Festo Bionic Fish Manual de usuario
Bionic Fish
Assembly Instructions
FestoAG&Co.KGFesto DidacticSE
2
Equipment and Supplies
Required items from the Bionics Kit and/or Materials Pack:
1. Tail fin (large) assembled and attached to the plastic component (with cutouts) –see ‘Start Here’ for tail fin assembly instructions
2. Tail fin (small) assembled –2
3. Transparent corpus (body)
4. Small, waterproof servo motor (marked with a sticker)
5. Connecting element
6. Cable ties
7. Sealing rings –2
8. Tube (clear)
9. Electronic board with microcontroller
10. Material for fish tail and body (plastic poster board)
1
2
3
8
4
7
9
6
5
10
FestoAG&Co.KGFesto DidacticSE
3
Equipment and Supplies, continued
Additionally required:
1. Water basin
2. 4-AA batteries
3. Scissors
4. Items to balance the fish (nuts, bolts, coins, etc.)
5. Phillips head screwdriver
1
2
3
4
5
FestoAG&Co.KGFesto DidacticSE
4
If the tail fins have been previously assembled, please go directly to the Instructions on the next page.
Tail Fin Assembly
From the Bionics Kit, locate the bag containing the tools and 2 screws (used in Step 3). Next, locate the bags
containing the small screws and nuts (long and short) and the plastic support pieces (large and small).
To assemble the large tail fin, attach the large support pieces to the inside of the fin using the longer screws, nuts,
and tools.
Locate the plastic component (with cutouts). Place the opening on the base of the assembled large tail fin over the
post on the plastic component. Align the screw holes and connect the pieces together using the 2 screws and a
screwdriver.
Assemble the small fins using the small support pieces, the shorter
screws, nuts, and tools.
Start Here
1
2
4
3
FestoAG&Co.KGFesto DidacticSE
5
Instructions
Required items: 2 sealing rings, connecting element
Place the two sealing rings on each end of the connecting element.
Required items: assembled tail fin (large)
Attach the large tail fin to one side of the connecting element. Twist to lock it in place.
1
2
FestoAG&Co.KGFesto DidacticSE
6
Required items: clear tube
Attach the clear tube to the opening of the large tail fin. The top of the clear tube should
be at approximately the same level as the third support piece from the bottom of the fin.
If needed, cut the tube with scissors to the appropriate length.
Required items: small, waterproof servo motor
Attach the waterproof servo motor to the holder on the large tail fin, such that the rudder
horn of the motor points downwards. Guide the cable of the servo motor through the
clear tube.
3
4
FestoAG&Co.KGFesto DidacticSE
7
Required items: 1 cable tie
While holding the clear tube against the servo motor, connect it to the large tail fin with a
cable tie. Shorten the cable tie, if necessary.
5
FestoAG&Co.KGFesto DidacticSE
8
Required items: 4 cable ties
Connect the large tail fin to the rudder horns of the servo motor using 2 cable ties. Pull
the cable ties through the two small tabs of the fin and then through the openings of the
rudder horn in a crisscross fashion. The two cable ties cross above the fin. Add 2 more
cable ties to act as stopper.
Testing
Carefully move the rudder horn back and forth with your finger to check the tension of the
cable ties. If the fin does not move evenly, the length or the tension of the cable ties may
have to be corrected.
6
7
Shorten the cable ties, if
necessary.
FestoAG&Co.KGFesto DidacticSE
9
Required items: electronic board with microcontroller, 4 AA batteries
Insert the batteries, 2 on each side of the electronic board with microcontroller.
Required items: electronic board with microcontroller, small waterproof servo motor
Insert the plug of the servo motor into one of the electronics board’s set of pins.
8
9
FestoAG&Co.KGFesto DidacticSE
10
Required items: transparent corpus (body)
Insert the electronics board with microcontroller into the transparent corpus (body) and
slide it into the rail located inside. Turn the switch “on”. The small light on the electronics
board turns on.
Required items: tail fin (large)
Attach the connecting element onto the transparent corpus (body). Twist to lock it into
place.
10
11
Tabla de contenidos
Otros manuales de Robótica de Festo
Festo
Festo EHPS A-RA1 Series Manual de usuario
Festo
Festo CP Factory Manual de usuario
Festo
Festo MPS Station Manual de usuario
Festo
Festo CP Factory Manual de usuario
Festo
Festo Bionic Elephant Trunk Manual de usuario
Festo
Festo Robotino 4.0 Manual de usuario
Festo
Festo Robotino Manual de usuario
Festo
Festo Chameleon Tongue Manual de usuario
Manuales populares de Robótica de otras marcas
STEMCenter USA
STEMCenter USA Pi-Bot v2.00 Manual de usuario
SunFounder
SunFounder PiDog Manual de usuario
Universal Robots
Universal Robots UR5 Manual de usuario
Universal Robots
Universal Robots E Series Manual de usuario
YASKAWA
YASKAWA MOTOMAN-MPL80 II Manual de usuario
EFORT
EFORT ECR5 Manual de instrucciones
