page 5 of this manual. If any part is missing or damaged, do not attempt to assemble

this product. Contact customer service for replacement parts.

ESTIMATED ASSEMBLY TIME: 45 minutes

Tools Required for Assembly (NOT included):

Philips screwdriver w/medium blade

Leak Test Solution

HARDWARE BAG CONTENTS

ASSEMBLY

1. Locate the Tank Housing Assembly (1). Open the front panel and remove the cartons containing all parts

needed for assembly. Note: Each carton will be labeled.

2. Locate the Stability Ring (2) and attach it to the base with the 3 bolts and nuts provided in the bag with

the Stability Ring.

3. Locate the Wheels (A). Loosen and remove the nuts and bolts (4 on each wheel) pre-assembled on each

wheel. Locate the brackets on the rear bottom of the legs of the Tank Housing Assembly (Fig. A.) Align

wheels with the holes in the brackets (make sure the wheel sits flat on the ground as seen in Fig. B.) Attach

the wheels to the brackets using the nuts and bolts you have loosened and removed from the wheels. Once

attached, the wheels should sit slightly above the ground (Fig. C) as wheels should only engage for moving

the heater when the heater is tipped backwards slightly. If wheels are FLAT on the ground once attached to

the brackets with the heater in UPRIGHT position, then wheels are NOT correctly mounted on brackets.

ASSEMBLY

Fig. A

Fig. B

Fig. C

4. Locate the Aluminum Tubes (4). Remove 8 pieces/4 sets of tubes. There will be 4 pieces of tubes that

have a rod protruding from one end and 4 pieces of tubes WITHOUT the protrusion. To fit tubes together,

locate the piece WITHOUT the protrusion and make sure there is a small hole at the bottom of the tube.

Then locate a tube WITH the protrusion and slide the protruding rod into the end of the other tube until the

two holes align. Insert one M3x16 screw (C) and tighten to secure the two rods together. Repeat this with

the other 3 sets (4 sets total, 4 –M3x16 screws total).

5. Once you have the assembled sets of the Aluminum Tubes, slide the bottom of the assembled set (note

that the bottom will have 3 holes—top has NO holes) down over the protruding rod located at each corner

of the Tank Housing Assembly and secure the assembled rod set to the heater on the inside of the rod by

using 2 - M3x16 screws (C) on each corner (4 corners total, 8 - M3x16 screws total). Then secure the

assembled rod set to the heater on the outside of the rod by using 2 –M3x16 screws (4 corners total,

8 –M3x16 screws total).

6. Locate the Damper (4). Attach the Damper to the top of the assembled Aluminum Tubes using 2 –M3x16

screws (C) on each corner (4 corners total, 8 –M3x16 screws total).

ASSEMBLY

7. Locate the Reflector (5). Lean the heater slightly over and attach the Reflector to the Damper using

3 –M3x16 (C) screws.

8. Locate the Glass Tube (6) (2 pcs/1 set), Stainless Steel Ring (7) and Rubber Ring (B). Connect the 2 pcs.

of the Glass Tube with the Stainless Steel Ring by gently inserting one end of the ring into one piece of the

tube and then repeat with the other tube so you have joined the 2 pcs. of the Glass Tube together with the

Ring in the middle.

9. Place the Rubber Ring (B) on the base of the assembled Glass Tube (Fig. A). Check the 3 metal spring

tabs located on the underside of the Damper (Fig. B) and make sure they are bent outward so that when

you begin to insert the Glass Tube, you will not strike the metal spring tabs and also to make sure they do

not get inserted INSIDE the Glass Tube—the spring tabs should be on the OUTER edges of the glass tube.

Then carefully insert the assembled Glass Tube into the hole located on the top of the Tank Housing

Assembly (Fig. C) and slide the top of the assembled Glass Tube into the metal spring tabs located on the

bottom side of the Damper (Fig. D). DO NOT FORCE THE TUBE—it should insert easily.

ASSEMBLY

Fig. A

Fig. B

Fig. C

Fig. D

10.Locate the Mesh Guards (8)--8 pieces/4 sets. There will be 4 pieces that are narrow and 4 pieces that

are wider (Fig A). Begin with the wider pieces and hang them with the hook attached to the mesh guards

onto the assembled Aluminum Tubes (there are 4 oblong holes in each tube—2 at the top and 2 at the

bottom –Fig. B).The wider pieces will go at the bottom and the narrower pieces will go at the top. As you

are hanging the mesh guards, use the Guard Connectors (9) to secure each edge of the wider guard to the

edge of the narrower guard (Fig. C).

11. Locate the Guard Fastening Pieces (D). Screw the Guard Fastening Pieces on the top of the mounting

plate to help keep the Mesh Guards firmly in place using 4 –M3x16 screws (C).

12. Locate the Knob with Chain (10) and screw the knob into the front panel of the Tank Housing Assembly

and attach the chain to the control box.

ASSEMBLY

Fig. A

Fig. B

Fig. C

Otros manuales para PH08-SB

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de patio de Firesense

Firesense

Firesense FireSense 02411 Manual de usuario

Firesense

Firesense 60402 Manual de usuario

Firesense

Firesense FireSense 60697 Manual de usuario

Firesense

Firesense 63057 Especificaciones rápidas

Firesense

Firesense PH01-S Manual de usuario

Firesense

Firesense Deluxe series Manual de usuario

Firesense

Firesense Pro Series Manual de usuario

Firesense

Firesense Mojave Sun IR 60253 Manual de usuario

Firesense

Firesense 60402 Manual de usuario

Firesense

Firesense 60469 Manual de usuario

Firesense

Firesense FireSense 60368 Manual de usuario

Firesense

Firesense 60403 Manual de usuario

Firesense

Firesense 60402 Manual de usuario

Firesense

Firesense PH01-SS Manual de usuario

Firesense

Firesense 61280 Manual de usuario

Firesense

Firesense 60688 Manual de usuario

Firesense

Firesense 60950 Manual de usuario

Firesense

Firesense 28inch Round Fire Pit Manual de usuario

Firesense

Firesense Morrison 62235 Manual de usuario

Firesense

Firesense 60803 Manual de usuario

Firesense

Firesense 60255 Manual de usuario

Firesense

Firesense PH08-SA Manual de usuario

Firesense

Firesense KLD7001S Manual de usuario

Firesense

Firesense 61445 Manual de usuario

Manuales populares de Calentador de patio de otras marcas

empasa

empasa HMXD-E-NHS Manual de usuario

Sunred

Sunred Indus Manual de usuario

HEAT1

HEAT1 ECO pro-line 2300W Manual de usuario

Heatmaxx

Heatmaxx SRPH98 Manual de usuario

Sunjoy

Sunjoy A30600640 Manual de usuario

Event Furniture

Event Furniture 16091 Guía de solución de problemas

Prem-I-Air

Prem-I-Air EH1462 Manual de usuario

Blumfeldt

Blumfeldt 10028637 Manual de usuario

Sunjoy

Sunjoy L-PH011PSS-2 Manual de usuario

Melissa

Melissa 670-202 Manual de usuario

Quality Heating

Quality Heating THE-12DW Manual de usuario

DCS

DCS PHFS-P4 Guía de instalación

EUROM

EUROM 334241 Manual de usuario

Lava Heat

Lava Heat Venetian Manual de usuario

EHS Ltd.

EHS Ltd. HQH-2000W Manual de usuario

VONROC

VONROC ALICUDI PH515AC Manual de usuario

OZONA

OZONA Heatflow IF010997 Manual de operación y mantenimiento

theBBQshop

theBBQshop 51611010 Guía de configuración