F&F LE-05d Manual de usuario

- 1 -

LE-05d

Electric energy meter,

without neutral wire

The LE-05d is a static (electronic) calibrated electricity meter,

used as a sub-meter for indicating the consumed three-phase

AC active electricity in the Arona metering system.

A special electronic system under the influence of current flow

and applied voltage in each phase generates pulses in propor-

tion to the electricity consumed in this phase.

Phase energy consumption is indicated by flashing the corre-

sponding LED (A and C). The sum of the three phases of pulses

indicated by a flashing LED is converted to energy taken in the

entire three-phase system, and its value is determined by the

segment LCD display.

Numbers after the decimal point indicate decimals (.1 kWh =100

Wh).

Purpose

Functioning

F&F Filipowski L.P.

Konstantynowska 79/81, 95-200 Pabianice, POLAND

phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71

www.fif.com.pl; e-mail: biuro@fif.com.pl

Do not dispose of this device in the trash along with other waste! According to the

Law on Waste, electro coming from households free of charge and can give any amo-

unt to up to that end point of collec� on, as well as to store the occasion of the pur-

chase of new equipment (in accordance with the principle of old-for-new, regardless

of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the

environment and human health.

- 2 -

Active energy consumed AE+ [kWh]

The meter is equipped with pulse output. This allows you to con-

nect another pulse device (SO) that reads pulses generated by

the meter. No additional connected equipment is required for

proper operation of the meter.

Measured values

Pulse output

Front description

- 3 -

The meter has sealable input and output terminal covers to pre-

vent any attempts to bypass the meter.

The meter is marked with individual serial number allowing its

unambiguous identification. The marking is laser engraved and

cannot be removed).

Sealing

Meter number

- 4 -

1.Disconnect the power supply.

2.The indicator mounted on a rail in the distribution box.

3.Use a screwdriver to unscrew the screws and remove the front

counter terminal covers.

4.Connect the voltages of the phases to be monitored as indica-

ted to the terminals 1 (L1), 3 (L2), 5 (L3).

5.Connect the circuit to be measured or a single consumer to the

terminals 2 (L1), 4 (L2), 6 (L3).

6.Connect an additional pulse receiver (optionally) to the termi-

nals 9(+) and 8(–).

An additional pulse receiver is not required.

7.Fit the meter terminal covers.

Meter number cont.

Mounting

- 5 -

1 L1IN phase 5 L3IN phase

2 L1OUT phase 6 L3OUT phase

3 L2IN phase 8 pulse output (–)

4 L2OUT phase 9 pulse output (+)

Wiring diagram

- 6 -

installation 3-wire

rated voltage 3×400 V

minimum measured current 0.04 A

base current 10 A

maximum current 100 A

voltage measuring range 160÷265 V

measurement accuracy (IEC62052) 1st class

rated frequency 50 Hz

insulation protection class II

housing PC+ABS material

own power consumption <10 VA; <2 W

indication range 0÷99999.9 kWh

meter constant 800 imp/kWh

signalling current consumption A, C phases 2×red LED

read-out signalling red LED

pulse output

type open collector

maximum voltage 27 V DC

maximum current 27 mA

pulse time

working temperature -20÷55°C

terminal 25 mm² screw terminals

dimensions 7 modules (122 mm)

mounting on TH-35 rail

ingress protection IP20

Technical data

- 7 -

F&F products are covered by a 24-month warranty from the date

of purchase. The warranty is only valid with proof of purchase.

Contact your dealer or contact us directly.

F&F Filipowski L.P. declares that the device is in conformity with

the essential requirements of the Low Voltage Directive (LVD)

2014/35/EU and the Electromagnetic Compatibility (EMC)

Directive 2014/30/UE.

The CE Declaration of Conformity, along with the references to

the standards in relation to which conformity is declared, can be

found www.fif.com.pl on the product subpage.

Dimensions

Warranty

CE declaration

- 8 -

E230427

»Please read the instructions carefully before installation.

»The device should be installed and operated by qualified per-

sonnel who are familiar with its design, operation, and asso-

ciated risks.

»Do not install a meter that is damaged or incomplete.

»The user is responsible for proper grounding of the system,

proper selection, installation, and efficiency of other devices

connected to the meter, including safety devices such as over-

current, residual current and overvoltage circuit breakers.

»Before connecting the power supply, make sure that all cables

are connected correctly.

»It is essential to observe the operating conditions of the meter

(supply voltage, humidity, temperature).

»To avoid electric shock or damage to the meter, turn off the

power supply whenever the connection is changed.

»Do not make any changes to the unit yourself. Doing so can

result in damage to or improper operation of the device,

which in turn can pose a threat to people operating it. In such

cases, the manufacturer is not responsible for the resulting

events and may refuse the provided warranty in the event of

a complaint.

General work safety conditions

Tabla de contenidos

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario