Fanvil i10S Manual de usuario
1. Package Contents Mini Intercom
Quick Installation
Guide
Screw and tool
Connector
Mounting
Template
2. Physical specification
Device size 88 x 88 x 32 mm
i10S No camera, 1 button
With camera, 1 button
No camera, 2 button
i10SV
i10SD
1) Panel
Camera
Speaker
DSS key Call/Answer Unlock
Mountingdimensions Unit:MM
www.fanvil.com
i10S/i10SV/i10SD SIP Mini IntercomQuick Installation Guidei10S i10SV i10SD
2) Interface description
Open the rear case of the device, there is a row of terminal blocks for connecting
the power supply, indoor switch. The connection is as follows:
Serial
number Description
Ethernet interface: standard
RJ45 interface, 10/100M adaptive,
it is recommended to use five or
five types of network cable
Power interface: 12V/1A input
A set of short-circuit output
interfaces
A set of short-circuit input
interfaces
①②③④3. Installation Diagram
Cover Main body Back Cover Main body Back
a. Installation of rubber plug:
a) Wall mount: Attach the installation dimension drawing to the position to be installed,
use the electric drill to punch the hole in the 2 screw holes marked, and use the hammer
to drive the rubber plug into the drilled hole.
b) Built-in: Attach the installation dimension drawing to the position to be installed, open a
groove of the same size according to the size, use the electric drill to punch the hole in the
2 screw holes marked, and use the hammer to drive the rubber plug into the drilled hole.
Double VersionSingle Version
①
② ④③
Fanvil Technology Co., Ltd
Website: www.fanvil.com
Tel: +86-755-2640-2199 Fax: +86-755-2640-2618
Add: 10/F Block A, Dualshine Global Science Innovation Center,
Honglang North 2nd Road, Bao'an District, Shenzhen, China
b) Remove the cover;
c) Use a screwdriver to remove the 4 screws on the main body to separate the main body
from the rear case;
d) Pass all the wires through the hole in the lower right corner of the bottom case. All lines
must be reserved for a length of 15~20CM;
e) Fix the housing
a) Wall Mount: Align the bottom case with the position of the screw hole that was
previously punched on the wall, and screw in the two screws with a screwdriver to fix the
bottom case to the wall;
b) Built-in: Place the bottom case into the previously opened groove and screw in the two
screws with a screwdriver to secure the bottom case to the wall;
f) Connect power, network and control cables, and the test whether there is electricity by
doing the following:
a) Long press DSS key for 3 seconds(after power-on for 30 seconds), and when the
speaker beeps rapidly, press DSS key again quickly, the beeps stop ,the intercom will
report the IP address by itself.
b) If the work is normal, continue with the next steps.
g) Lock the 4 screws removed in step 3;
h) Cover the cover removed in step 2;
4. Searching device
Methods 1:
Download address: http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe
Open the iDoorPhone Network Scanner. Press the Refresh button to search the device
and find the IP address.
Method 2:
Long press DSS key for 3 seconds(after power-on for 30 seconds), and when the speaker
beeps rapidly, press DSS key again quickly, the beeps stop ,the intercom will report the IP
address by itself.
Method 3:
In addition, device provides the device surface DSS key operation to switch IP address
acquisition mode:
In the standby mode, long-press the DSS key for 3 seconds and the beep will last for 5
seconds. Within 5 seconds, press the DSS key three times quickly to switch to the
network mode.
a. If it is in the mode of DHCP and doesn't receive the IP address, switch it to the mode of
static IP (192.168.1.128), broadcast the IP address after the successful switch.
b. If it is in the mode of static IP address (192.168.1.128), switch it to the DHCP mode,
broadcast the IP address after the successful switch.
c. If it is in the mode of DHCP and obtain the IP address, the mode will not be switched
and directly broadcast the IP.
5. Fast settings
Step 1: Log in to the device page
Use the web browser input IP (for example: http://192.168.1.128) access.
The default user and password are admin.
Default DHCP
Client Enabled by default
Hold the DSS key for 3
seconds, then press the
DSS key again.
Default DHCP
Client
Static IP
address
Default
Web port
192.168.1.128
80
Default Setting
Step 2: Set SIP account
Set SIP server address, port, user name, password and SIP user with assigned SIP
account parameters. Select “Activate”, and then click [Apply] to save this setting.
Step 3: Set the volume (if not connected can skip)
Intercom settings => Media Settings => Media Settings
Set the device volume size, as shown below, click [Apply].
Speakerphone volume setting: set the speaker volume of normal calls.
Handsfree Mic Gain: set the microphone volume of call.
Step 4: Set function key (if not connected can skip)
Set the function key as shown below for a quick start, click [Apply] to save this settings.
Type: Memory key
Number 1 (Value): the function key will dial to this number 1
Number 2 (Value 2): if number 1 is unavailable, it will be forwarded to number 2.
Subtype: speed dial
Line: working line
Step 5: Set the security function
1 set of short-circuit input and output settings, tamper alarm server settings.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Sistema de intercomunicación de Fanvil
Fanvil
Fanvil i10 Manual de usuario
Fanvil
Fanvil i12 Manual de usuario
Fanvil
Fanvil i33V Manual de usuario
Fanvil
Fanvil i12 Manual de usuario
Fanvil
Fanvil i55A Manual de usuario
Fanvil
Fanvil i16V Manual de usuario
Fanvil
Fanvil i30 Manual de usuario
Fanvil
Fanvil i32V Manual de usuario
Fanvil
Fanvil i66 Manual de usuario
Fanvil
Fanvil I20-T Manual de usuario
Fanvil
Fanvil i31S Manual de usuario
Fanvil
Fanvil i51W Manual de usuario
Fanvil
Fanvil i23 Manual de usuario
Fanvil
Fanvil i56A Manual de usuario
Fanvil
Fanvil Y50r-Y Manual de usuario
Fanvil
Fanvil i31S Manual de usuario
Fanvil
Fanvil i12-01 Manual de usuario
Fanvil
Fanvil i16S-02P Manual de usuario
Fanvil
Fanvil I20-T Manual de usuario
Fanvil
Fanvil i51W Manual de usuario
