FIBARO FGPB-101 Manual de usuario

FIBARO BUTTON

FGPB-101

CONTENTS

#1: Description and features 4

#2: Basic activation 5

#3: Adding/removing the device 6

#4: Operating the device 7

#5: Associations 8

#6: Advanced parameters 9

#7: Specications 13

#8: Regulations 14

OPERATING

MANUAL EN

v1.2

DESCRIPTION AND FEATURES

Main features of FIBARO Button:

• Compatible with any Z-Wave or Z-Wave Plus Controller,

• Supports Z-Wave network Security Mode with AES-128 encryption,

• Completely wireless with battery power and Z-Wave

communication,

• May be installed anywhere in your home,

• Extremely easy installation - simply add and put on desired surface,

• Many colour variations: black, white, red, green, blue, yellow,

orange and brown.

FIBARO Button is a compact, battery-powered, Z-Wave Plus

compatible device. It allows you to control devices through the

Z-Wave network and run various scenes dened in FIBARO System.

Dierent actions may be triggered with one to ve clicks or by holding

the button down. In panic mode, each press of the button results in

triggering the FIBARO Alarm.

With its small design and wireless communication, the FIBARO Button

can be conveniently mounted on any surface and in any position or

location at home, e.g. beside the bed or under the desk.

#1: Description and features

FIBARO Button is a fully

compatible Z-Wave Plus device.

NOTE

This device may be

used with all de-

vices certied with

the Z-Wave Plus cer-

ticate and should be

compatible with such

devices produced by

other manufacturers.

NOTE

Z-Wave Controller

must support Z-Wave

Security Mode in

order to fully utilize the

product.

BASIC ACTIVATION

#2: Basic activation

1. Press and turn the button counter-clockwise to open the casing.

2. Remove the paper strip underneath the battery.

3. Press and turn the button clockwise to close the casing.

4. Place the device within the direct range of your Z-Wave controller.

5. Set the main controller in (security/non-security) add mode (see

the controller’s manual).

6. Click the button 6 times at least.

7. Wait for the device to be added into the system, successful adding

will be conrmed by the controller.

8. Install the device in desired location using the attached

self-adhesive pad.

9. Click the button 4 times to wake it up.

ADDING/REMOVING THE DEVICE

Adding (Inclusion) - Z-Wave device learning mode, allowing to add

the device to existing Z-Wave network.

To add the device to the Z-Wave network:

1. Place the Button within the direct range of your Z-Wave controller.

2. Set the main controller in (Security/non-Security) add mode (see

the controller’s manual).

3. Click the Button at least six times.

4. Wait for the adding process to end.

5. Successful adding will be conrmed by the Z-Wave controller’s

message.

Removing (Exclusion) - Z-Wave device learning mode, allowing to

remove the device from existing Z-Wave network.

To remove the device to the Z-Wave network:

1. Place the Button within the direct range of your Z-Wave controller.

2. Set the main controller in remove mode (see the controller’s

manual).

3. Click the Button at least six times.

4. Wait for the removing process to end.

5. Successful removing will be conrmed by the Z-Wave controller’s

message.

#3: Adding/removing the device

NOTE

Adding in Security

Mode must be per-

formed up to 2 meters

from the controller.

NOTE

Removing the Button

from the Z-Wave net-

work restores all the

default parameters of

the device.

NOTE

In case the device is

not added, repeat the

adding procedure.

OPERATING THE DEVICE

#4: Operating the device

Waking up the device:

The Button needs to be woken up to receive information about the

new conguration from the controller, like parameters and associa-

tions.

Click the Button 4 times to wake it up.

Operating the Button:

1 click:

2 clicks:

3 clicks:

4 clicks:

5 clicks:

6 or more

clicks:

Hold:

Release:

send action to associated devices (switch on/o by de-

fault) and/or trigger a scene

send action to associated devices (switch on maximum

level by default) and/or trigger a scene

send action to associated devices (no action by default)

and/or trigger a scene

wake the device up and/or trigger a scene

start reset procedure (press and hold for 5s to conrm)

and/or trigger a scene

learning mode (adding/removing)

send action to associated devices (start level change up/

down) and/or trigger a scene

send action to associated devices (stop level change)

and/or trigger a scene

Scene ID:

Every action with the

Button is send to the main

controller with Scene ID

equal to 1. Controller recog-

nizes type of action using the

attribute assigned to it.

Reset procedure of the Button:

Reset procedure allows to restore the device back to its factory set-

tings, which means all information about the Z-Wave controller and

user conguration will be deleted. In order to reset the device:

1. Click the Button exactly ve times.

2. Press and hold the Button for at least 5 seconds.

Action Attribute

1 click Key Pressed 1 time

2 clicks Key Pressed 2 times

3 clicks Key Pressed 3 times

4 clicks Key Pressed 4 times

5 clicks Key Pressed 5 times

Hold Key Held Down

Release Key Released

NOTE

If notications are

enabled, each press

of the button results

in sendng a com-

mand (Notication

Type=HOME_SECURI-

TY, Event=Intrusion,

Unknown Location).

NOTE

Resetting the device is

not the recommend-

ed way of removing

the device from the

Z-Wave network. Use

reset procedure only

if the primary con-

troller is missing or

inoperable. Certain

device removal can be

achieved by the pro-

cedure of removing.

ASSOCIATIONS

#5: Associations

The Button provides the association of four groups:

1st association group – “Lifeline” reports the device status and al-

lows for assigning single device only (main controller by default).

2nd association group – “On/O” is assigned to clicking the button

and is used to turn on/o associated devices.

3rd association group – “Dimmer” is assigned to holding the but-

ton and is used to change level of associated devices.

4th association group –“Alarm“ is assigned to clicking and/or hold-

ing the button (triggers are dened in parameter 30) and is used to

send alarm frames to associated devices.

To add an association (using the Home Center controller):

1. Go to device options by clicking the icon:

2. Select the„Advanced” tab.

3. Click the “Setting Association” button.

4. Specify to which group and what devices are to be associated.

5. Save the changes.

6. Wake up the device manually to conrm changes (4 clicks).

FIBARO Button in 2nd, 3rd and 4th group allows to control 5 regular

or multichannel devices per an association group, with the exception

of “LifeLine” that is reserved solely for the controller and hence only 1

node can be assigned.

It is not recommended to associate more than 10 devices in general,

as the response time to control commands depends on the number of

associated devices. In extreme cases, system response may be delayed.

Association (linking devices) - direct control of other devices within

the Z-Wave system network e.g. Dimmer, Relay Switch, Roller Shutter

or scene (may be controlled only through a Z-Wave controller).

NOTE

Association ensures

direct transfer of

control commands

between devices, is

performed without

participation of the

main controller and

requires associated

device to be in the di-

rect range.

NOTE

Increasing number

of associations will

increase battery con-

sumption resulting in

shorter battery life.

NOTE

The device supports

the generic Z-Wave

command class "Basic"

but will ignore any SET

or GET commands and

will not respond with a

Basic Report.

ADVANCED PARAMETERS

#6: Advanced parameters

1. Scenes sent to the controller

This parameter determines which actions result in sending scene IDs

and attributes assigned to them.

Available settings: 1- Key Pressed 1 time

2- Key Pressed 2 times

4- Key Pressed 3 times

8- Key Pressed 4 times

16 - Key Pressed 5 times

32 - Key Held Down

64 - Key Released

Default setting: 127 (all) Parameter size: 1[byte]

The Button allows to customize its operation to user’s needs. The set-

tings are available in the FIBARO interface as simple options that may

be chosen by selecting the appropriate box.

In order to congure the Button (using the HC controller):

1. Go to the device options by clicking the icon:

2. Select the„Advanced” tab.

3. Modify values of chosen parameters.

4. Save the changes.

5. Wake up the device manually to conrm changes (4 clicks).

Wake up interval

Available settings: 0or 3600-64800 (in seconds, 1h - 18h)

Default setting: 0

The Button will wake up at each dened time interval and always try to

connect with the main controller. After successful communication at-

tempt, the device will update conguration parameters, associations

and settings and then will go into Z-Wave communication standby.

After failed communication attempt (eg. no Z-Wave range) the device

will go into Z-Wave communication standby and retry to establish

connection with the main controller after the next time interval.

Setting wake up interval to 0 disables sending Wake Up notication

to the controller automatically. Wake up may be still performed man-

ually by clicking the Button 4 times.

NOTE

Values of parameter

1 may be combined,

e.g. 1+2=3 means that

scenes will be sent

after pressing the but-

ton once or twice.

NOTE

Longer wake up time

interval means less

frequent communica-

tion and thus a longer

battery life.

ADVANCED PARAMETERS

NOTE

Setting parameters

11, 13, 15, 21, 23 and

25 to appropriate val-

ue will result in:

1-99 - forcing level of

associated devices

255 - setting associat-

ed devices to the last

remembered state or

turning them on

3. Associations in Z-Wave network Security Mode

This parameter denes how commands are sent in specied associa-

tion groups: as secure or non-secure. Parameter is active only in Z-Wave

network Security Mode. It does not apply to 1st„Lifeline”group.

Available settings: 1- 2nd group sent as secure

2- 3rd group sent as secure

4- 4th group sent as secure

Default setting: 7 (all) Parameter size: 1[byte]

10. Key Pressed 1 time – command sent to 2nd association group

This parameter denes commands sent to devices associated in 2nd

association group after a single click.

Available settings: 0- no action

1- SWITCH ON

2- SWITCH OFF

3- SWITCH ON/OFF – alternately

Default setting: 3Parameter size: 1[byte]

11. Key Pressed 1 time – value of SWITCH ON command sent to

2nd association group

This parameter denes value of SWITCH ON command sent to devices

in 2nd association group after a single click.

Available settings: 1-255 - sent value

Default setting: 255 Parameter size: 2[bytes]

12. Key Pressed 2 times – command sent to 2nd association group

This parameter denes commands sent to devices associated in 2nd

association group after a double click.

Available settings: 0- no action

1- SWITCH ON

2- SWITCH OFF

3- SWITCH ON/OFF – alternately

Default setting: 1Parameter size: 1[byte]

13. Key Pressed 2 times – value of SWITCH ON command sent to

2nd association group

This parameter denes value of SWITCH ON command sent to devices

in 2nd association group after a double click.

Available settings: 1-255 - sent value

Default setting: 99 Parameter size: 2[bytes]

NOTE

Values of parameter

3 may be combined,

e.g. 1+2=3 means that

2nd & 3rd group are

sent as secure.

ADVANCED PARAMETERS

14. Key Pressed 3 times – command sent to 2nd association group

This parameter denes commands sent to devices associated in 2nd

association group after a triple click.

Available settings: 0- no action

1- SWITCH ON

2- SWITCH OFF

3- SWITCH ON/OFF – alternately

Default setting: 0Parameter size: 1[byte]

15. Key Pressed 3 times – value of SWITCH ON command sent to

2nd association group

This parameter denes value of SWITCH ON command sent to devices

in 2nd association group after a triple click.

Available settings: 1-255 - sent value

Default setting: 255 Parameter size: 2[bytes]

20. Key Pressed 1 time – command sent to 3rd association group

This parameter denes commands sent to devices associated in 3rd

association group after a single click.

Available settings: 0- no action

1- SWITCH ON

2- SWITCH OFF

3- SWITCH ON/OFF – alternately

Default setting: 3Parameter size: 1[byte]

21. Key Pressed 1 time – value of SWITCH ON command sent to

3rd association group

This parameter denes value of SWITCH ON command sent to devices

in 3rd association group after a single click.

Available settings: 1-255 - sent value

Default setting: 255 Parameter size: 2[bytes]

22. Key Pressed 2 times – command sent to 3rd association group

This parameter denes commands sent to devices associated in 3rd

association group after a double click.

Available settings: 0- no action

1- SWITCH ON

2- SWITCH OFF

3- SWITCH ON/OFF – alternately

Default setting: 1Parameter size: 1[byte]

ADVANCED PARAMETERS

23. Key Pressed 2 times – value of SWITCH ON command sent to

3rd association group

This parameter denes value of SWITCH ON command sent to devices

in 3rd association group after a double click.

Available settings: 1-255 - sent value

Default setting: 99 Parameter size: 2[bytes]

24. Key Pressed 3 times – command sent to 3rd association group

This parameter denes commands sent to devices associated in 3rd

association group after a triple click.

Available settings: 0- no action

1- SWITCH ON

2- SWITCH OFF

3- SWITCH ON/OFF – alternately

Default setting: 0Parameter size: 1[byte]

25. Key Pressed 3 times – value of SWITCH ON command sent to

3rd association group

This parameter denes value of SWITCH ON command sent to devices

in 3rd association group after a triple click.

Available settings: 1-255 - sent value

Default setting: 255 Parameter size: 2[bytes]

29. Key Held Down – command sent to 3rd association group

This parameter denes commands sent to devices associated in 3rd

association group after holding the button down.

Available settings: 0- no action

1- START LEVEL CHANGE UP (brightening)

2- START LEVEL CHANGE DOWN (dimming)

3- START LEVEL CHANGE UP/DOWN (brighten-

ing/dimming) – alternately

Default setting: 3Parameter size: 1[byte]

30. Alarm frame triggers

Parameter determines which actions result in sending alarm frames

to 4th association group.

Available settings: 1- Key Pressed 1 time

2- Key Pressed 2 times

4- Key Pressed 3 times

8- Key Pressed 4 times

16 - Key Pressed 5 times

32 - Key Held Down

64 - Key Released

Default setting: 127 (all) Parameter size: 1[byte]

NOTE

Values of parame-

ter 30 may be com-

bined, e.g. 1+2=3

means that alarm

frames will be sent

after pressing the but-

ton once or twice.

Otros manuales para FGPB-101

Tabla de contenidos

Otros manuales de Controladores de FIBARO

FIBARO

FIBARO WALLI FGWCEU-201 Manual de usuario

FIBARO

FIBARO ROLLER SHUTTER 2 Manual de usuario

FIBARO

FIBARO SWIPE FGGC-001 Manual de usuario

FIBARO

FIBARO THE BUTTON Manual de usuario

FIBARO

FIBARO FIBEFGWCEU-201-B Manual de usuario

FIBARO

FIBARO FGS-214 Manual de usuario

FIBARO

FIBARO KEYFOB FGKF-601 Manual de usuario

FIBARO

FIBARO RGBW Controller Manual de usuario

FIBARO

FIBARO FGBHRGBW-041-1 Manual de usuario

FIBARO

FIBARO FGRGBW-442 Manual de usuario

FIBARO

FIBARO FGPB-101 Manual de usuario

FIBARO

FIBARO FGPB-101-5 Manual de usuario

FIBARO

FIBARO RGBW CONTROLLER 2 Manual de usuario

FIBARO

FIBARO SWIPE FGGC-001 Manual de usuario

FIBARO

FIBARO ROLLER SHUTTER 2 Manual de usuario

FIBARO

FIBARO FGPB-101 Manual de usuario

FIBARO

FIBARO ROLLER SHUTTER 3 Manual de usuario

FIBARO

FIBARO FGRGBWM-441 Manual de usuario

FIBARO

FIBARO Home Center Lite Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario