Firesense PH01-S Manual de usuario

- 1 -

Patio Heater

Model: PH01-S PH01-SS

Item numbers: 02411,02412,

60755, 60786, 60788

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. If odor continues, immediately

call gas supplier.

PLEASE retain this manual for

reference.

FOR YOUR SAFETY

Do not store or use gasoline or

other flammable vapors or liquids

in the vicinity of this or any other

appliance.

Instruction Manual & Parts List

INSTALLER: Please leave this manual for the consumer.

CONSUMER: Please retain this manual for future reference.

Manufacturer: Changzhou Wellife Furnace Co., Ltd.

WARNING: For outdoor use only.

CERTIFICATE TO ANSI

STD.Z83.26-2007

CONFORM TO CSA

STD.2.37-2007

DANGER CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide

which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed space

such as a camper, tent, car or home.

WARNING :

For Outdoor Use Only

LPG Cylinders to be used must be constructed and

marked in accordance with US DOT specifications.

Storage of the heater indoors is permissible only

if the gas cylinder is turned off and removed.

NOTE:

Use only 20lb LP-Gas tank with size of 18.1in

/ 46cm(Height)*12.5in / 32cm (Width).

Do not use if the environment temperature is

below 40 degrees F / 4.4 degrees C.

WARNING: Improper installation, adjustment,

alteration, service or maintenance can cause injury

or property damage. Read the installation,

operating and maintenance instructions thoroughly

before installing or servicing this equipment.

Tools needed:

●Open end wrench 10 &

13mm (included)

NOT included:

●Adjustable opening wrench

8’’ long

●Philips screwdriver

w/ medium blade

●Spray bottle of soapy

solution for leak testing

Tools and parts needed for assembly

- 2 -

NOTE: PLEASE READ THE FOLLOWING SAFETY RULES

WARNING:

PRECAUTIONS

This heater must only be used outdoors. Using this product in an enclosed area may

cause injury, death or property damage.

Only use in a well-ventilated space. Do not use in a building, garage, or any other

enclosed area.

Read the instructions before use. This heater must be installed in accordance

with local codes or, in the absences of local codes, with the National Fuel Code, ANSI

Z223.1. If applicable, the heater, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with The National

Electrical Code, ANSI/NFPA70.

Do not use the heater in an explosive atmosphere. Keep the heater away from areas

where gasoline or other flammable liquids or vapors are stored.

Prior to use, check for damaged parts such as hoses, regulators, pilot or burner .

Turn off and disconnect LPG cylinder before moving the heater.

Do not attempt to alter this heater in any manner. EXAMPLE: Using the heater without

the top canopy reflector or radiant screen.

Do not shorten the burner post assembly.

Do not use this heater in basements or below ground level. It must always be placed on

a solid and level surface.

Always ensure there is ample fresh air ventilation. For outdoor use ONLY.

Never replace or substitute the regulator with any regulator other than the factory

suggested replacement.

Do not clean the heater with cleaners that are combustible or corrosive.

Do not paint radiant screen, control panel, or top canopy reflector.

All leak tests should be done with a soapy solution. NEVER USE AN OPEN FLAME TO

CHECK FOR LEAKS.

The LPG cylinder should be turned off when the heater is not in use.

At least once a year, the unit should be inspected for the presence of spiders, spider

webs or other insects.

- 3 -

be replaced prior to operating the heater.

Young children should be carefully superv

CHECK THE HEATER IMMEDIATELY IF ANY OF THE FOLLOWING

EXIST:

1. The smell of gas in conjunction with extreme yellow colored tips of the burner flames.

2. The heater does not reach temperature.

3. The burner makes a popping noise during use (a slight popping noise is normal

when the burner is extinguished after using).

Children and adults should be aware of the hazards of high surface temperature,

and should stay away to avoid burns or clothing ignition.

ised when they are in the area of the heater.

Clothing or other flammable material should not be hung from the heater, or placed

on or near the heater.

Any guard or other protective device removed for servicing the heater must

Installation and repair should be done by a qualified service person. The heater should

be inspected before use and cleaning may be required at least once a year, or as

necessary. It is imperative that the control compartment, burner and circulating

passageways of the heater are kept clean.

Keep the heater area clear of combustible materials such as gasoline and other

flammable vapors and liquids.

Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation opening of the LPG cylinder enclosure free and clear of debris.

Storage of a heater indoors is permissible only if the LPG cylinder is turned

off, disconnected and removed from the heater.

Cylinders must be stored outdoors in a well-ventilated area out of the reach

of children. Disconnected cylinders must have threaded valve plugs tightly

installed, and must not be stored in a building, garage or any other enclosed

area.

PRECAUTIONS

- 4 -

ASSEMBLY

1. 3 pcs castle nuts

2. Reflector

3. 6 pcs 8mm washers for pins

support

4. 3 pcs 90mm (L) pins for

reflector support

5. Head assembly

6. 4 pcs M6x10mm bolts

7. 2 pcs Post assembly

8. Tank housing

9. Regulator

10. 6 pcs M6x30mm bolts and

6mm nuts for connection of

post support and support

legs

11. 3 pcs M8x16mm bolts for

connection of support

legs and base

12. Post support

13. 6pcs M6x12mm bolts and 6pcs

M6 screw for connection LPG

cylinder fixed parts with base,

6pcs M8x25mm bolts for

securing the cylinder

14. 3 pcs Support legs

15. Base

16. 1 pc open end wrench

(10&13mm) NOT PICTURED

17.

18. Wheel assembly

Gas hose

(attached to head assembly)

- 5 -

ATTACHING WHEEL ASSEMBLY

Step 1

1-1. Locate Wheel Assembly (17) and 2 nuts/bolts

contained in plastic bag with Wheel Assembly

(Fig. 1).

Step 2

2-1. Turn Base (15) so that holes for attachment of

Wheel Assembly are facing you (Fig. 2).

2-2. Align holes in Wheel Assembly (17) with

holes on Base (15) (Fig. 3).Insert bolts through both sets of holes

and secure nuts on end of bolt (Fig. 4).

Step 3

3-1. Wheel Assembly (17) should now be attached to Base (15)

as shown (Fig. 5).

ASSEMBLY

Fig. 1

Fig. 2

Fig. 3 Fig. 4

Fig. 5

- 6 -

WARNING: This appliance requires installation by a competent person.

Proper assembly is the responsibility of the installer.

Step 1

1-1. Attach 3pcs LPG cylinder fixed parts on the

base with 6pcs M6x12mm bolts.

1-2. Position the 3 pcs support legs on the base as

shown in the picture to the right.

1-3. Use 3 pcs M8x16mm bolts to affix the support

legs to the base.

Step 2

2-1. Put the post support on top of the 3 pcs support

legs.

2-2. Use 6 pcs M6x30mm bolts and nuts to connect

the post support to the 3 pcs support legs.

2-3. Use 4 pcs. M6X10mm bolts to connect the first

piece of the post assembly to the post support.

ASSEMBLY

- 7 -

-8 -

Step 3

3-1. Connect the second piece of the post assembly

to the first piece of the post assembly and screw on

clockwise.

Step 4

4-1. Place the tank cover on the base.

Step 5

5-1. Secure the 3 pcs 90mm pins(reflector

support bolts) on the cap of emitter screen.

5-2. Route the gas hose down through the post and

out of the bottom.

5-3. Connect the regulator with gas hose.

5-4.Fix the head unit collar to the post with 4 pcs.

M6x10mm bolts.

ASSEMBL

Reflector (#2) is comprised of 3 – outer pieces and 1 – center piece. Locate all 4

pieces of Reflector (#2) which are wrapped in bubble wrap. Unwrap and remove

all pieces and peel off the protective blue plastic on each piece. Locate 9 bolts and

9 cap nuts in the plastic bag. Align the 3 – outer pieces with the 1 – center piece

and place a bolt through the center hole on each piece as shown below. Tighten

castle nut on each bolt.

ASSEMBLY

Next, align the sides of each outer piece and the center piece and insert the

next 3 bolts through both holes. Tighten castle nuts on bolts.

Finally, insert bolt through holes located at outside edge of adjoining panels

of the reflector side pieces (3 bolts required) and tighten castle nuts on bolts.

- 9 -

Step 6

6-1. Put 8mm washer on each reflector support

bolt.

6-2. Fasten the reflector with 3 pcs washers

and 3 pcs M8 mm castle nuts.

Step 7

7-1. Lift the tank cover and rest it on the post flange.

7-2. Connect the end of gas hose to

the regulator hose. Connect the regulator

to the gas cylinder.

Warning: When connecting the gas cylinder and regulator, make sure the

connection is tight and always check for any leaks. Please see page 11

“Check for Leak” for full instructions.

7-3. Put gas cylinder on the base.

ASSEMBLY

- 10 -

Otros manuales para PH01-S

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de patio de Firesense

Firesense

Firesense KLD7001S Manual de usuario

Firesense

Firesense 61445 Manual de usuario

Firesense

Firesense 60950 Manual de usuario

Firesense

Firesense KLD7003SB Especificaciones rápidas

Firesense

Firesense 2109 Manual de usuario

Firesense

Firesense FireSense 60696 Manual de usuario

Firesense

Firesense 60403 Manual de usuario

Firesense

Firesense 1902415 Especificaciones rápidas

Firesense

Firesense 60402 Manual de usuario

Firesense

Firesense PH08-SA Manual de usuario

Firesense

Firesense 2117 Manual de usuario

Firesense

Firesense steel pagoda Manual de usuario

Firesense

Firesense LIP-10A-TGG/60951 Manual de usuario

Firesense

Firesense 60402 Manual de usuario

Firesense

Firesense FireSense 60485 Manual de usuario

Firesense

Firesense FireSense PH08-S Manual de usuario

Firesense

Firesense 60788 Manual de usuario

Firesense

Firesense KLD7001S Manual de usuario

Firesense

Firesense FireSense 60697 Manual de usuario

Firesense

Firesense FireSense 02411 Manual de usuario

Firesense

Firesense LIP-10A-TGG-LPG-BU Manual de usuario

Firesense

Firesense 60803 Manual de usuario

Firesense

Firesense 2127168 Especificaciones rápidas

Firesense

Firesense KLD7001S Manual de usuario

Manuales populares de Calentador de patio de otras marcas

empasa

empasa HMXD-E-NHS Manual de usuario

Sunred

Sunred Indus Manual de usuario

HEAT1

HEAT1 ECO pro-line 2300W Manual de usuario

Heatmaxx

Heatmaxx SRPH98 Manual de usuario

Sunjoy

Sunjoy A30600640 Manual de usuario

Event Furniture

Event Furniture 16091 Guía de solución de problemas

Prem-I-Air

Prem-I-Air EH1462 Manual de usuario

Blumfeldt

Blumfeldt 10028637 Manual de usuario

Sunjoy

Sunjoy L-PH011PSS-2 Manual de usuario

Melissa

Melissa 670-202 Manual de usuario

Quality Heating

Quality Heating THE-12DW Manual de usuario

DCS

DCS PHFS-P4 Guía de instalación

EUROM

EUROM 334241 Manual de usuario

Lava Heat

Lava Heat Venetian Manual de usuario

EHS Ltd.

EHS Ltd. HQH-2000W Manual de usuario

VONROC

VONROC ALICUDI PH515AC Manual de usuario

OZONA

OZONA Heatflow IF010997 Manual de operación y mantenimiento

theBBQshop

theBBQshop 51611010 Guía de configuración