Fast 8295RT Manual de usuario
FAST TRACK TANK GEN 4B
INSTALLATION AND PARTS MANUAL
8295RT, 8320RT, 8345RT
8310RT, 8335RT, 8360RT
8320RT, 8345RT, 8370RT
Fast Global Solutions
4130 Commerce Boulevard
Windom, MN 56101
2
General Information
All rights, especially copying and distribution rights are reserved. No part of this publication may be reproduced in any
form or by any means, electronic or mechanical, including photocopying, without express written permission from Fast
Distributing, Inc.
Parts information in this manual represents components installed when product was manufactured based upon the best
available information. Modications made subsequent to initial delivery are not included. Always verify the parts and color
required with Fast Distributing, Inc at 1-800-772-9279.
If you have any questions, please contact your dealer or our Parts and Service Department.
3
Contents
General Information................................................................................................ 2
Remove Hydraulic Filter Cover, Step Assembly And Tool Box .......................... 4
Remove Center Link Bracket And Radar.............................................................. 5
Install Rear Tank Supports..................................................................................... 5
Install Receiver Mounting Brackets ...................................................................... 6
Install Setscrews..................................................................................................... 6
Install Radar ............................................................................................................ 7
Install Tanks ............................................................................................................ 8
Install Straps And Nylon Protector ..................................................................... 10
Install Windshield Washer Reservoir And DEF Fill Bracket ............................. 10
Install Step Assembly............................................................................................11
Tanks And Hardware ............................................................................................ 12
Plumbing................................................................................................................ 14
4
Remove Hydraulic Filter Cover, Step
Assembly And Tool Box
1. Remove hydraulic lter cover (1) and set aside. Cover
will not be re-installed with tanks installed on tractor.
2. Remove hardware from windshield reservoir (2),
mounting bracket and railing so reservoir can be moved
out of the way. Save all hardware to be reused.
3. Tractor with DEF Fill only, Remove hardware from DEF
ll bracket and save for reuse.
^WARNING
Step assembly weighs approximately 300 lbs.
Use an appropriate lifting device to prevent
injury.
4. Attach lifting device to step assembly.
5. Remove nuts, washers and carriage bolts (4), (5) and
(6). Save nuts, washers and carriage bolts (5) for reuse.
6. Remove step assembly.
7. Remove step bracket (7).
5
7. Remove tool box (8) from bracket. Tool box bracket does
not need to be removed.
Remove Center Link Bracket And
Radar
1. Remove center link (1) and mounting bracket from right-
hand side of tractor.
2. Disconnect radar harness from radar (2). Remove radar
from mounting bracket (3). Save hardware for reuse.
Remove radar mounting bracket (3).
3. Remove mounting bracket (3) from tractor. Mounting
bracket will not be reused.
Install Rear Tank Supports
1. Install right hand tank mount (1) with three M16 x 40mm
GR8.8 bolts and three M16 at washers. Repeat on left
side using left hand tank mount, three M16 x 40mm
GR8.8 bolts and three M16 at washers.
2. Install tank support (3) with two ½ X 1-½'' bolts (4),
½'' washers and ½'' nylock nuts. Do not fully tighten
as bracket will need to be adjusted when tanks are
installed later.
3. Install rubber isolator (5) with three ½ x 1-½' bolts (6)
and three ½'' centerlock nuts. Snug bolts to slightly
compress rubber. Repeat procedure for left hand side.
Note: For Ultra Wide Gauge tractor, brackets (1) and (3)
are reversed.
6
Install Receiver Mounting Brackets
^WARNING
Receiver mounting bracket weighs
approximately 105 lbs. Use an appropriate
lifting device to prevent injury.
1. Install left-side mounting bracket (1) to tractor with M20 x
60mm GR 10.9 bolts (2) and M20 at washers. Refer to
torque charts in this instruction for bolt torque values.
2. Install right-side mounting bracket (3) to tractor with M20
x 60mm GR 10.9 bolts (2) and M20 at washers. Refer to
torque charts in this instruction for bolt torque values.
3. Place rubber isolators (4) on top and bottom of bracket.
4. Place plate (5) on top of isolator and insert four ¾ x 9''
GR5 bolts (6) through plate and both isolators.
5. Repeat steps 3 and 4 for left-hand side receiver mounting
bracket.
^WARNING
Receiver mounting tube weighs approximately
105 lbs. Use an appropriate lifting device to
prevent injury.
6. Raise receiver mounting tube (7) into position with radar
bracket facing forward and install eight ¾'' centerlock
nuts. Tighten all eight bolts equally so some bulge is seen
on the rubber isolators.
Install Setscrews
1. Install four setscrews (1) in receiver tube. Verify setscrews
do not extend inside tubes.
7
2. Install two setscrews (1) in each receiver on left and right-
hand tanks. Verify setscrews do not extend inside tubes.
Install Radar
1. Attach radar (1) to mounting bracket (2) with existing
hardware.
8
Install Tanks
^WARNING
Each tank weighs approximately 1100 lbs.
Use an appropriate lifting device to prevent
injury.
1. Connect an appropriate lifting device to left-hand tank.
Tank will balance when strap is 77” from center.
2. Connect an appropriate lifting device to right-hand tank.
Tank will balance when strap is 77” from center.
Typical Lifting Device
3. Raise tank and guide into position on rear support
bracket (1).
4. Align tank receiver with front receiver and insert tube (2)
through tank and into front receiver.
9
5. Verify that tube (2) does not extend past front receiver
on right-hand side of tractor.
6. Install right-hand side tank using steps 1 and 2.
7. With right-hand tank (3) aligned with front receiver,
push tube (2) through right-hand tank.
8. Push both tanks inward against front receiver and
tighten eight setscrews (4) on front receiver and outside
of both tanks. Refer to torque charts in this instruction
for bolt torque values.
9. Disconnect lifting devices.
10
Install Windshield Washer Reservoir
And DEF Fill Bracket
1. Install windshield washer reservoir with supplied
hardware, remount windshied washer reservoir bracket
and mount reservoir with hardware removed earlier.
2. Bolt DEF Support bracket in place using two 592
carriage bolt 3/8 x 1 and two 769 3/8” nylock nuts.
Reinstall DEF Fill with hardware removed earlier.
Install Straps And Nylon Protector
1. Position strap (1) into place and insert nylon web (2)
between strap and tank. Insert studs on straps through
holes in tank supports. Place two ½'' washers and two
nylock nuts on studs and tighten only enough to keep
nylon web in place and tank from moving side to side.
Now tighten the bolts (see Page 5, step 2) that hold the
tank support to the tank mounts. Repeat procedure on
left side.
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
