GuilinFeiyuElectronicTechnologyCo., Ltd.http://www.feiyudz.cnEmail:service@feiyu-tech.com
GuilinFeiyuElectronicTechnologyCo., Ltd.http://www.feiyudz.cnEmail: service@feiyu-tech.com Page1
Hornet-OSD Manual
Dear customers:
Hello!ThankyouforpurchasingtheOSD of GuilinFeiyuElectronicTechnologyCo,
Ltd. Inordertoachievefull potential andsafeoperationof thisproduct,pleasecarefully
readthis manual priortoinstallation.
Preface
TheHornet-OSDoverlaysflighttelemetryinformationontoyourvideoimage.The
telemetryinformationdisplayedincludesflightaltitude, flight speed, flightdirection,and
homedirectionandsoon.Youalsocansavethe telemetryinformationtoaMICROSD
card(youshouldbuythecard byyourself, forwedon t offerit,pictureisshownasbelow ),
thenrealizingtrace playbackvia FYGCS.TheHornet-OSD canbeconnectedtothe
FY-21AP, FY-31APandFY-3ZT systemstodisplayautopilottelemetricdata,ortoaGPS
receivertodisplaypositioningdata.
Hornet-OSDautomaticallyadaptstoeitherPALorNTSCvideoinputandconfirms if
there is a MICROSD cardornot.Theadaptiveprocessesarewithinabout 20seconds.
Workingstatusexplanation:
Afterconnectingthepowersupply,theindicatorLEDlightwillbeactivated.The
Hornet-OSDwillautomaticallydetecttheincomingvideo(NTSCorPAL).The"NTSC"or
"PAL"will overlaidonthescreenwhenthevideosignalisdetected.IfData isreceived
fromtheautopilot(FY-21AP,FY31AP,FY-3ZT orGPS module)theLEDindicatorof
Hornet-OSDwill begintoflash.Ifnot,theHornet-OSD will automaticallyrestartafter
waitingfor20seconds.
Once theinputvideoisdetectedevenifthereisinterruptiontothevideosignal,the
telemetrydata of theHornet-OSD will continue tobetransmittedvia thevideostream.
InterfaceSchematic Diagram:
1.DANGER:The three “VCC”ports(positive) for VideoIn, Video Out and PowerIn areall
inter- connected.Thereforeyouareallowed toconnect ONEinputvoltageonly. DO NOT
input morethanone powersupplyor damagetotheOSDwill occur.
2.It isrecommended topowertheOSD independentlytoensureacleanvideodisplay.
3.NotethatpowertotheOSDisnot suppliedbytheAutopilotmodule.Powerisviathe12volt
input.
ListofInterfaces
PORT ConnectionDescription
Videoin Cameraor videoinputport
Videoout OSDOverlaidvideooutput,connect tovideotransmitteror videoscreen
SW RC receiverswitchinputtocontrolOSD display
Power OSDvideooverlayboardandcameraandvideotransmitterpowersupply.
Datain FY-21AP/FY-31AP/FY-3ZT/GPS datainterface
CurrentSensor
Current sensor input for measuringthebatteryvoltageandcurrent.
Detaileddescriptionof the “Videoin”port
GND Connect tothecameraGND
VCC
Connect tocamera spowersupply “VCC”.
(Note:Power issuppliedfromtheOSDtotheCamera.Donotinputanyother
power supplythroughthisport ordamage willoccur).
VideoIN Videoinput(Connect tothecameravideosignaloutput).
Detaileddescriptionof the “Videoout”port
GND Connect tovideotransmitterGND
VCC
Connect tovideotransmitterpowersupplyinput “VCC”.
(Note:Power issuppliedfromtheOSDtothevideotransmitter.Donotinput
anyother powersupplythroughthisport ordamagewilloccur).
VideoOut Videooutput (connect tovideotransmittervideoinput).
Detaileddescriptionof the “SW”port
GND Connect tothepower “GND”port oftheRCreceiver.
PWMIN
Connect tothesignalport ofyour RC receiver (youneedto
channel).
Detaileddescriptionof the “Power”port
GND Connected tothepower “GND”thatsupplytotheOSDcontrol board.
VCC
Connect tothepower “VCC”thatsupplytotheOSDcontrolboard(Safeinput
range: DC6Vto12V)
Note:thispowersupplyissent directlytoyourVideoCameraandVideo
Transmitter.E.g. ifyouareusinga12 volt VideoCameraandTransmitter,the
inputvoltageshouldalsobe12volt.
Detaileddescriptionof the “Data in”port
GND FY-21AP/FY-31APGND,orthe GNDoftheGPS
+3.3V UseonlytosupplypowertotheFY-GPS module.
(DO NOT connectthisporttotheFY-21AP/ FY-31APortheFY-3ZT).
DataTX Connect tothe “RX1”dataoutputportoftheFY-21AP/FY-31AP/FY-3ZT, or
the “RX”port oftheGPS module.
DataRX Connect tothe “TX1”dataoutputportoftheFY-21AP/FY-31AP/FY-3ZT, or
the “TX”port oftheGPS module.
Detaileddescriptionof the “CurrentSensor”port
ENGVCC Connect tobatterypositive (Red)
CUR AD Connect tothecurrentsensor outputsignal (White)
+5V +5Vpowersuppliedtothecurrentsensor fromOSD(Yellow)
ENGGND Connect tobatterynegative(Black)
CurrentSensor
Applicationdiagram
TheHornet-OSDcandirectlyconnect tothedataoutputportofFY-21AP, FY-31APor
FY-3ZT, orseparatelyconnect totheoutputport of GPS module,andthenoverlaytheflight
datainformationtothevideosignal.The applicationdiagramisshownasbellow.
Note Themodules intheimaginarylineframemeansthat youcan chooseanyone ofthese
modulestoconnect.
Introductionforthe flightStateofFY-21AP/FY-31APor FY-3ZT
NameIntroduction
RC ManualFlight. Autopilotdeactivated.
ABMAutobalance mode
FAF For FY-21AP:FixedAltitudeflyingmode;for FY-3ZT/FY-31AP:Airrouteflymode
RTL AutoReturnMode
ACMAutoCircleMode
Figure4. ConnectionSchematicDiagram
①
①
①
CurrentSensor
Datain
SW
Power
Videoout
Videoin
Feiyu Tech
MICRO SD card
Figure3.CurrentSensor
White
Yellow
BatteryPositiveInput
OutputtoECSNegative
BatteryNegative Input
OutputtoECSPositive
