Fire Pro FP-08450 Manual de usuario

Fire Detection and

Activation System

Model 08450

Rev 2.7

Page | 2 
Contents 
Introduction ............................................................................................ 3 
1 General Information ....................................................................... 3 
2 How Does it Work .......................................................................... 3 
3 In Case of Fire ............................................................................... 3 
Components List...................................................................................... 4 
Design Considerations.............................................................................. 5 
1 Main Power Supply Input ................................................................ 5 
2 Backup Power Supply Input ............................................................ 5 
3 Siren/Strobe Output ....................................................................... 5 
4 Discharge Output ........................................................................... 5 
5 Detection Circuit 1 Alarm Output ..................................................... 6 
6 Detection Circuit 2 Alarm Output ..................................................... 6 
7 Mounting ....................................................................................... 6 
8 Cabling Requirements..................................................................... 7 
9 Connecting Multiple FirePro Generators ........................................... 7 
Installation .............................................................................................. 8 
Wiring Diagram ......................................................................................12 
Programming..........................................................................................13 
Operation...............................................................................................13 
1 LED Indicators ..............................................................................13 
2 Isolate Function ............................................................................13 
3 Reset Function ..............................................................................14 
4 Test Function ................................................................................14 
5 Discharging the Fire System...........................................................14 
6 Alarm Silence ................................................................................14 
Commissioning .......................................................................................15 
Servicing and Maintenance ......................................................................16 
1 Daily Service Schedule...................................................................16 
2 Semi-annual / Annual Service Schedule ..........................................16 
Troubleshooting......................................................................................17 
1 Internal Faults...............................................................................17 
2 External Faults ..............................................................................17 
Specifications .........................................................................................18 
RFI Environments ...................................................................................19 
Safety Data Sheet (SDS) - FirePro............................................................19 
Marine Installation Notes (AMSA NSCV)....................................................20 
 
 

Page | 3

1Introduction

1.1 General Information

The FirePro FP-08450 Fire Control Panel is a combined detection and extinguishant system,

and is compliant for use in marine (AMSA NSCV).

The FIP (fire indicator panel) incorporates:

-2x Detection circuits;

-1x Extinguishing Discharge circuit;

-1x Siren/Strobe circuit;

-Programmable Activation (automatic and/or manual);

-Fault Monitoring system;

-Isolation Function.

1.2 How Does it Work

All FirePro Aerosol Generators use the latest generation FPC solid compound. Upon activation,

the solid compound is transformed into a rapidly expanding, highly efficient gas, based on

Potassium salts. It does not deplete oxygen levels. The built-in fail-safe activation system

ensures operation of the generators when required, even if everything else fails. At 300⁰C the

FPC block changes to a potassium-based gas to extinguish the fire.

Ozone Depletion Potential (O.D.P.) = 0

Atmospheric Life Time (A.L.T.) = 0

Global Warming Potential (G.W.P.) = 0

Non-corrosive & Non-toxic

1.3 In Case of Fire

If a fire occurs, equipment operators should do the following:

1. Detection will initiate an alarm condition on the FirePro System

2. The siren/strobe will operate and if shutdown relays have been installed, equipment

shutdown will be initiated.

3. Evacuate all personnel from the risk area.

4. Close all hatches and openings, and shutdown engines and any extraction fans or vents.

5. Manual Activation: Press and hold both mode switches continuously for 5 seconds to

activate the system.

6. Remote Activation Switches: The control panel will automatically begin the activation

sequence when remote activation switches (where installed) are pushed (Det Circuit 1).

7. Keep the FirePro suppression gas within the risk until the fire is extinguished and not able

to re-ignite.

8. Do not start engine or fans until the fire is extinguished. Operating the exhaust fans will

enable the gas to escape the risk area and could allow the fire to re-ignite.

9. Do not enter the risk until it has been rendered safe.

10.Recommended clean up after discharge is with soapy water and a cleaning agent based on

citric acid.

11.Following a discharge, replace all installed FirePro Generators.

Page | 4

2Components List

FP-08450

Fire Control Panel

Detection and extinguishant

control system

4x DP-3000

1x DP-2000

2x FP-08950

Deutsch Plug 3 Pin F, c/w heatshrink

Deutsch Plug 3 Pin M, c/w heatshrink

End-of-line Plug 4k7Ω(Detection)

End-of-line Diode 1N4004 (Siren/Strobe)

Charging Diode 1N5404 (Backup Power)

End-of-Line Resistor 3k3Ω (Discharge)

Operator’s Manual

Agent Release Circuit

Siren / Strobe Circuit

FP-08918

Wiring loom and Splitter Cable for

installaion of multiple FirePro

generators.

FP-08940

Siren/Strobe

Discharge Circuit

FirePro Aerosol

Generator

100g –500g Unit.

Constructed from Stainless Steel.

Comes with installed Deutsch Plug

for easy install

FP-6200

Heavy Duty Bracket 316 SS.

Suits FP-100, 200, 500 FirePro

Aerosol Generators.

FirePro Aerosol

Generator

1200g –5700g Unit.

Constructed from Stainless Steel.

Comes with installed Deutsch Plug

for easy install.

FP-6100

Heavy Duty Bracket 316 SS.

Suits FP-1200, 2000, 3000 5700

FirePro Aerosol Generators.

Detection Circuit (Circuit 1 Alarm & Circuit 2 Alarm)

FP-08920

Marine Grade Thermal Detector

60°C Fixed. Other temperatures

available on request.

FP-14053

Manual Call Point

Internal OR External

FP-09510

Linear Heat Detection Cable 182° C

FP-09511

Linear Heat Detection Installation kit.

Mounting Clips, 2x Junction Boxes

with strain relief cable glands and 1x

EOL for monitoring.

Installation Components

Service Components

FP-09500

2 Hour Fire Rated Shielded Cable.

FP-08960

Signage for the System. A sheet of

different size labels.

FP-08870/8871/8872

Power Control Module

Provides back up power for control

panel.

FP-08800

FirePro Simulator –for Testing &

Commissioning.

Additional Modules

FP-08850

Discharge Delay Module

Allows additional FirePro generators

to be discharged

FP-08860

Shutdown Relay Module

Provides facility for equipment

shutdown

Page | 5

3Design Considerations

3.1 Main Power Supply Input

The FP-08450 Fire Control Panel provide a single power supply input that is compatible with

12 / 24vDC. If adequate power is not supplied, the LEDs will not be illuminated, and the

control panel will not operate. The main power supply should be connected directly to a battery

or power source, not through a distribution board. The main power must not be interrupted if

the vessel is powered down. The FirePro Battery Lead (P/N FP-14016) may be used to connect

power to the control panel.

The recommended configuration is to use the vessel’s emergency batteries, provided that the

vessel has an automatic changeover for its power supply.

3.2 Backup Power Supply Input

A secondary power supply is required for marine installations. Where the vessel’s emergency

batteries are not suitable, the control panel will need to be connected to a secondary power

supply or the FP-08870/08871 Power Control Module will be required. The secondary power

supply should be connected directly to a battery or power source, not through a distribution

board. The secondary power supply must not be interrupted if the vessel or main power supply

is powered down. Note: The secondary power supply must be the same voltage as the main

power source.

3.3 Siren/Strobe Output

A siren is required for all marine installations. The recommended siren/strobe is the Flashni

Xenon Sounder Beacon. In a typical install, the maximum number of supported sirens/strobes

that can be installed is 5. When installed, Siren/Strobes are to be clearly visible and audible

at all points around the risk area.

The siren/strobe output is a monitored circuit. The supplied end-of-line diode (1N4004) must

be installed on the last siren/strobe in the circuit, otherwise the fire control panel will display

a fault.

3.4 Discharge Output

The maximum number of FirePro generators able to be discharged by the FP-08450 Fire

Control Panel is limited by the voltage of the main power supply. That is:

Voltage 12vDC Max = 2 Units

Voltage 24vDC Max = 4 Units

If a risk area requires a greater number of FirePro generators to be discharged than the

standard panel can provide, the FP-08850 Discharge Delay module can be used. The module

will discharge generators in multiples up to the maximum as above.

If the number of FirePro generators connected to each output is greater than the

maximum, the fire system will not operate.

When multiple FirePro generators are connected to a single output, they must be connected

using the FP-08919 Splitter Lead (see 3.9 Connecting Multiple FirePro Generators).

If a suppression system is not used, the supplied end-of-line resistor (3k3Ω) must be connected

to the Discharge output using the supplied deutsch plugs.

Page | 6

3.5 Detection Circuit 1 Alarm Output

The Circuit 1 Alarm Output is a zoned detection circuit capable of operating up to 30

conventional detectors, 100 metres of linear heat detection cable or 30 manual call points.

The Circuit 1 Alarm Output can be programmed for detection and alarm, or for automatic

discharge if an alarm is detected on this circuit (see 6. Programming).

Where remote actuation is needed, the FP-14053 Manual Call Point may be installed, and

Circuit 1 Alarm programmed for automatic discharge. Note: If remote activation is used, no

other detection devices should be installed on Circuit 1 Alarm.

The supplied end-of-line resistor (4k7Ω) must be installed on the last detector or manual call

point in the circuit, otherwise the fire control panel will display a fault. If detection is not used,

the supplied end-of-line plugs (marked green) must be connected to the Circuit 1 Alarm output.

3.6 Detection Circuit 2 Alarm Output

The Circuit 2 Alarm Output is a zoned detection circuit capable of operating up to 30

conventional detectors, 100 metres of linear heat detection cable or 30 manual call points.

The Circuit 2 Alarm Output is a detection and alarm circuit only. When in alarm condition the

siren/strobe will operate, however the suppression system will not discharge until manually

operated.

The supplied end-of-line resistor (4k7Ω) must be installed on the last detector or manual call

point in the circuit, otherwise the fire control panel will display a fault. If detection is not used,

the supplied end-of-line plugs (marked green) must be connected to the Circuit 2 Alarm output.

3.7 Mounting

For correct installation, the Fire Control Panel must be mounted by bolts or screws through the

mounting holes in the flange on both sides of the Module. No penetrations are to be made

through the casing of the panel. The Fire Control Panel enclosure is rated IP54, so should

be installed in a convenient location, away from where it may be affected by water.

It is necessary to complete all wiring and any programming of the detection mode prior to

mounting the panel.

Page | 7

3.8 Cabling Requirements

When constructing extension leads the supplied Deutsch Plugs must be used to ensure water-

proof connections are made throughout the installation.

1. Cut cable to required length and strip outer insulation to approximately 25-30mm.

2. Strip inner insulation to approximately 6mm and using a Deutsch Crimping tool, fix pins to

the exposed ends of the cable, including the earth where applicable.

3. Place heat shrink over the end of the cable.

Identify correct socket on plug by the

numbers/letter on the side of the plug and

push through the gasket at the bottom of the

plug until a click is heard and the pin is locked

in place.

4. Place the locking mechanism inside the plug to ensure pins remain secure. (Male plugs;

locking mechanism is orange. Female plugs; locking mechanism is green).

5. Using the heat shrink, seal the back of the

plug.

Cables are colour coded for easy identification.

When installing system, cables should be only

connected to the correctly coded cable. Colour

Coding for cables is as follows:

3.9 Connecting Multiple FirePro Generators

If multiple FirePro Generators are being installed on a single output, they must be connected

using the FP-08918 Splitter Lead. The Splitter Lead enables the activation current to pass

uninterrupted to all connected FirePro generators and allows for continuous monitoring.

Splitter Leads can be installed at any point on the activation circuit and do not need to be

installed adjacent to the fire control panel or the discharge delay module. For ease of install,

servicing and more efficient field wiring, Splitter Leads should be installed in areas easy to

access and should be used to minimise the required extension leads, and to bypass obstacles.

Colour

Circuit

Red

Power Supply

Yellow 1

Activation

Yellow 2

Activation Delayed

Green 1

Detection 1

Green 2

Detection 2

Orange

Siren/Strobe

White

Relay Output

Page | 8

4Installation

FirePro generators must remain disconnected until system is completed and fire control panel

is no longer in a fault or alarm condition. The FirePro Universal Test Lamp (P/N FP-08800) can

be used to take the panel out of a fault condition.

Note: Any required extension leads must be constructed as per the instructions in 3.8 Cabling

Requirements.

Note: It is recommended that one circuit is installed and connected at a time to isolate the

cause of any faults that may occur during installation. The supplied End-of-line plugs and Test

Lamp may be used to keep the control panel out of a fault condition.

1. Main Power: When panel has been mounted in a suitable location, connect main supply

power using a Lead to the power input (marked red). The recommended source for the

main power supply input is the vessel’s emergency batteries.

2. Backup Power: Where the vessel’s emergency batteries are not suitable, the control panel

will need to be connected to a secondary power supply (see below) or the FP-08870/08871

Power Control Module (see product manual).

If a secondary power supply is used, it must be the same voltage as the main power

source. The supplied 1N5404 Charging Diode must be installed in the positive terminals of

Main Power and Backup Power. The diode is polarised, so the positive lead of the diode

(marked with a grey band) should be terminated in terminal 3 (+ Backup Power) and the

negative lead terminated in terminal 1 (+ Main Power).

Page | 9

3. Siren/Strobe Circuit: Mount the siren/strobe (P/N FP-08940) in a location where it is

visible and audible in all points with the risk area and connect to the “Siren” output on the

module (marked orange). If more than one siren/strobe is being installed, they are to be

connected using the secondary positive/negative terminals in the sounder.

The supplied end-of-line diode should be installed in the secondary positive/negative

terminals of the last siren/strobe in the circuit. The diode is polarised, so the positive lead

of the diode (marked with a grey band) should be terminated in the positive terminal of

the siren/strobe, otherwise a fault will occur on the fire control panel.

4. Circuit 1 Alarm Circuit: This circuit can be programmed for ALARM ONLY (operate

siren/strobe) or AUTOMATIC DISCHARGE (discharges suppression system and operates

siren/strobe). If detection is not used, the supplied end-of-line plugs (marked green) must

be connected to the Circuit 1 Alarm output.

-Manual Call Point: Manual Call Points (P/N FP-14053) can be connected together in

quantities up to 30. If a manual call point is being used for remote activation, it must

be installed on Circuit 1 Alarm. The supplied end-of-line plugs (marked green) must be

connected to the last manual call point in the circuit.

-Linear Heat Detection: Linear Heat Detection can be installed in lengths up to 100m.

Any terminations of cable must be enclosed using sealed, metal enclosures from the

LHD Install Kit (P/N FP-09511). P-Clips must be installed at intervals of 50cm maximum

to support the cable. The supplied End-of-line junction box must be installed on the

end of the cable.

Page | 10

-Conventional Detector (Thermal / Smoke): Conventional Detector (P/N FP-08920

Thermal / FP-94140 Smoke) can be connected together in quantities up to 30. A 4k7Ω

End-of-line resistor must be installed in the last detector in the circuit.

-Detection Not Used: If detection is not used, the supplied end-of-line plugs (marked

green) must be connected to the Circuit 1 Alarm output.

5. Circuit 2 Alarm Circuit: This circuit is ALARM ONLY and will only operate the

siren/strobe. Connections for detection and manual call points are the same as Circuit 1

Alarm. If detection is not used, the supplied end-of-line plugs (marked green) must be

connected to the Circuit 2 Alarm output.

6. Discharge Circuit: This circuit should remain disconnected until all other circuits are

connected. The control panel must not be in an alarm/fault condition when the FirePro

generators are connected, as this may cause an accidental discharge. A Universal Test

Lamp (P/N FP-08800) should be connected to take the control panel out of fault condition

and for any commissioning.

-Mounting FirePro Generators: FirePro Generators must be installed using only

approved brackets with observation of the relevant stream lengths and thermal

clearances noted in the design calculation and risk assessment. Generators should be

mounted near the top of the risk area, with care taken to aim generators away from

openings or obstacles that may impede dispersion of the suppression agent. Egress

routes for personnel must be kept clear, and not be obstructed by any installed

components or by agent dispersion.

Tabla de contenidos

Otros manuales de Panel de control de Fire Pro

Fire Pro

Fire Pro 08100 Manual de usuario

Fire Pro

Fire Pro FPC-2 Manual de usuario

Fire Pro

Fire Pro FPC-2 Manual de usuario

Fire Pro

Fire Pro FP-22408 Manual de usuario

Fire Pro

Fire Pro FPC-2 Manual de usuario

Fire Pro

Fire Pro 08451 Manual de usuario

Fire Pro

Fire Pro Sigma XT Guía de referencia

Fire Pro

Fire Pro FPX103C Manual de usuario

Fire Pro

Fire Pro 08451 Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas