Fenwal Controls FC1 Guía del administrador

Page

ＣｏｎｔｒｏｌＵｎｉｔ

ＦＣ１

Operation Instruction Manual

Thank you for purchasing this product.

In this manual, we have shown the important notice in order for you to use the

device just and the method of handling this system.

In addition to you read this manual well before the utilization, understanding

well, and use.

fter you read, in the place where it is seen with anytime, please be sure to

keep.

ES0911 K5

730110 K0

ES0911

Page

Table of contents

１. Safety instructions.................................................................... 3

２. Installation........................................................................... 5

２.２. Installation of control unit...................................................... 6

２.３. Installation of detector.......................................................... 7

２.４. Wiring............................................................................ 8

３. Starting the system.................................................................... 9

３.２. Control unit..................................................................... 10

３.３. Dimensions....................................................................... 16

３.４. Electric specifications.......................................................... 17

３.５. Environmental specifications..................................................... 19

３.６. Mechanical specifications........................................................ 19

４. Procedures/steps to be taken in the event of alarm occurrence ......................... 20

４.１. Alarm............................................................................ 20

４.２. Zone Alarm...................................................................... 20

５. Indication of the time of trouble..................................................... 21

６. Procedures/steps to be taken in the event of trouble occurrence ....................... 22

７. Detector.............................................................................. 23

７.１. Connectable detector............................................................. 23

８. Serial communication facility......................................................... 24

９. Maintenance and Inspection............................................................ 25

９.１. Daily Inspection................................................................. 25

９.２. Periodically Inspection.......................................................... 26

９.３. Functional Inspection............................................................ 28

１０. Disposal............................................................................ 30

１１. Support............................................................................. 30

730110 K0

ES0911

Page

１

１１

１.

Safety instructions

Safety instructionsSafety instructions

Safety instructions

・ Before the using, read this chapter and use correctly.

・ The contents which it occurs when you handle erroneously are divided in two of “warning”

and “caution”. This division states clearly the size and impendence of the harm and the

damage.

・ Please keep below rules for safety.

！

！！

！

Warning

･Do not disassemble a control unit. It causes trouble.

･Do not remove a control unit and detector, Fire can not detect.

･

Do not use a control unit which has impacted. And also do not paint

a control unit.

･

Do not soak a control unit in water, and do not put a control unit

into water. It causes electric shock.

･

Do not use the method that not listed in this manual, It causes

trouble.

Caution

！

！！

！

･

This system only tells the outbreak of a fire. This system is not

Fire prevention systems. And Fire extinguishing system.

･

Do not use at the place where it exceeds environmental

specification. It causes trouble.

The Warning symbol is

used to indicate situations and conditions that

can cause operator serious injury and/or equipment damage.

The Caution symbol is

used to indicate situations and conditions that

can cause operator injury and/or equipment damage.

！

！！

！

Warning

Caution

！

！！

！

730110 K0

ES0911

Page

・ A term of a guarantee and a guarantee range

【A term of a guarantee】

In regard to the guarantee of this product, the designated payment of the order main thing

after the paying 1 years you guarantee first only the breakdown which occurs in the normal

busy condition which you follow the instruction manual.

【guarantee range】

In regard to the breakdown which it occurs in this product with the criticism of payment

person side during the above-mentioned guarantee period, it does returns repair in the

responsibility of payment person side. However, when it corresponds next, you exclude from

the object of this guarantee.

① Fire, earthquake and the damage by wind and flood, breakdown and the loss by the

thunderbolt and other natural disasters etc.

② After the shipping, transporting and moving and falling etc at your corporation,

breakdown and the loss with inadequate handling.

③ When cause of breakdown due to the reason other than the payment item.

④ Error in regard to use of the consumer, breakdown and the loss with repairing,

remodeling other than our company and error connecting.

⑤ In case of life of the relay part by wearing and depositing of the relay contact.

Furthermore, the guarantee referred to here being something which means the guarantee of

the payment item single unit, pardons the damage which is induced by the breakdown of the

payment item.

730110 K0

ES0911

Page

２

２２

２.

Installation

nstallationnstallation

nstallation

２．１．１． System configuration & Connection

This control unit receives the information of warning or breakdown from the detector which

is connected. In addition, it is the equipment which informs outside with the indication

LED and the warning buzzer and the signal contact.

① Control unit ： Control unit communicates with the detector,

Control unit controls the indicating LED and 7seg. LED and

the buzzer and signal contact according to the state of the

detector and itself.

FC1-DY：DIN rail mount type

FC1-HY：Surface mount type

② Communication line ： It is the line which shares the power supply and the

communication line of the detector.

③ Detector ： The connectable detector is shown with the 7th section.

２．１．２． Power Supply

Power supply of the control unit is DC24V±10%.

･

Please prepare for the control unit exclusive power supply as much

as possible.

･Please reduce the electrical noises on power supply.(Bellow 1Vp-p)

･If necessary, attach a proper noise filter to the power supply line.

Caution

！

！！

！

730110 K0

ES0911

Page

２.２. Installation of control unit

２．２．１． FC1-DY

FC1-DY is DIN rail mount type.

Loosen the screw of the metallic parts for the installation of 2 places which are on the

side of control unit itself. And put the control unit to the fixed 35mm width DIN rail.

Tighten the screw in the specified torque range. Please ensure that equipment installed

correctly.

(torque 1.00～1.35N･m： Reference value)

２．２．２． FC1-HY

FC1-HY is surface mount type.

Using the two screw holes of the metallic parts for the installation of 2 places which are

on the both side of control unit itself, please install securely in the equipment.

Tighten the screw in the specified torque range. Please ensure that equipment installed

correctly.

Please you have to match the screw installations environments.

･

Incorrect loading of the equipments can cause a malfunction,

failure or drop.

・Tighten the screw in the specified torque range.

・Under tightening can cause a drop, malfunction.

・

Over tightening can cause a drop, malfunction due to damage to

the screw or he equipments and malfunction.

！

！！

！

Warning

730110 K0

ES0911

Page

２．２．３． Installation places

The control unit must be installed on conductive place where is grounded. And must be used,

When it covers around control unit, electronic buzzer sound hears and becomes difficult to

take. In addition, also heat dissipation becomes bad, becomes cause of breakdown.

Because of this, usually at least please guarantee the space of width above 10mm substance

control unit top and around the guaranty of the passage of air current for heat dissipation

as a purpose.

２.３. Installation of detector

Install the mounting base for detector installation with the two screws M3 which is more

than 15mm length.

And install the detector just in the mounting base.

Caution

！

！！

！

Caution

！

！！

！

･

Install and use with environmental temperature and the humidity

which are within specification value.

･If the

control unit is not correctly installed, it causes the

malfunction, the breakdown, and the fall.

Please note it especially when using it with a lot of vibrations.

･

When the installation screw is loose, it causes the fall, the

short-circuit, and the malfunction.

･

When the installation screw is tightened too much, it causes the

fall, the short-

circuits, and malfunctions by the damage of the

screw and the control unit.

Install and use with environmental temperature and the humidity which

are within specification value.

730110 K0

ES0911

Page

２.４. Wiring

２．４．１． Power Supply

When turning on power source, rush current is between several mS, but above 10A it flows.

Wiring please tries to withstand this.

Earthing connection of the ground terminal please goes in order to protect the equipment

from electric shock accident prevention and electric noise, securely.

２．４．２． Communication line

The communication line is connected with control unit and detector as the power line and

the signal line. Therefore, use the shield cable of 0.5mm

, and connect the shield part in

the shield cable with the terminal FG.

Divergence wiring is possible concerning wiring. In addition also polarity is nonpolar

characteristics.

Do not bundle with line which gives out other electric noise and separate from it.

･Please do the wiring after the external power supply off. It may

get

an electric shock or the control unit may break down.

･Please use the terminal cover for the control unit when the unit

energized, after do the wiring.

If the terminal cover is not used, it may get an electric shock.

･When miss-

wiring or connecting to a power supply different from

ratings, it causes a fire and the breakdown.

･Please give the noise of power supply (DC24V±

10%) to the control

unit as 1Vp-p or less.

Please decrease with the power supply filter etc, whe

n the influence

of the noise is strong.

Caution

！

！！

！

！！

！

Warning

Caution

！

！！

！

[

Isolation from electric noise source such as power line

］

The signal conductor which is connected to the receiver and the receiver please wires

above 20cm separating from the power line.

Case it is not possible, please pass in the metallic conduit which the power line is

grounded.

730110 K0

ES0911

Page

３

３３

３.

Starting the system

Starting the systemStarting the system

Starting the system

３．１．１． Setting of control unit

Please verify whether the number of detectors which it is connected with the DET. NUMBERS

switch which is on the panel front is same.

When setting is different, trouble indication is lighting.

３．１．２． Power on

When the supply of power or power switch is pushed, the power light(green LED) lights up,

the system operates starts.

３．１．３． Register at time of power on

Power supply

OFF

Maximum 120 seconds

State of

Control unit

Initialize

※1

,Wait・Registration

※2

Supervision

※1 After power on, the alarm LED and the trouble LED blink sequentially.

※2 Control unit supplying power to the detector which is connected, starts communication.

Control unit inspects the address of all detectors which are connected, registers the detector

automatically.

When detectors of a quantity which is set in 120 seconds are registered, supervision is started.

When a quantity which is set with control unit and the number of detectors which are registered

are different it makes trouble.

Caution

！

！！

！

･

Pay attention to the sharp edge and the like when you handle control

unit. It becomes cause of the wound.

･

Do not operate switch with sharp and hard ones like a ball pen top.

It makes surface sheet make a tears.

･

Do not touch by hand where the oil is attached and the chemicals are

attached. The surface seat deteriorates and softens.

730110 K0

ES0911

Page

３.２. Control unit

３．２．１． Name and function of each section

① Operation panel

a． POWER ： Power supply switch (White)

Supply of power supply is started, or the each operation of POWER switch turns on/off the

system.

b． RESET ： Reset switch(Blue)

Operation of reset switch resets the alarm LED, alarm signal contact output and buzzer rumble

(continual sound).

However, when the detector still has alarm state, control unit for the second time becomes

alarm state.

The alarm LED and the trouble LED blink sequentially while resetting the alarm one by one.

Also, each segment LED of 7seg LED blinks in order one at a time.

c． DET. NUMBERS×10 ： Detector numbers switch(X10)

This is the switch whereby to set the connectable detector numbers by ten digits. (X10)

Caution

！

！！

！

Caution

！

！！

！

After turning off the system, until it turns on power supply again,

please provide the interval of a minute o

r more. There are times when

the system does not start normally.

Since the setting of this switch is re

cognized only at the time of

turning the power on, the power is to be off in the event of changing

the setting.

Tabla de contenidos

Otros manuales de Unidad de control de Fenwal Controls

Fenwal Controls

Fenwal Controls 05-50 Series Manual de usuario

Fenwal Controls

Fenwal Controls 35-9 Series Manual de usuario

Fenwal Controls

Fenwal Controls 35-71 Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario