FDI USB-ICP-SAB9 Manual de usuario

FDI

USB-ICP-SAB9

Quick Start Guide

FDI

Page 1 of 15 Rev 1.0

USB-ICP-SAB9 Quick Start Guide

The USB-ICP-SAB9 is a Socket Adapter Board designed to be used with the USB In-Circuit Programmer for

NXP Semiconductors LPC9xx devices. The SAB9 allows the user to program and test these microcontrollers

outside of the application circuit. Throughout this document we will just refer to the SAB9 rather than using the

complete part number since it simplifies the flow of information.

THE USB-ICP-SAB9 WILL NOT WORK WITHOUT A USB-ICP PROGRAMMER!

MAKE SURE TO INSTALL THE USB-ICP BEFORE USING THE SAB9!

Notice above that not all parts come in all packages. For instance, in the LPC93x family none of the devices

come in a DIP package. Therefore, for simplicity this document is arranged by package type rather than by part

family.

FDI

USB-ICP-SAB9

Quick Start Guide

FDI

Page 2 of 15 Rev 1.0

USB-ICP-SAB9 socket layout:

Each socket on the board is clearly labeled for the type of part that is programmed in it. When this document

refers to the ‘top’ of the board, this is referring to the top of the board when it is in the orientation shown in the

picture above.

FDI

USB-ICP-SAB9

Quick Start Guide

FDI

Page 3 of 15 Rev 1.0

Connecting the USB-ICP-SAB9 to a USB-ICP

To use the SAB9, it must first be connected to a PC through a USB-ICP with a USB-ICP-LPC9xx cable to P1,

as shown above. Or, if you do not have the USB-ICP-LPC9xx, the SAB9 may be connected to the PC with

regular Ethernet Patch cable to P2, as shown below. The USB-ICP must then be connected to the USB port on

your PC. To learn more about using the USB-ICP, please visit www.teamfdi.com/usb-icp

FDI

USB-ICP-SAB9

Quick Start Guide

FDI

Page 4 of 15 Rev 1.0

Frequently Asked Questions

For frequently asked questions regarding the USB-ICP please visit: www.teamfdi.com/usb-icp

Error Messages when Using Flash Magic

Flash Magic is the PC GUI interface software used with the USB-ICP programmer. If you are receiving error

messages when you try to program parts, go to ISP -> Read Device Signature and check below.

1. If the device signature reads all FF’s verify the following:

a. The part is oriented in the socket correctly.

b. The USB-ICP is connected to the SAB9 board according to one of the two methods mentioned

on Page 3.

c. That you do have a part in the socket.

d. That there is only one part in the board (you cannot program in two different sockets at the same

time)

2. If Flash Magic tells you that it failed to autobaud:

a. Make sure that the correct device is selected in the device drop-down menu.

3. If you receive the error message ‘Unable to communicate. (in use) Ensure no other applications

are using the COM Port. Try raising or lowering the baud rate.”

a. Make sure that you have the correct port selected and that the baud rate you have selected is the

rate recommended for the USB-ICP

FDI

USB-ICP-SAB9

Quick Start Guide

FDI

Page 5 of 15 Rev 1.0

P89LPC90x Devices in DIP8 Package:

SKT1

When placing any DIP8 Part in the SAB9 for programming, there must be 5 pins empty above and below the

part being programmed. The pin one identifier (notch in chip) should be toward the top of the board.

FDI

USB-ICP-SAB9

Quick Start Guide

FDI

Page 6 of 15 Rev 1.0

P89LPC2x Devices in DIP20 Package:

SKT1

When placing any DIP20 Part in the SAB9 for programming, there must be 2 pins empty above and below the

part being programmed. The pin one identifier (notch in chip) should be toward the top of the board.

FDI

USB-ICP-SAB9

Quick Start Guide

FDI

Page 7 of 15 Rev 1.0

Using the TSSOP Socket (SKT2)

To place a part in the TSSOP socket for programming, first push down on both sides of the socket with two

fingers. Then, once the socket is ‘open’ drop the part into the socket and nudge it into place to match the

documents below. When you release the sides of the socket the part will be locked in and ready for

programming.

FDI

USB-ICP-SAB9

Quick Start Guide

FDI

Page 8 of 15 Rev 1.0

P89LPC91x Devices in TSSOP14 Package:

SKT2

When placing any TSSOP14 Part in the SAB9 for programming, there must be 3 empty pins above and 4 empty

pins below the part being programmed. The pin one identifier (circle in top left corner) should be toward the

top of the board.

FDI

USB-ICP-SAB9

Quick Start Guide

FDI

Page 9 of 15 Rev 1.0

P89LPC91x Devices in TSSOP16 Package:

SKT2

When placing any TSSOP16 Part in the SAB9 for programming, there must be 3 empty pins above and below

the part being programmed. The pin one identifier (circle in top left corner) should be toward the top of the

board.

FDI

USB-ICP-SAB9

Quick Start Guide

FDI

Page 10 of 15 Rev 1.0

P89LPC92x Devices in TSSOP20 Package:

SKT2

When placing any TSSOP20 Part in the SAB9 for programming, there must be 2 pins empty above and below

the part being programmed. The pin one identifier (circle in top left corner) should be toward the top of the

board.

Tabla de contenidos

Otros manuales de Hardware de computadora de FDI

FDI

FDI SYG-S7G2-70C-MDK Manual de usuario

FDI

FDI ELI121-CRW Manual de usuario

FDI

FDI EyG SYG-S7G2-SOM Manual de usuario

FDI

FDI ELI70-CR Manual de usuario

FDI

FDI uEZGUI-EXP-DK Manual de usuario

FDI

FDI EyG YG-S7G2-SOM Manual de usuario

FDI

FDI uEZGUI-EXP1 Manual de usuario

FDI

FDI uEZGUI-EXP1 Manual de usuario

FDI

FDI UEZGUI-4357-70WVN Manual de usuario

FDI

FDI UEZGUI-1788-56VI Manual de instrucciones

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario