Festool VS-600 Manual

Page 1 of 5 www.festool-usa.com

VS600 Jointing System — Procedure for Half Blind Dovetails

A Step by Step Procedure for these templates: SZ14 and SZ20

Template SZ14 - Half Blind Dovetail

for wood thickness .63 - .79" (26-20mm)*

Cutters: 490 991 (HSS); 490 990 (carbide)

Template SZ20 - Half Blind Dovetail

for wood thickness .63 - .79" (26-20mm)*

Cutters: 490 991 (HSS); 490 990 (carbide)

* wood thickness measurements refer to front/back

piece only - sides can be thinner.

Install the copying ring. The ring should be the

one that came with the SZ14 or SZ20

template or one that fits in the template

grooves exactly.

Install the appropriate bit in the router.

Cutters: 490 991 (HSS)

490 990 (carbide)

Page 2 of 5 www.festool-usa.com

Install SZ14 Template. Before tightening

locking knobs, be sure the alignment shoulders

on underside are touching the base.

Rotate end stops so that SZ14 is pointing to

wood edge.

I lower the template and adjust the two black

positioners so they are in the "D" window.

I move the black positioner left and right until

the arrows are touching the flat side of the "D"

and lock it in that place.

Page 3 of 5 www.festool-usa.com

This is the drawing from the Manual. You

should mark the pieces of your box

accordingly.

I have laid out the test drawer and have

numbered everything the exact same way.

Position the front/back piece in the horizontal

clamp with insides facing up. The "A"

corners will be on the left; the "B" on the right.

Position the sidepiece with the inside edge

facing front and touching the underside of the

template.

Make sure the front/back piece is touching the

backside of the sidepiece end.

Page 4 of 5 www.festool-usa.com

Zero router by placing it on the template and

plunge the bit until it "kisses" the top of the

wood. Lock the plunge.

Move the plunge rod to the 12mm position.

This is the recommended start depth for use

with this template.

I move the router over where it is still on the

template but no wood is beneath. I plunge to

the preset point and lock the plunge setting.

I also adjust the dust hood so that it allows

free movement of the router on the template

— including room to cut the tails.

Page 5 of 5 www.festool-usa.com

It doesn't take long to run the router for both

the "A" and "B" joints. I have made a very

light pass from right to left (climb cut) — this

will reduce tear out. Then, guide the router

into each of the fingers.

Test fit the pieces. They are exact. I did spray

paint the "A" front side for a contrast —

otherwise, these photos are unretouched.

This template can do great drawers. At the

right, the front joint is with 3/4" front and 3/4"

sides. Since many cabinets have drawers with

1/2" sides and 3/4" fronts, the upper example

is just that and did not require any change to

the set-up.

It can even do 1/2-blind dovetails with a

rabbet front.

Otros manuales para VS-600

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Festool

Festool

Festool Carvex PSC 400 EB Instrucciones de instalación

Festool

Festool OFK 700 EQ Manual de usuario

Festool

Festool MFK 700 EQ Manual de usuario

Festool

Festool Carvex PS 420 EBQ Manual de usuario

Festool

Festool OF 2200 EB Manual de usuario

Festool

Festool VECTURO OS 400 EQ Instrucciones de instalación

Festool

Festool Carvex PSC 400 EB Manual de usuario

Festool

Festool VECTURO OS 400 E Instrucciones de instalación

Festool

Festool Domino XL DF 700 EQ Instrucciones de instalación

Festool

Festool Duplex LS 130 EQ Instrucciones de instalación

Festool

Festool Trion PS-300Q Guía

Festool

Festool Domino DF 500 Manual de usuario

Festool

Festool ROTEX RO 90 DX FEQ Manual de usuario

Festool

Festool OFK 500 Q Manual de usuario

Festool

Festool OF 1400 EB Instrucciones de instalación

Festool

Festool PSC 420 EB Instrucciones de instalación

Festool

Festool Carvex PSC 400 EB Manual de usuario

Festool

Festool CARVEX PSBC 420 Instrucciones de instalación

Festool

Festool OFK 700 EQ Manual de usuario

Festool

Festool ETS EC 125/3 EQ Manual de usuario

Festool

Festool RAS 180.03 E-HR Manual de usuario

Festool

Festool TPE-RS 100 Q Instrucciones de instalación

Festool

Festool Domino DF 500 Manual del propietario

Festool

Festool BHC 18 Instrucciones de instalación

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual