Extron electronics TLI Pro 101 Manual de usuario

Product Category

IMPORTANT:

Go to for the

complete user guide and installation

instructions before connecting the

product to the power source.

TLI Pro 101 • Setup Guide

Overview

The Extron TLI Pro 101 is a TouchLink®Interface that works with any Extron IP Link®Pro control processor, to allow a third party

touchscreen display to be used as a point of control within an Extron Pro Series control system. The scaled output supports

displays from 800x600 to 1920x1200, as well as HDTV 1080p/60. This guide provides instructions for experienced installers to

mount and install a TLIPro 101 and to create a basic conguration. For more complete instructions, see the TLIPro 101 User

Guide, at www.extron.com.

Setup Checklist

Get Ready

Download and install the latest version of the following software:

Global Configurator Professional or Global Configurator Plus — for setting up and conguring the control processor and

touchpanel.

GUI Designer — for designing layouts for Extron TouchLink®Pro touchpanels and third party touch interfaces.

Both software programs are available from www.extron.com.

Obtain the following network information from your network administrator:

DHCP status (on or off). If DHCP is off, you will also require

IP address Subnet mask Gateway

User name — by default these are either admin or user.

Passwords — the factory congured passwords for all accounts on this device have been set to the device serial

number. Passwords are case sensitive.

NOTE: If the device is reset to default settings, the password is the default password conguration. The default

password is extron.

Make a note of the interface MAC address.

Mount and Cable All Devices

ATTENTION:

• Do not power on the TLI Pro 101 or control processors until you have read the Attention in the Power Supply section

of the TLI Pro 101 User Guide or the IPL Pro User Guide.

• Ne branchez pas le TLI Pro 101 ou les contrôleurs avant d’avoir lu la mise en garde dans la section «sources

d’alimentation» du TLI Pro 101 UserGuide ou du IPLProUserGuide.

Mount the units. Stand the TLI Pro 101 on a convenient surface, mount it in a standard rack, or use an under-table mounting

kit (see the TLIPro 101 User Guide, at www.extron.com). To mount the third-party touchpanel follow the instructions

provided by the manufacturer.

Connect cables to the TLI Pro 101.

Connect the HDMI output from the TLI Pro 101 to the third-party touchpanel.

Connect the USB port from the TLI Pro 101 to the third-party touchpanel.

NOTE: The USB connection passes information to the TLI Pro 101 about where on the screen the touchpanel was

pressed. To use a normal monitor, instead of a touchscreen, connect a mouse to the TLI Pro 101 USB connection.

Use the mouse to click on screen icons.

Connect power cords and power on all devices.

Set up the TLI Pro 101 for Network Communication

Connect the PC that you will use for setup, the control processor, and TLI Pro 101 on the same Ethernet subnetwork.

Use the Setup Menu (see page 3) or the Toolbelt feature of Global Congurator Professional or Global Congurator Plus to

set the DHCP status and, if necessary, the IP address, subnet mask, gateway, and related settings for the interface.

www.extron.com

TLI Pro 101 • Setup Guide (Continued)

Conﬁgure the Interface

The Global Conﬁgurator Professional Help File, the Global Conﬁgurator Plus Help File, and the GUI Designer Help File provide

step-by-step instructions and more detailed information. The Global Congurator Professional and Global Congurator Plus help

les include an introduction to the software and sections on how to start a project and conguration.

Rear Panel Connectors and Features

For complete information about the TLI Pro 101 rear panel connectors and features, see the TLI Pro 101 User Guide.

TLI PRO 101

LAN/PoE

USB

HDMIHDMI

POWER

12 V

RESET

CONTROLOUTPUT

1.0A MAX

INPUT

AB GFECD

Figure 1. TLI Pro 101 Rear Panel

ATTENTION:

• The TLI Pro 101 can use a 12 VDC desktop power supply and is also Power over Ethernet (PoE 802.3af, class3)

compliant. Do not connect either power supply before reading the Attention in the Power Supply section of the

TLIPro101 User Guide.

• Le TLI Pro 101 peut utiliser une source d’alimentation externe 12 Vcc, et est également compatible avec l’alimentation

POE via Ethernet (PoE 802.3af, classe 3). Ne branchez pas de sources d’alimentation externes avant d’avoir lu les

mises en garde dans la section «PowerSupply» du TLIPro101 User Guide.

APower connector — Connect the 2-pole, 3.5 mm captive screw connector from the provided 12 VDC, 1.0 A power supply to

this socket.

NOTE: The TLI Pro 101 also complies with Power over Ethernet standards (PoE 802.3af, class 3).

BHDMI input — Plug the cable from the input source device into this female HDMI type A connector. Use the provided LockIt

brackets to secure the connector to the TLI Pro 101 unit.

CHDMI output — Connect this female HDMI type A connector to a third-party touch screen. Use the provided LockIt brackets

to secure the connector to the TLI Pro 101 unit. A full list of compatible resolutions is provided in the TLI Pro 101 User Guide.

DUSB connector — supports High-speed USB 2.0 control. Plug a USB cable from the third-party touchpanel into this female

typeB connector.

NOTE: To use a monitor that is not a touchpanel, connect a mouse to this port.

ENetwork and Power over Ethernet connector — Connect the interface to the LAN using a twisted pair cable, terminated

with an RJ-45 connector. The connector can also be used with a PoE power injector (not provided).

An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.

FReset mode LED — indicates power status and reset status of the device.

GReset button (recessed) — allows the unit to be reset in any of three different modes. A brief summary of the reset modes is

given below. For more information see the TLI Pro 101 User Guide.

Product Category

Front Panel Features

TLI PRO 101

TOUCHLINK INTERFACE

ACT

LINK

100

ABED

Figure 2. TLI Pro 101 Front Panel

APower LED — Lights green when the unit is powered on.

BMenu button (recessed) — opens the setup menu and calibration screen for the interface:

zPress the button briey (less than 2 seconds) to open the internal menu screens.

zPress and hold the button (at least 2 seconds) to open the calibration screen. Follow the on-screen instructions to

calibrate the touchpanel.

zPress the button briey (less than 2 seconds) for a second time to close the current screen without saving any changes.

C100 Mb network LED — Lights green when the unit is connected to a 100 Mb network.

DNetwork link LED — Lights green when the unit is connected to any network.

ENetwork activity LED — Blinks amber when there is activity on the network connection.

Reset Modes: a Brief Summary

The TLI Pro 101 offers the following reset modes:

• Use factory firmware: Press and hold the Reset button (Figure 1, G) while applying power to the unit. Use this

mode to replace rmware in the event of rmware failure.

• Reset All IP Settings: Press and hold the Reset button for 6 seconds. After the Reset LED (Figure1,F) ashes

twice, release and momentarily press the Reset button. Use this mode to reset all network

settings without affecting user-loaded les.

• Reset to Factory Defaults: Press and hold the Reset button for 9 seconds. After the Reset LED ashes three times,

release and momentarily press the Reset button. Use this mode to return the interface to

factory default settings.

NOTES:

• The factory congured passwords for all accounts on this device have been set to

the device serial number. Passwords are case sensitive.

• If the device is reset to default settings, the password is the default password

conguration. The default password is extron.

Setup Menu

Press the menu button (see Front Panel Features, Babove) to

open the setup menu. Select any of the six available screens (Status,

Network, Output, Audio, Input, and Advanced) by pressing the

appropriate button in the navigation bar at the top of the screen.

Press the menu button for at least 2 seconds to open the calibration

screen. Follow the on-screen instructions.

Info

Model: TLI Pro 101

Part Number: 60-1083-01

Firmware

Version: 1.00

PoE Status:On

Network

IP Address:

DHCP:

Host Name:

Off

192.168.254.251

TLI-AB-CD-EF

Output

Resolution:

Project:

Sleep Timer:

800x600

N/A

5 Minutes

Audio

Master Volume:

Master Mute:Off

Input

HDMI Port:No Signal

Status Output AudioAdvanced Exit

NetworkInput

Advanced

Controller IP:N/A

Project Size:N/A

Figure 3. Setup Menu

All trademarks mentioned are the property of their respective owners.

68-1817-50 Rev. C

01 20

TLI Pro 101 • Setup Guide (Continued)

Otros manuales para TLI Pro 101

Tabla de contenidos

Otros manuales de Equipo de grabación de Extron electronics

Extron electronics

Extron electronics RGB 304 Manual de usuario

Extron electronics

Extron electronics SSP 200 Manual de usuario

Extron electronics

Extron electronics TLI Pro 201 Manual de usuario

Extron electronics

Extron electronics RGB 203 Rxi VTG Manual de usuario

Extron electronics

Extron electronics Converter CVC 200 Manual de usuario

Extron electronics

Extron electronics TLI Pro 101 Manual de usuario

Extron electronics

Extron electronics RGB 109xi Manual de usuario

Extron electronics

Extron electronics RGB 109xi Manual de usuario

Extron electronics

Extron electronics VNR 100 Manual de usuario

Extron electronics

Extron electronics SSP 7.1 Manual de usuario

Extron electronics

Extron electronics RGB 124 Manual de usuario

Extron electronics

Extron electronics ACP 106 EU Manual de usuario

Extron electronics

Extron electronics Wall and Floor Box Mountable Interfaces RGB... Manual de usuario

Extron electronics

Extron electronics RGB 400 Series Manual de usuario

Extron electronics

Extron electronics AXI 22 AT D Manual de usuario

Extron electronics

Extron electronics KNX 100G Manual de usuario

Extron electronics

Extron electronics RGB 580x Manual de usuario

Extron electronics

Extron electronics RGB 158xi Manual de usuario

Extron electronics

Extron electronics IP Link IPL T CR48 Manual de usuario

Extron electronics

Extron electronics RGB 500 AKM Manual de usuario

Extron electronics

Extron electronics RGB 190F Manual de usuario

Extron electronics

Extron electronics MLA-VC10 Manual de usuario

Extron electronics

Extron electronics RGB 202 VS SL2 Manual de usuario

Extron electronics

Extron electronics RGB 190FV Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado