FIC PA-2007 Manual de usuario

Installation Procedures

The PA-2007 has several user-adjustable jumpers on the board that allow you to

configure your system to suit your requirements. This chapter contains

information on the various jumper settings on your mainboard.

To set up your computer, you should follow these installation steps:

nStep 1 -

Set system jumpers Read this chapter for jumper settings.

nStep 2 -

Install RAM modules. Please consult Install RAM modules of the

English manual.

nStep 3 -

Install the CPU. Read this chapter for jumper settings.

nStep 4 -

Install expansion cards. Please consult Install expansion cards of

the English manual.

nStep 5 -

Connect cables and power supply. Please consult Connect cables

and power supply of the English manual.

nStep 6 -

Set up BIOS features. Please read Chapter Two of this manual.

CAUTION : If you use an electric drill to install this mainboard on your

chassis, please wear a static wrist strap. The recommended torque is from

5.0 to 8.0 kg/cm to avoid damaging the chips’ pins.

Chapter 1

PA-2007 Mainboard Manual

Setting the System Jumpers

Jumpers

Jumpers are used to select the operation modes for your system. Some jumpers

on the board have three metal pins with each pin representing a different

function. To set a jumper, a black cap containing metal contacts is placed over

the jumper pins according to the required configuration. A jumper is said to be

shorted when the black cap has been placed on one or two of its pins. The types

of jumpers used in this manual are shown below:

NOTE : Users are not encouraged to change the jumper settings not listed in

this manual. Changing the jumper settings improperly may adversely affect

system performance.

Clear Password: CPW

This jumper allows you to set the password configuration to Enabled or

Disabled. You may need to enable this jumper if you forget your password.

Installation Procedures

Flash ROM Type Selection: EP1, EP2

These two jumpers allow you to select the flash ROM type (1MB).

CPU to SRAM Data Transacting Mode Selection: SRAM

This jumper allows you to select the CPU-to-SRAM data read/write mode.

If you install a Cyrix or IBM processor on this mainboard, please set at 2-3 pin

pair and set the Linear Burst feature of Chipset Features Setup, Chapter 2.

PA-2007 Mainboard Manual

Installing the CPU

The CPU module resides in the Zero Insertion Force (ZIF) socket on the

mainboard. Follow the tables below to set the jumpers for your processor. For

specific jumpers settings for Intel Pentium® MMX, Pentium®, AMD-K5/K6

and Cyrix/IBM 6x86MX™/6x86™ processors, please consult the English

manual.

CPU External Clock (BUS) Frequency: CLK1, CLK2, CLK3

The table below shows the jumper settings for the different CPU speed

configurations.

Installation Procedures

CPU to Bus Frequency Ratio: FREQ1, FREQ2, FREQ3

These three jumpers are used in combination to decide the ratio of the internal

frequency of the CPU to the bus clock.

PA-2007 Mainboard Manual

This Page Intentionally Left Blank

Award BIOS Setup

The mainboard comes with the Award BIOS chip that contains the ROM Setup

information of your system. This chip serves as an interface between the

processor and the rest of the mainboard's components. This chapter explains the

information contained in the Setup program and tells you how to modify the

settings according to your system configuration.

CMOS Setup Utility

A Setup program, built into the system BIOS, is stored in the CMOS RAM that

allows the configuration settings to be changed. This program is executed when

the user changes system configuration; the user changes system backup battery;

or the system detects a configuration error and asks the user to run the Setup

program. At power-on RAM testing, the message Press DEL to enter Setup

appears. Use the arrow keys to select and press Enter to run the selected

program.

Chapter 2

PA-2007 Mainboard Manual

Standard CMOS Setup

The Standard CMOS Setup screen is displayed above. System BIOS

automatically detects memory size, thus no changes are necessary. It has a few

items for setting. Each item may have one or more option settings. It allows you

to change the system Date and Time, IDE hard disk, floppy disk drive types for

drive A: and B:, boot up video display mode, and POST error handling

selection. Use the arrow keys to highlight the item and then use the PgUp, or

PgDn keys to select the value you want in each item.

Hard Disk Configurations

TYPE:

Select from 1 to 45 to fill remaining fields with predefined values of disk

drives. Select User to fill the remaining fields. Select Auto to detect the

HDD type automatically.

SIZE:

The hard disk size. The unit is Mega Bytes.

CYLS:

The cylinder number of the hard disk.

Award BIOS Setup

HEAD:

The read/write head number of hard disk.

PRECOMP:

The cylinder number at which the disk drive changes the write timing.

LANDZ:

The cylinder number that the disk drive heads (read/write) are seated

when the disk drive is parked.

SECTOR:

The sector number of each track defined on the hard disk.

MODE:

Select Auto to detect the mode type automatically. If your hard disk supports

the LBA mode, select LBA or Large. However, if your hard disk cylinder is

more than 1024 and does not support the LBA function, you have to set at

Large. Select Normal if your hard disk supporting cylinders is below 1024.

Please read page 60 of this manaul for more information.

Software Turbo Speed

The BIOS supports Software Turbo Speed feature. Instead of pressing the

Turbo Speed Button on the front panel, simply press the Alt, Ctrl, and +

keys at the same time to enable the Turbo Speed feature; and press the Alt,

Ctrl, and - keys at the same time to disable the feature.

PA-2007 Mainboard Manual

BIOS Features Setup

Moving around the BIOS and Chipset Features (refer to the next section) Setup

programs shown above works the same way as moving around the Standard

CMOS Setup program. Users are not encouraged to run the BIOS and Chipset

Features Setup programs. Your system should have been fine-tuned before

shipping. Improper Setup may cause the system to fail, consult your dealer

before making any changes.

Virus Warning

When enabled, assigns the BIOS to monitor the master boot sector and the

DOS boot sector of the first hard disk drive.

The options are: Enabled, Disabled (Default).

CPU Internal Cache

When enbled, improves the system performance. Disable this item when

testing or trouble-shooting.

The options are: Enabled (Default), Disabled.

External Cache

When enabled, supports an optional cache SRAM.

The options are: Enabled (Default), Disabled.

Quick Power On Self Test

When enabled, allows the BIOS to bypass the extensive memory test.

The options are: Enabled, Disabled (Default).

Tabla de contenidos

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario