Apply thread tape (or similar) to the ½" connection,
then screw the top rail connector to the connection.
Screw the bottom rail connector to a wall stud
making sure it is vertically in line with the top rail
connector. Maximum centre distance between the
top and bottom shower connections is 650mm.
Check the grub screws are wound tight. Push the rail
brackets onto the top and bottom rail connectors
until they are against wall. Secure with grub screws.
1. 2. 3. 4.
5.
Clean filter washer
periodically
Water contains lime which remains on the surface
after the water has evaporated. These lime deposits
can be prevented from forming by wiping
immediately after use.
To clean the chrome-plated surfaces use a soft
cloth, soap and warm water. Never use cleaning
agents that contain a corrosive acid or a scouring
additive.
CLEANING
Do not use any
sharp objects
to clean nozzles
Top Rail
Bracket
Bottom Rail
Bracket
Remove the protective cap from the showerhead
ball joint and screw the unit onto the overhead
arm ensuring the filter washer is in place.
This arm is not adjustable.
6.
Min 13±2mm
Max
/25mm
Water Inlet
Connector
WATER INLET: RECOMMENDED MINIMUM HEIGHT
OF 1800mm FROM FLOOR LEVEL
Install a ½" male threaded connection at the
recommended height on wall, ensuring that a
minimum of 13±2mm of thread protrudes past
the finished wall.
Correct water proong must be applied.
650mm
Rail Connector
Water Inlet
Connector
Make sure a washer is in both ends of the hose.
Screw hose onto lower outlet on rail, attach
handset and place firmly in holder. Tilt and rotate
head to the desired position.
Filter Washer
Ball Joint
Apply thread tape (or similar) to the ½" connection,
then screw the top rail connector to the connection.
Screw the bottom rail connector to a wall stud
making sure it is vertically in line with the top rail
connector. Maximum centre distance between the
top and bottom shower connections is 650mm.
Check the grub screws are wound tight. Push the rail
brackets onto the top and bottom rail connectors
until they are against wall. Secure with grub screws.
1. 2. 3. 4.
5.
Clean filter washer
periodically
Water contains lime which remains on the surface
after the water has evaporated. These lime deposits
can be prevented from forming by wiping
immediately after use.
To clean the chrome-plated surfaces use a soft
cloth, soap and warm water. Never use cleaning
agents that contain a corrosive acid or a scouring
additive.
CLEANING
Do not use any
sharp objects
to clean nozzles
Top Rail
Bracket
Bottom Rail
Bracket
Remove the protective cap from the showerhead
ball joint and screw the unit onto the overhead
arm ensuring the filter washer is in place.
This arm is not adjustable.
6.
Min 13±2mm
Max
/25mm
Water Inlet
Connector
WATER INLET: RECOMMENDED MINIMUM HEIGHT
OF 1800mm FROM FLOOR LEVEL
Install a ½" male threaded connection at the
recommended height on wall, ensuring that a
minimum of 13±2mm of thread protrudes past
the finished wall.
Correct water proong must be applied.
650mm
Rail Connector
Water Inlet
Connector
Make sure a washer is in both ends of the hose.
Screw hose onto lower outlet on rail, attach
handset and place firmly in holder. Tilt and rotate
head to the desired position.
Filter Washer
Ball Joint
Apply thread tape (or similar) to the ½" connection,
then screw the top rail connector to the connection.
Screw the bottom rail connector to a wall stud
making sure it is vertically in line with the top rail
connector. Maximum centre distance between the
top and bottom shower connections is 650mm.
Check the grub screws are wound tight. Push the rail
brackets onto the top and bottom rail connectors
until they are against wall. Secure with grub screws.
1. 2. 3. 4.
5.
Clean filter washer
periodically
Water contains lime which remains on the surface
after the water has evaporated. These lime deposits
can be prevented from forming by wiping
immediately after use.
To clean the chrome-plated surfaces use a soft
cloth, soap and warm water. Never use cleaning
agents that contain a corrosive acid or a scouring
additive.
CLEANING
Do not use any
sharp objects
to clean nozzles
Top Rail
Bracket
Bottom Rail
Bracket
Remove the protective cap from the showerhead
ball joint and screw the unit onto the overhead
arm ensuring the filter washer is in place.
This arm is not adjustable.
6.
Min 13±2mm
Max
/25mm
Water Inlet
Connector
WATER INLET: RECOMMENDED MINIMUM HEIGHT
OF 1800mm FROM FLOOR LEVEL
Install a ½" male threaded connection at the
recommended height on wall, ensuring that a
minimum of 13±2mm of thread protrudes past
the finished wall.
Correct water proong must be applied.
650mm
Rail Connector
Water Inlet
Connector
Make sure a washer is in both ends of the hose.
Screw hose onto lower outlet on rail, attach
handset and place firmly in holder. Tilt and rotate
head to the desired position.
Filter Washer
Ball Joint
Apply thread tape (or similar) to the ½" connection,
then screw the top rail connector to the connection.
Screw the bottom rail connector to a wall stud
making sure it is vertically in line with the top rail
connector. Maximum centre distance between the
top and bottom shower connections is 650mm.
Check the grub screws are wound tight. Push the rail
brackets onto the top and bottom rail connectors
until they are against wall. Secure with grub screws.
1. 2. 3. 4.
5.
Clean filter washer
periodically
Water contains lime which remains on the surface
after the water has evaporated. These lime deposits
can be prevented from forming by wiping
immediately after use.
To clean the chrome-plated surfaces use a soft
cloth, soap and warm water. Never use cleaning
agents that contain a corrosive acid or a scouring
additive.
CLEANING
Do not use any
sharp objects
to clean nozzles
Top Rail
Bracket
Bottom Rail
Bracket
Remove the protective cap from the showerhead
ball joint and screw the unit onto the overhead
arm ensuring the filter washer is in place.
This arm is not adjustable.
6.
Min 13±2mm
Max
/25mm
Water Inlet
Connector
WATER INLET: RECOMMENDED MINIMUM HEIGHT
OF 1800mm FROM FLOOR LEVEL
Install a ½" male threaded connection at the
recommended height on wall, ensuring that a
minimum of 13±2mm of thread protrudes past
the finished wall.
Correct water proong must be applied.
650mm
Rail Connector
Water Inlet
Connector
Make sure a washer is in both ends of the hose.
Screw hose onto lower outlet on rail, attach
handset and place firmly in holder. Tilt and rotate
head to the desired position.
Filter Washer
Ball Joint
Apply thread tape (or similar) to the ½" connection,
then screw the top rail connector to the connection.
Screw the bottom rail connector to a wall stud
making sure it is vertically in line with the top rail
connector. Maximum centre distance between the
top and bottom shower connections is 650mm.
Check the grub screws are wound tight. Push the rail
brackets onto the top and bottom rail connectors
until they are against wall. Secure with grub screws.
1. 2. 3. 4.
5.
Clean filter washer
periodically
Water contains lime which remains on the surface
after the water has evaporated. These lime deposits
can be prevented from forming by wiping
immediately after use.
To clean the chrome-plated surfaces use a soft
cloth, soap and warm water. Never use cleaning
agents that contain a corrosive acid or a scouring
additive.
CLEANING
Do not use any
sharp objects
to clean nozzles
Top Rail
Bracket
Bottom Rail
Bracket
Remove the protective cap from the showerhead
ball joint and screw the unit onto the overhead
arm ensuring the filter washer is in place.
This arm is not adjustable.
6.
Min 13±2mm
Max
/25mm
Water Inlet
Connector
WATER INLET: RECOMMENDED MINIMUM HEIGHT
OF 1800mm FROM FLOOR LEVEL
Install a ½" male threaded connection at the
recommended height on wall, ensuring that a
minimum of 13±2mm of thread protrudes past
the finished wall.
Correct water proong must be applied.
650mm
Rail Connector
Water Inlet
Connector
Make sure a washer is in both ends of the hose.
Screw hose onto lower outlet on rail, attach
handset and place firmly in holder. Tilt and rotate
head to the desired position.
Filter Washer
Ball Joint
Apply thread tape (or similar) to the ½" connection,
then screw the top rail connector to the connection.
Screw the bottom rail connector to a wall stud
making sure it is vertically in line with the top rail
connector. Maximum centre distance between the
top and bottom shower connections is 650mm.
Check the grub screws are wound tight. Push the rail
brackets onto the top and bottom rail connectors
until they are against wall. Secure with grub screws.
1. 2. 3. 4.
5.
Clean filter washer
periodically
Water contains lime which remains on the surface
after the water has evaporated. These lime deposits
can be prevented from forming by wiping
immediately after use.
To clean the chrome-plated surfaces use a soft
cloth, soap and warm water. Never use cleaning
agents that contain a corrosive acid or a scouring
additive.
CLEANING
Do not use any
sharp objects
to clean nozzles
Top Rail
Bracket
Bottom Rail
Bracket
Remove the protective cap from the showerhead
ball joint and screw the unit onto the overhead
arm ensuring the filter washer is in place.
This arm is not adjustable.
6.
Min 13±2mm
Max
/25mm
Water Inlet
Connector
WATER INLET: RECOMMENDED MINIMUM HEIGHT
OF 1800mm FROM FLOOR LEVEL
Install a ½" male threaded connection at the
recommended height on wall, ensuring that a
minimum of 13±2mm of thread protrudes past
the finished wall.
Correct water proong must be applied.
650mm
Rail Connector
Water Inlet
Connector
Make sure a washer is in both ends of the hose.
Screw hose onto lower outlet on rail, attach
handset and place firmly in holder. Tilt and rotate
head to the desired position.
Filter Washer
Ball Joint
Apply thread tape (or similar) to the ½" connection,
then screw the top rail connector to the connection.
Screw the bottom rail connector to a wall stud
making sure it is vertically in line with the top rail
connector. Maximum centre distance between the
top and bottom shower connections is 650mm.
Check the grub screws are wound tight. Push the rail
brackets onto the top and bottom rail connectors
until they are against wall. Secure with grub screws.
1. 2. 3. 4.
5.
Clean filter washer
periodically
Water contains lime which remains on the surface
after the water has evaporated. These lime deposits
can be prevented from forming by wiping
immediately after use.
To clean the chrome-plated surfaces use a soft
cloth, soap and warm water. Never use cleaning
agents that contain a corrosive acid or a scouring
additive.
CLEANING
Do not use any
sharp objects
to clean nozzles
Top Rail
Bracket
Bottom Rail
Bracket
Remove the protective cap from the showerhead
ball joint and screw the unit onto the overhead
arm ensuring the filter washer is in place.
This arm is not adjustable.
6.
Min 13±2mm
Max
/25mm
Water Inlet
Connector
WATER INLET: RECOMMENDED MINIMUM HEIGHT
OF 1800mm FROM FLOOR LEVEL
Install a ½" male threaded connection at the
recommended height on wall, ensuring that a
minimum of 13±2mm of thread protrudes past
the finished wall.
Correct water proong must be applied.
650mm
Rail Connector
Water Inlet
Connector
Make sure a washer is in both ends of the hose.
Screw hose onto lower outlet on rail, attach
handset and place firmly in holder. Tilt and rotate
head to the desired position.
Filter Washer
Ball Joint
2
1
7
3
8
4
9
5
10
6
11
Cleaning & Care
We recommend weekly cleaning with mild soapy water and a microfibre cloth. In highly polluted or coastal locations we recommend
cleaning 2-3 times per week. Please note that colour tapware requires more frequent cleaning than chrome tapware.
●Never use harsh detergents, citrus-based cleaners or abrasive cleaners, as these will
scratch the surface. Use of unsuitable cleaners may damage the surface and will not
be covered by warranty.
●Where your tapware remains dry in use, a non-abrasive soft cloth can be used to
remove surface dust.
●Use of wax-based furniture creams should be avoided as these can result in a build-up
of deposits which can effect the appearance.
●Do not use undue pressure and wipe in one direction only.
Installation
IMPORTANT:
●Before commencing installation, turn off the water supply. While not essential, we recommend fitting isolation valves to both the hot
and cold-water supply.
●Some showers may not provide an effective shower when used with gravity fed heated water systems or where pressures are less than
150kPa at the outlet. Additionally, showers with flow rates of less than 9L/min may not allow the following to function correctly:
- Some instantaneous water heaters
- Some tempering valves
- Some thermostatic mixing valves
●Some shower heads only operate correctly when hot and cold water supplies are both mains pressure and may not be suitable for some
instantaneous hot water services.
●When water pressure is in excess of 500kPa a pressure limiting device is required.
1. Recommended minimum height:
1800mm from floor level to top water
inlet position.
Install a ½" male threaded connection
at the appropriate height on wall,
ensuring that a minimum of 13±2mm
of thread protrudes past the finished
wall. Correct water proofing must
be applied.
2. Apply thread tape (or similar) to the
½" connection, then screw the rail
connector to the connection.
3. Screw the rail connector to a wall stud
making sure it is vertically in line with
the top rail connector.
Maximum centre distance between
the top and bottom shower
connections is 650mm.
4. Check the grub screws are wound
tight. Push the rail brackets onto the
top and bottom rail connectors until
they are against wall.
Secure with grub screws.
5. Remove the protective cap from the
showerhead ball joint and screw the
unit onto the overhead arm ensuring
the filter washer is in place.
This arm is not adjustable.
6. Make sure a washer is in both ends
of the hose. Screw hose onto lower
outlet on rail, attach handset and
place firmly in holder. Tilt and rotate
head to the desired position.
1Cup
2Joint
3Body
4Socket
5Joint
6Staright Pipe
7Hose
8Hand Shower
9Shower Head
10 Bend
11 Screw
FIENZA.COM.AU FIENZA.COM.AUItem Code: 455116 | Updated: 21/03/2023 Item Code: 455116 | Updated: 21/03/2023
INS TAL L ATI ON GUIDE INS TAL L ATI ON GUIDE
