Festo CPX-E DO Series Manual de usuario

8126685

CPX-E-...DO-...

Digital output module

8126685

2020-01a

[8126687]

Description| Function,

Parameterisation

Translation of the original instructions

2 Festo — CPX-E-...DO-... — 2020-01a

3Festo — CPX-E-...DO-... — 2020-01a

1 About this Document................................................................................................... 4

1.1 Further applicable documents...................................................................................... 4

1.2 Target group................................................................................................................. 4

1.3 Product version............................................................................................................ 4

1.4 Product labelling.......................................................................................................... 5

1.5 Specified standards...................................................................................................... 5

1.6 UL/CSA Certification..................................................................................................... 5

2 Function........................................................................................................................6

2.1 General..........................................................................................................................6

2.1.1 Product design........................................................................................................7

2.1.2 Display components............................................................................................... 7

2.1.3 Connecting components......................................................................................... 7

2.2 Diagnostics................................................................................................................... 8

3 Parameterisation......................................................................................................... 10

3.1 Overview of parameters................................................................................................ 10

3.2 Module parameters...................................................................................................... 10

3.2.1 Diagnostics of short circuit at output...................................................................... 10

3.2.2 Diagnostics of undervoltage in load supply............................................................ 11

3.2.3 Behaviour after SCO............................................................................................... 11

4 Technical Data............................................................................................................. 12

Table of contents

1 About this Document

This document describes the function and parameterisation of the product stated in the title. Safe use

of the product is described in a separate document è 1.1 Further applicable documents.

1.1 Further applicable documents

All available documents for the product èwww.festo.com/pk.

Documentation Contents

Description of the automation system CPX-E

(CPX-E-SYS)

Detailed description of the

automation system CPX-E

Instruction manual for automation system CPX-E

(CPX-E-SYS)

Instruction manual and important information on

assembly, electrical installation and maintenance

tasks for an automation system CPX-E

Instruction manual digital output module

CPX-E-...DO-... (CPX-E-...DO-...)

Instruction manual and important information on

use and safe application

Documentation of the components in an

automation system CPX-E and the connected

peripherals

Information on using the components

Operating conditions| EX Information on the use of the product in poten-

tially explosive gas atmospheres

Documentation for the higher-order controller

and the additional participants in the network

Information on commissioning and parameterisa-

tion of the components

Tab. 1 Further applicable documents

1.2 Target group

This document is intended for qualified personnel. Experience with electrical control systems is

required in order to understand this documentation.

1.3 Product version

This document refers to the following product versions:

Product Version

CPX-E-8DO Digital output module CPX-E-8DO, revision1 or later

CPX-E-8DO-EX1E1) Digital output module CPX-E-8DO-EX1E, revision1 or later

1) Use in an industrial environment and in process automation according to NE21 and in potentially explosive atmospheres

Tab. 2 Product version

The product version can be identified from the product labelling or with the help of appropriate soft-

ware from Festo.

About this Document

Festo — CPX-E-...DO-... — 2020-01a4

Appropriate software for determining the product version can be found in the Festo Support Portal

èwww.festo.com/sp.

Information on using the software can be found in the integrated Help function.

There may be an updated version of this document for these or later product versions

èwww.festo.com/sp.

1.4 Product labelling

The product labelling is located on the left-hand side of the module. Scanning the printed Data Matrix

Code with an appropriate device opens the Festo Support Portal, with the information appropriate for

the product. Alternatively, the Product Key (11-digit alphanumeric code on the product labelling) can

be entered in the search field of the Support Portal èwww.festo.com/sp.

1Designation

2Revision version

3Pin allocation

4Approvals/warning symbols

5Product key

6Data Matrix Code

7Part number/serial number

Fig. 1 Product labelling

1.5 Specified standards

Version status

EN60529:2013-10 IEC60204-1:2014-10

EN61000-6-2:2005-08 IEC61131-2:2015-05

EN61000-6-4:2007-01 NE21:2012-05

Tab. 3 Standards specified in the document

1.6 UL/CSA Certification

In combination with the UL inspection mark on the product, the information in this section must also

be observed in order to comply with the certification conditions of Underwriters Laboratories Inc. (UL)

for USA and Canada.

About this Document

5Festo — CPX-E-...DO-... — 2020-01a

UL certification information

Product category code NRAQ/NRAQ7

File number E239998

Considered standards UL 61010-1, 3rd Edition, May 11, 2012, revised April 29, 2016

CAN/CSA-C22.2 No. 61010-1-12, 3rd Edition, revision dated April

29, 2016

UL 61010-2-201, 1st Edition, revised February 20, 2017

CSA-C22.2 No. 61010-2-201: 14, 1st Edition, issue date January

01, 2014

UL mark

Tab. 4 UL/CSA Certification Information

– Technical data and environmental conditions may be subject to change in order to comply with

Underwriters Laboratories Inc. (UL) certification requirements for the USA and Canada.

Observe deviations èTechnical data.

– The unit shall be supplied by a power source which fulfils the requirements on a limited-energy

circuit in accordance to IEC/EN/UL/CSA 61010-1 or on a Limited Power Source (LPS) in accord-

ance to IEC/EN/UL/CSA 60950-1 or IEC/EN/UL/CSA 62368-1 or a Class 2 circuit in accordance to

NEC or CEC.

2 Function

2.1 General

A digital output module provides digital outputs to connect electrical consumers. Valves, contactors or

display components, for example, can therefore be actuated with a voltage of 24VDC. Status and

error messages can be shown by LED indicators on the module. The module behaviour can be set

using parameters è 3 Parameterisation.

The power supply of the outputs is electronically protected from short circuit or overload. If this fuse is

tripped, the power supply of the output is switched off and the error is shown by an LED on the mod-

ule.

After the elimination of the short circuit or the overload, the power supply is not switched on again

until after the output is reset (default). This behaviour can be adjusted by parameters. The power sup-

ply of this output is then reactivated automatically without requiring reset of the output.

The electronic fuse of the module is slow-blowing. Electrical consumers with a temporarily higher cur-

rent requirement can therefore also be connected.

Function

6 Festo — CPX-E-...DO-... — 2020-01a

2.1.1 Product design

1LED indicators

2Output terminal strips [X0] … [X3]

3Load power supply terminal strip U OUT [XD]

4Terminal strip interlock

5Linking element

Fig. 2 Product design

2.1.2 Display components

1Module error [P] (red)

2Output channel error 0 … 7 (red)

– Output 0 [X0.0]

– Output 1 [X0.1]

– Output 2 [X1.0]

– …

3Status of output 0 … 7 (yellow)

– Output 0 [X0.0]

– Output 1 [X0.1]

– Output 2 [X1.0]

– …

4Load power supply UOUT [PL] (green)

Fig. 3 LED indicators

2.1.3 Connecting components

Connection [X0]…[X3] Signal

0 +24VDC output 0, 2, 4,…

1 +24VDC output 1, 3, 5,…

2 0VDC output 0, 2, 4,…

3 0VDC output 1, 3, 5,…

Tab. 5 Connection [X0] ... [X3]

Function

7Festo — CPX-E-...DO-... — 2020-01a

Port [XD]1) Signal

+24VDC load voltage supply UOUT

0VDC load voltage supply UOUT

1) The ports XD.0 and XD.1 and also XD.2 and XD.3, are interconnected in the terminal strip.

Tab. 6 Connection [XD]

2.2 Diagnostics

Various options are available for diagnosing errors:

– Internal system diagnostics

– LED indicators on the product

The internal system diagnostics is described in the “Description of automation system CPX-E”

è 1.1 Further applicable documents.

The LED indicators on the product are described in the following tables.

Module error [P]1)

LED

(red)

Meaning Remedy

Short circuit/overload at the output or mod-

ule defective

Check the connected actuators, eliminate

short circuit/overload.

Reset the “Behaviour after SCO” parameter

and then set it again.

The necessity of performing this step

depends on the configuration of the para-

meter “Behaviour after SCO”

è 3.2.3 Behaviour after SCO

Load power supply UOUT not present or

undervoltage

Check load power supplyOUT.

Off

Normal operating status –

1) flashes once briefly during initialisation of the automation system CPX-E.

Tab. 7 Module error

Function

8 Festo — CPX-E-...DO-... — 2020-01a

Output channel error [X0.0], [X0.1], [X1.0],…

LED

(red)

Meaning Remedy

Short circuit/overload at output è Module error

Off

No channel error –

Tab. 8 Output channel error [X0.0], [X0.1], [X1.0], ...

Status of output [X0.0], [X0.1], [X1.0],…

LED

(yellow)

Meaning Remedy

Output active (logic1)

Output sends 1-signal

–

Off

Output inactive (logic0)

Output sends 0-signal

–

Tab. 9 Status of output [X0.0], [X0.1], [X1.0], ...

Load power supply UOUT [PL]

LED

(green)

Meaning Remedy

Lit

Load power supplyOUT present –

Off

Load voltage supply UOUT not present or

undervoltage

Check load power supplyOUT.

Tab. 10 Load power supply [PL]

Function

9Festo — CPX-E-...DO-... — 2020-01a

3 Parameterisation

3.1 Overview of parameters

Module parameters are available to adapt the module to the operating situation. General settings that

affect the entire module are made using these parameters.

Module parameters Function number 1) Detailed information

Diagnostics of short circuit at output è Tab. 12

Diagnostics of undervoltage in load supply

4828 + 64m + 0

è Tab. 13

Behaviour after SCO 4828 + 64m + 1 è Tab. 14

Reserved 4828 + 64m + 2…7 –

1) Function number (èDescription of automation system CPX-E); m = module number (counted from left to right, starting from 0)

Tab. 11 Overview of module parameters

3.2 Module parameters

3.2.1 Diagnostics of short circuit at output

The "Diagnostics of short circuit at output" parameter defines whether the diagnostics of the outputs

in regard to short circuit or overload should be activated or deactivated.

When the diagnostics are activated, the error will be sent to the bus module and displayed on the

module by the error LED.

Module parameter – Diagnostics of short circuit at output

Selection via parameter

Bit

Setting Selection via software

F no.1)

4828 +

64m 76543210

Deactivate diagnostics No diagnostics + 0 0

Activate diagnostics Diagnostics (default) + 0 1

1) Function number (èDescription of automation system CPX-E); m = module number (counted from left to right, starting from 0)

Tab. 12

Parameterisation

10 Festo — CPX-E-...DO-... — 2020-01a

Tabla de contenidos

Otros manuales de Sistema de E/S de Festo

Festo

Festo SPC200-2AI-U Manual de lista de piezas

Festo

Festo CPX-E AI-U-I Series Manual de lista de piezas

Festo

Festo CP-FB11-E Manual de lista de piezas

Festo

Festo 03-FB-8 Series Manual de usuario

Festo

Festo VIGE-03-FB Series Instrucciones de funcionamiento e instalación

Festo

Festo CPX-F8DE-P Manual de lista de piezas

Festo

Festo CPX-E-4IOL-P Manual de usuario

Festo

Festo CPX-4AE-4AA-H Manual de usuario

Festo

Festo CPX-AP-I-8DI-M8-3P Manual de usuario

Festo

Festo CPX-FB33 Guía de referencia

Festo

Festo CPX-AP-I-4DI4DO-M12-5P Manual de lista de piezas

Festo

Festo CPX-AP-I-4AI-U-I-RTD-M12 Manual de lista de piezas

Festo

Festo CP-E08-M12-CL Manual de usuario

Festo

Festo CPX-E-4IOL Manual de usuario

Festo

Festo CPX-2ZE2DA Manual de usuario

Festo

Festo CPX-AP-I-4DI4DO-M8-3P Manual de lista de piezas

Festo

Festo CP-E16...M Series Manual de usuario

Festo

Festo CPX Series Manual de usuario

Festo

Festo CPX Series Manual de usuario

Festo

Festo CP-FB13-E Manual de lista de piezas

Festo

Festo CPX-E- DI Series Manual de usuario

Festo

Festo CPX-AP-I-4DI-M8-3P Manual de usuario

Festo

Festo SPC200-DIO Manual de usuario

Festo

Festo CPX-E- DI Series Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario