EXXOTEST CL550 Manual de usuario
www.exxotest.com
WARRANTY: 2 years parts and labour
48h-repair on return to factory, shipping paid
by sender
Document N° 00297502-v1
ANNECY ELECTRONIQUE S.A.S.
Parc Altaïs, 1 rue Callisto
74650 CHAVANOD
Tel: +33 (0)4 50 02 34 34
Fax: +33 (0)4 50 68 58 93
MULTIFUNCTION DIGITAL CONTROLLER CL550
For automobile diagnostics Oscilloscope, Voltmeter, EOBD reader
USER’S GUIDE
(Original copy)
(Key on last page)
2
8
3 4
11
12
13
14
10
5
6
1
9
7
2
WARNINGS AND PRECAUTIONS FOR USE
READ CAREFULLY BEFORE USING THE CL550
To ensure that the CL550 is used safely and to prevent damage to
the device:
Use the CL550 in full respect of the instructions given in this
manual, to avoid damaging its built-in protection.
Do not use the CL550 if the device or its measuring cords are
damaged, or if the device does not seem to be working correctly.
Check that the CL550 is operating correctly by measuring a
known voltage. If there is any doubt - have the equipment
checked.
Never apply a voltage higher than 50V to the measurement
terminals.
Do not use the device in the vicinity of explosive gases, steam or
dust.
Respect all safety instructions concerning the equipment being
tested.
!
3
CONTENTS
1. GENERAL PRESENTATION .................................................................. 4
CONNECTING THE DEVICE ............................................................................................. 4
CONTENTS OF CL550 CASE ........................................................................................... 4
AVAILABLE OPTIONS ....................................................................................................... 5
2. MAIN SCREEN ....................................................................................... 6
CONTROL BUTTONS........................................................................................................ 7
3. DIAGNOSTIC FUNCTION ...................................................................... 7
4. DC VOLTMETER FUNCTION ............................................................... 10
5. DC AMMETER FUNCTION ................................................................... 11
6. OSCILLOSCOPE FUNCTION............................................................... 12
CONFIGURING SETTINGS ............................................................................................. 12
SELECTING MEASUREMENTS, PAUSE FUNCTION, EXAMPLES ............................... 14
......................................................................................................................................... 14
7. SETTINGS MENU ................................................................................. 15
8. USE WITH A COMPUTER .................................................................... 16
INSTALLING THE DRIVER .............................................................................................. 16
INSTALLING THE USB CAPTURE SOFTWARE ............................................................ 17
INSTALLING THE USB UPDATE SOFTWARE ............................................................... 19
9. TECHNICAL SPECIFICATIONS ........................................................... 20
10. CE DECLARATION OF CONFORMITY ................................................ 23
DESCRIPTION ................................................................................................................. 24
4
1. GENERAL PRESENTATION
CONNECTING THE DEVICE
The EXXOTEST® CL550 digital controller can be used
in different ways:
- EOBD reader:
In this case, connect the CL550 to the diagnostic port of
the vehicle inspected. This mode uses the device's
EOBD connection (item A).
- Voltmeter, Oscilloscope:
- Power supply:
If the EOBD reader is not used, the CL550
can be powered directly by the vehicle
battery, using the adapter provided (item C).
- Dialogue with PC:
A
The voltage readings require the use of one or
both of the measuring wires provided (item
B
).
C
B
D
The USB cable (item D) enabling dialogue with a
computer and the USBCapture software are also
provided in the case with the CL550 device.
5
Measuring wires with touch
points (1 red, 1 black)
CL550 device with EOBD built-in
lead (vehicle diagnostic port)
EOBD cable / clamps for
direct power supply from
vehicle battery
USB cable: connection of CL550 to
computer (for printing, updates, etc.).
Instructions and CD-Rom (contains
the user manual and software)
CONTENTS OF CL550 CASE
AVAILABLE OPTIONS
Optional cord (AMUX-COBD3-L): used
to power the CL550 from the 4 mm
terminals featured on training mock-ups
or stabilised power supply.
Ammeter clamp
(ref.: PA25)
Once connected to the vehicle (diagnostic port or battery), or to the
computer (USB port), the CL550 emits an audible signal and displays the
home screen:
The device is ready for use
6
Rotate the selector button to move the
cursor.
2. MAIN SCREEN
Press the selector button to access the
mode selected.
Confirm:
Select:
The menu selected is highlighted in blue:
in the example above: Diagnostic is selected.
When the CL550 device is powered up,
it emits an audible signal and the home
screen is displayed. The first line
Diagnostic is selected by default (see
illustration).
Use the centre button (item 10) to
browse the device menus.
10
7
CONTROL BUTTONS
3. DIAGNOSTIC FUNCTION
The diagnostic function is selected by default when the device is powered-up.
Press the centre button to enter this mode:
Selector button:
Rotate to change the selection
Press to confirm the selection
Settings:
Shortcut to Settings menus (general
or oscilloscope).
Inactive buttons
Back:
Closes a menu or quits the
current mode.
8
If the following screen is displayed, several situations are possible:
Either the EOBD port is not connected, or
The vehicle
(or equipment) connected does not use
the EOBD standard, or
The vehicle
ignition is off.
Once the device is connected, three choices are available:
- Read parameters:
The parameters returned by the vehicle are
displayed; the selected parameter is described
in the bottom part of the screen.
- Read fault codes without the presence of
faults:
If the engine management system queried is
operational, the message 'No fault code' is
displayed. Otherwise, the faults present are
listed (
see next page).
9
Read fault codes with presence of faults:
- Erase fault codes:
Select this line and confirm to erase fault
codes, confirmation is shown in the illustration.
Number of fault code
Description of fault code
Full description of the fault code selected
Fault code level: transient, awaiting confirmation or confirmed.
10
4. DC VOLTMETER FUNCTION
Use the red wire to measure a single voltage in relation to the battery Earth
(1 channel) or the red and black wires to measure two distinct voltages in
relation to the battery Earth (2 channels).
OR
Select the DC Voltmeter mode on the main screen (rotate the centre
button to reach it) and confirm (press the centre button) to be presented
with two possibilities: 1 channel or 2 channels
Tabla de contenidos
