FBI XL-20 Manual de usuario

XL-20

Security System

Owner’s Manual

N9824 11/97

QUICK REFERENCE.................................................................................................................1

Turn System On ...................................................................................................................1

Turn System Off ...................................................................................................................1

Turn System On and Stay Inside..........................................................................................1

Turn System On: Perimeter Sensors

Instant Mode and Stay Inside...............................................................................................1

Smoke Detector Reset .........................................................................................................1

INTRODUCTION.........................................................................................................................2

SYSTEM REFERENCE..............................................................................................................3

XK-108 KEYPAD.........................................................................................................................5

TURNING THE SYSTEM ON .....................................................................................................8

Turn the System On and Leave............................................................................................8

Not Ready.............................................................................................................................8

To Turn the System On - Not Ready....................................................................................9

Turn System On and Stay Inside..........................................................................................9

Turn System On: Perimeter Sensors

Instant Mode and Stay Inside...............................................................................................9

Turn the System On with All

Sensors in Instant Response Mode......................................................................................9

Bypass..................................................................................................................................10

Turn the System Off .............................................................................................................10

USER CODES ............................................................................................................................12

Add or Change a User Code ................................................................................................12

Delete a User Code..............................................................................................................12

KEYPAD FUNCTIONS................................................................................................................13

Turn System On Only...........................................................................................................13

Keypad Send Help Conditions..............................................................................................13

Quick On...............................................................................................................................13

Quick Forced On ..................................................................................................................13

Quick Exit .............................................................................................................................14

Quick Bypass........................................................................................................................14

Set Time and Date................................................................................................................14

Turn Chime On/Off...............................................................................................................14

SYSTEM TEST...........................................................................................................................15

INSTALLATION LAYOUT...........................................................................................................16

SYSTEM LIMITATIONS..............................................................................................................18

GLOSSARY ................................................................................................................................20

FCC STATEMENT......................................................................................................................22

TELEPHONE OPERATIONAL PROBLEMS...............................................................................22

LIMITED WARRANTY ................................................................................................................25

TABLE OF CONTENTS

XL-20 Owner’s Manual

XL-20 Owner’s Manual - Page 1

Quick Reference

TURN SYSTEM ON

Check to make sure the system is READY - Green ready light is lit

Enter your four digit user code (or press the Arm button on your keyfob).

The On/Off (Arm) light will light .

Exit through a door designated by your installer as an exit/entry door.

TURN SYSTEM OFF

Enter through a door designated by your installer as an exit/entry door.

Enter your four digit user code (or press the Disarm button on your keyfob).

The System On (Arm) light will go out.

TURN SYSTEM ON AND STAY INSIDE

Check to make sure the system is READY - Green ready light is lit.

Followed by your user code

The On/Off (arm) light and the Stay light will both light.

REMEMBER: You must turn the system off if you want to open the door or

leave the premises after the exit time has passed.

TURN THE SYSTEM ON: PERIMETER SENSORS INSTANT

MODE AND STAY INSIDE

Check to make sure the system is READY - Green ready light is lit

followed by

followed by your user code

The On/Off light, the Instant light and the Stay light will all be on.

SMOKE DETECTOR RESET

Enter your four digit user code.

STAY

INSTANT

STAY

XL-20 Owner’s Manual - Page 2

Introduction

Congratulations on your decision to protect your home or business with the XL-

20 security system. You have chosen a reliable, state of the art security system

that is remarkably easy to operate. Your system has been professionally installed

by your local Security Company who can explain the specifics of your system.

The keypad is the input and display device for your security system. Your

system uses a XK-108 keypad. The XK-108 is a surface mount keypad

containing indicator lights for each of the 8 zones (areas of protection). The door

covering the buttons is optional and can be removed.

The XL-20 is listed by Underwriters Laboratories for Household Fire and

Burglary applications.

Throughout this manual the following conventions are used to display the

keystrokes required to perform the functions.

Button labeled BYPASS

Button labeled INSTANT

Button labeled STAY

Button labeled CODE

Four digit user code

Please keep your manual in a convenient location so you can refer to it if needed.

BYPASS

INSTANT

STAY

CODE

XL-20 Owner’s Manual - Page 3

SYSTEM REFERENCE

The following SEND HELP ALERTS are programmed into my system. Both

Buttons must be pressed at the same time to activate the alert. The buttons you

press depend on which type of keypad you have. Your installer will show you

how to activate these emergency keys.

ZONE

DESCRIPTION

Entry Time

Door

Exit Time

Entry Time is the same for all designated Entry/Exit Doors.

ZONE DESCRIPTION BUTTONS

Left

Center

Right

# & *

7 & 9

1 & 3

XL-20 Owner’s Manual - Page 4

USER ID

ASSIGNED TO

Account #

Telephone #

*Master User can add, change, or erase other user codes.

(MASTER USER 1)

Monitoring Station Information

XL-20 Owner’s Manual - Page 5

XK-108 KEYPAD

1) ZONE STATUS LEDS

These LEDS display the current zone status including alarms, bypasses, troubles

and faults. Each condition will cause these LEDS to operate differently as

follows:

ALARMS Fast Blink (approx. 150 ms. ON - 150 ms. OFF).

TROUBLES Slow Pulse (approx. 600 ms. ON - 600 ms. OFF).

BYPASSES Wink (100 ms. ON - 900 ms. OFF). Zone bypasses are displayed as

a very slow wink of the zone LED light.

FAULTED ZONES Solid ON. Faulted zones are the lowest priority indication.

Faulted burglary zones are displayed with the LED solidly ON while the system

is disarmed.

NORMAL OFF

2) ARM/DISARM LED

This LED indicates whether the system is currently armed (ON) or disarmed

(OFF). This LED will also blink fast to show that alarms have occurred or blink

slowly upon failure to communicate with the Central Station.

ARM

AC/LB

READY

XK-108 KEYPAD

STAY

INST

COVER

OPEN

Stay Instant

Bypass Code

*0#

789

456

123

PAF

TX LB

RF. SPVR

XL-20 Owner’s Manual - Page 6

3) STAY LED

This LED displays whether the system has been armed in the STAY mode or the

STAY/INSTANT mode. If the INSTANT LED is ON and the STAY LED is ON,

then the system is in the STAY/INSTANT mode. If the INSTANT LED is OFF

and the STAY LED is ON, then the system is in the STAY mode only. STAY/

INSTANT is enabled in programming question 05, location 2. In either mode the

STAY LED indicates the following:

ON Interior zones are bypassed

OFF Interior zones are active armedl

4) INSTANT LED

This LED displays whether the system has been armed in the STAY/INSTANT

mode, meaning that the system is currently armed, all delay zones are instant and

all interior zones are bypassed. NOTE: See programming question 05, location 2.

ON Delay zones are currently instant

OFF Delay zones are normal

5) AC/LOW BATTERY LED

This indicator light displays the current power status of the panel as follows;

ON AC is present

OFF No AC, running on battery backup

Slow Blink Low battery condition detected

6) READY LED

This LED displays whether the system is ready for arming. The READY light is

common to all BURGLARY ZONES with the following indications:

ON System ready to be armed

OFF System not ready to be armed

Slow Blink Indicates Installer programming mode

Fast Blink Alarm Memory Mode

7) STAY BUTTON

The STAY button enables arming the system, excluding zones programmed as

interior zones. This will provide exterior protection of the location while

XL-20 Owner’s Manual - Page 7

allowing full access throughout the interior.

8) BYPASS BUTTON

The BYPASS button is used to temporarily exclude protection of a specific zone.

9) INSTANT BUTTON

The INSTANT button enables arming the system elimenating entry/exit delays. If

enabled with the STAY button, it enables arming the system in the STAY/

INSTANT mode. NOTE: The INSTANT modes are enabled in question #05,

location 2.

10) CODE BUTTON

The CODE button is used to enter the installer programming mode and entry of

user codes.

11) KEYPAD AUXILIARY KEYS

Pressing the two keys (top & bottom) labeled "P" at the same time initiates a CS

transmission, if programmed, of PANIC, AUXILIARY or FIRE, annunciates the

keypad sounder and turns on the bell output. If not programmed to transmit, these

keys can only result in a local warning as follows (see question 05, location 1):

Keypad Sounder - Steady for PANIC, Pulsing for FIRE and AUXILIARY

Bell Output - Steady for PANIC, Pulsing for FIRE

12) TX LB LED

This LED will pulse whenever any RF transmitter has a low battery. Also, the

corresponding zone LED for that transmitter will pulse.

13) RF SPVR LED

This LED will indicate three different RF supervisory conditions and one bell

output supervisory condition as follows:

No supervision conditions exist (normal)

ON RF transmitter has not checked in for more than 12 hours

BLINKING (fast) RF transmitter reports a tamper condition

BLINKING (slow) Bell Output is in supervision

XL-20 Owner’s Manual - Page 8

TURNING THE SYSTEM ON

You can turn the Burglar portion of your security system on and off. Before you

turn the system on it must be ready. If you have a protected door open, or

someone is moving by a motion detector the system will not show ready.

The system is ready if the ready light is on.

TURN THE SYSTEM ON AND LEAVE

Enter your four digit user code.

The System On (Arm) light will go on.

Exit through a door designated by your installer as an exit/entry door. You must

leave within the period of time known as the exit time. Check the reference sheet

for the time that has been set for your system.

NOT READY

If the system is not ready to be armed, the READY light will be off and the Zone

lights will show which zone or zones are not ready. The zone lights on the

keypad indicate the following conditions:

Fast Blink Alarm

Slow Blink/Low Intensity Bypass

Slow Pulse Trouble

Solid On Not Ready

Example: If the Ready light is not lit and the zone one light is solid on. An alarm

sensor on zone one is not normal. This might mean that a window is open or

someone is walking through a motion sensor. Check all sensors on zone one and

resolve the problem. When all sensors are normal the Ready light will come on

and the zone light will go out.

TO TURN THE SYSTEM ON - NOT READY

Determine which zone or zones is not ready, resolve the problem and turn the

system on normally. If the problem cannot be resolved you may bypass the zone

that is not ready. Bypassing should only be done if the problem on the zone

cannot be resolved OR if you intentionally wish to leave the zone off. Example:

you wish to keep the window open for ventilation. Zones that are bypassed are

not protected when the system is on. See Bypass for the correct procedure.

Tabla de contenidos

Otros manuales de Sistema de seguridad de FBI

FBI

FBI Star XL 4800 EZ Manual de usuario

FBI

FBI XL-1T Instrucciones de montaje

FBI

FBI XL Star 4612 Manual de usuario

FBI

FBI XL-2 Manual de usuario

FBI

FBI XL-2T Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario