Extron electronics TLP Pro 320C Manual de usuario

Product Category

IMPORTANT:

Go to www.extron.com for the

complete user guide and installation

instructions befor

e connecting the

oduct to the power sou

rce.

TLP Pro 320C • Setup Guide

Overview

The Extron TLP Pro 320C is a 3.5 inch Cable Cubby®touchpanel with a ip-up, 320x240 LCD touchscreen with 18-bit color

depth. It is ideal for any AV application requiring a compact, Cable Cubby touchpanel with a customizable interface. This guide

provides instructions for experienced installers to mount and install a TLPPro 320C touchpanel. For more complete instructions,

see the TLPPro 320C User Guide, at www.extron.com.

Setup Checklist

Get Ready

Download and install the latest version of the following software (available from www.extron.com):

Global Configurator Plus and Professional — for setting up and conguring the control processor and touchpanel.

GUI Designer — for designing layouts for Extron TouchLink®Pro touchpanels and third party touch interfaces.

Obtain the following network information from your network administrator:

DHCP status (on or off). If DHCP is off, you will also require the following:

IP address Subnet mask Gateway

User name — by default these are either admin or user.

Passwords — by default these are either extron (for admin) or the eld is left blank (for user).

Make a note of the touchpanel MAC address.

Make sure you are familiar with all the included parts and have all the necessary tools (see Tools Required for Installation

on page 2) for installing the CableCubby.

Included Parts

US Power

Module

Universal

PowerModule

Without Power

Module

AC Power Module 11 1 0

Pass-through AAPs 2,3 4 3 4

Blank AAPs 3 3 5

1-position bracket kit 40 1 0

2-position bracket kit 2 1 3

3-position bracket kit 1 1 1

NOTES:

1 Inside the US, the TLP Pro 320C can be purchased with or without an ACpower module. Outside the US, see

www.extron.com to nd a power module that is suitable for your location.

2 Each AAP Bracket Kit consists of two brackets. The rear bracket is higher than the front bracket and has two holes for

screws.

3 Active or Passive AAPs are not provided. Purchase them separately (see www.extron.com).

4 Single-space brackets can only be installed in one location (see the note and ﬁgure on page 4).

TLP Pro 320C

Table Clamps

AC Power Module*

Blank AAPs

Pass-thru AAPs

Extron

Removal Tool

Zip Ties #4−40 Screws

and Nuts

2 Pos

AAP Shelf Bracket Kits

(2 brackets/kit)

3 Pos1 Pos

TLP Pro 320C • Setup Guide (Continued)

Tools Required for Installation

Safety Glasses

Phillips Screw Driver

Tape Measure

1/4" Hex Nut Driver

Marking Pen

Square

Vacuum Cleaner

Mount and Cable All Devices

ATTENTION:

• Do not power on the touchpanels or control processors until you have read the Attention in the Power Supply section

of the TLP Pro 320C User Guide or the IPL Pro User Guide.

• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «sources

d’alimentation» du TLP Pro 320C UserGuide ou du IPLProUserGuide.

Mount the units (see Mounting).

Install power modules in the cable cubby.

Install AAPs and run cables to the cable cubby.

Connect power and network cables to the touchpanels.

NOTE: The TLP Pro 320C can use either a 12 VDC power supply or a PoE power injector.

Connect the power cords and power on all devices.

Set up the Touchpanels for Network Communication

Connect the PC that you will use for setup, the control processor, and the touchpanel to the same Ethernet subnetwork.

Use the Setup Menu (see Setup Menu on page 8) or the Toolbelt feature of Global Congurator Plus and Professional to set

the DHCP status and, if necessary, the IP address, subnet mask, gateway, and related settings for the touchpanel.

Conﬁgure the Touchpanels

The Global Conﬁgurator Help File, and the GUI Designer Help File provide step-by-step instructions and more detailed

information. The Global Conﬁgurator Help File includes an introduction to the software and sections on how to start a project and

congure it.

Mounting

Planning

Before making any cuts, select the best location for the TLPPro 320C.

Ensure that the edge that opens on the lid is oriented correctly.

Ensure there is enough space for all the system cables and components, including cable retractors, if they are required. The

space requirements for retractors are shown in the TLP Pro 320C User Guide, which is available at www.extron.com.

Decide on the method for cutting a hole in the table:

Hand router and template

CNC wood router

Jigsaw and paper template

Verify that you have the correct template or dimensions.

Check all relevant regulations.

Ensure that the installation complies with local, state, and national building and electrical codes.

Ensure that the installation complies with the Americans with Disabilities Act or other accessibility requirements.

Product Category

Step 1 — Obtain Cut-Out Dimensions

ATTENTION:

• The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople. Exercise care

to prevent scarring or damaging the furniture.

• L’ouverture dans la table pour le CableCubby devrait être coupée seulement par des artisans autorisés et qualiés.

Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.

• Use the appropriate metal Extron routing template or refer to the surface cutout dimensions before cutting a hole in

the furniture or other surface. Pay special attention to the direction the unit will face. The connector access side is

underlined (see Using a CNC wood cutter). Extron is not responsible for miscut mounting holes.

• Utilisez le gabarit de détourage métallique approprié ou reportez-vous aux dimensions de découpe de la surface

indiquées ci-après avant de découper le meuble ou la surface. Faites particulièrement attention à la directions dans

laquelle l’unité sera dirigée. Le côté pour accéder au connecteurs est souligné (voir Using a CNC wood cutter).

Extron ne sera pas responsable des erreurs de coupe.

• Ensure the table surface is at least 0.375 inch (0.95 cm) thick.

• Assurez vous que la surface de la table est au moins 0,95 cm (0,375 pouce) d’épaisseur.

If using a hand router, you should purchase the Extron TLP Pro 320C routing template.

If using a CNC wood router, use the exact cut-out dimensions (see Using a CNC wood cutter).

If using a reciprocating saw or jigsaw, use the paper cut-out template (available under the Downloads tab on the TLP Pro 320C

page at www.extron.com).

Step 2 — Cut the Surface

CAUTION: Risk of personal injury: Wear safety glasses when operating power equipment.

ATTENTION: Risque de blessure: Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique.

Ensure the cut is laid out in exactly the desired location and the edge that opens on the lid is correctly oriented. After verifying and

checking dimensions, cut a hole in the surface of the furniture where the enclosure will be installed (see “Preparing the Table” in

the TLP Pro 320C User Guide). There are three methods for cutting the hole in the table:

Using a hand router

Recommended method — Use the Extron TLP Pro 320C

routing template. Refer to the Routing Template User Guide,

available at www.extron.com, to prepare the template and

use the template to cut the hole.

NOTE: Purchase the metal router guide separately. Do

not discard it when the installation is complete as it is

reusable.

Using a CNC wood cutter

Recommended method — Use the exact cut-out dimensions:

7.50 +0.00/-0.02 inches W x 6.00 +0.00/-0.02 inches D

19.05 +0.00/-0.05 cm W x 15.24 +0.00/-0.05 cm D

NOTE: The underlined dimension is the connector or AAP

access side for the unit.

Using a reciprocating saw or jigsaw

Acceptable method — Use the paper cut-out template (available

under the Downloads tab on the TLPPro 320C page at

www.extron.com).

HSA 200

USER ACCESS

HSA 200

CABLE CUBBY 300

USER ACCESS

Cut-Out Template for the Extron

TLP Pro 720C

Outer Edge of Trim Ring

(Do not cut this line.)

1. Confirm the product to be installed.

2. Remove the surface cut-out area

(gray)from thetemplate.

3. Mark the position on the wall or

furniture where theTLP 710MV

is being installed.

4. Cut the opening.

P/N 68-2046-01 Rev. B

Page size: 11" x 17"

Print scale 1:1

Do not shrink.

P/N

TLP Pro 320C • Setup Guide (Continued)

Step 3 — Run all Cables

Run all cables necessary to support the AC connector, the cables stored in the cubby, and all planned AAP connectors. Run the

cables below the table and through the hole that was cut in Step 2 (see page 3). Leave enough slack in the cables to connect

or route them before the cubby is installed in the table. Leave enough space under the TLPPro 320C enclosure for the external

power supply and connection of AV cables and the network connection.

Step 4 — Install Cable Retractors (Optional)

If required, Extron cable retractors should be installed in the enclosure at this stage. For complete information about retractors

and how to install them, see the TLP Pro 320C User Guide and Retractors User Guide at www.extron.com.

Step 5 — Install Power Module (Optional)

ATTENTION:

• For units that are used in North America, only

use AC power modules that are UL Listed Model

“Cable Cubby AC Power Module”.

• Pour les unités qui sont utilisées en Amérique

du Nord, utilisez seulement les modules

d’alimentation secteur qui sont listés UL, modèle

« Cable Cubby AC Power Module ».

• The unit is not UL Listed if it uses any AC power

module other than Model “Cable Cubby AC Power

Module”.

• L’unité n’est pas listée UL si elle utilise tout autre

module d’alimentation secteur autre que le modèle

« Cable Cubby AC Power Module ».

NOTE: For models that do not include a power module, see the Extron website to select a power module that is suitable for

your location.

The power module takes up two or three AAP spaces, depending on the model. Install it before or after the AAP assembly is

installed. It may be installed with AAPs on either side.

1. Secure the power module into position with #4-40 Phillips head screws and star washers.

CAUTION: Risk of electric shock: To ensure proper electrical grounding, use the provided grounding screws and star

washers.

ATTENTION : Risque de choc électrique: An d’assurer une mise à la terre correcte, utilisez les xations de mise à la

terre et les rondelles en étoile fournies.

2. Run the cable or conduit to a convenient junction box.

Extron recommends the circuit be attached to a junction

box that is directly wired to the main circuit.

Step 6 — AAP Assembly

Install all desired cables into the cable pass-through AAPs and

install the AAPs into the cable cubby.

The simplest way to install the cables and AAPs is to populate

the AAP brackets outside the cubby and then install the

populated AAP shelf assembly into the cubby.

Install cables in the pass-through holes as shown in the gure

to the right.

TIP: Hand tightening the #4-40 nuts makes it easier to

place and secure the assembly inside the enclosure.

NOTE: An extra column of AAP bracket mounting points is

available for use with TLP Single-space AAP mounting

brackets. Single-space brackets will not t in any other

location.

Rear Bracke

Front Brackets

Secure the po

wer module

to the

TLP Pro 320C frame

with #4-40 Phillips head

scre

ws and star washers.

The extra column

of mounting points

is for installing

single-space

AAP brackets.

Product Category

Step 7 — Install the AAP Assembly

1. From under the table, push the rst AAP assembly

through the bottom of the enclosure. The holes in the rear

bracket must align with the bottom row of holes on the

rear face of the enclosure.

TIP: Ensure there is enough space above the AAP

assembly for the lid to close completely without

cables or connectors contacting the touchpanel.

2. Secure the AAP assembly into position with the provided

Phillips head screws.

3. Tighten the nuts that secure the AAPs to the brackets.

Step 8 — Mount the Enclosure

Mount the cable cubby enclosure in the table.

CAUTION: The anged edges of the top of the surface enclosure are sharp. These edges are also soft and may be easily

nicked or bent. Exercise caution when handling the enclosure to prevent personal injury or damage to the enclosure.

ATTENTION : Les extrémités à brides du haut de la surface du boîtier sont aiguisées. Ces extrémités sont aussi lisses

et peuvent facilement être coupées ou pliées. Soyez prudents lorsque vous manipulez le boîtier an d’éviter de

l’endommager ou de vous blesser.

1. Remove the edge grommet protecting the edges of the trim ring

and the plastic lm on the nished surfaces.

ATTENTION:

• Do not use isopropyl alcohol or other solvents to

clean the Cable Cubby. Strong solvents will ruin some

nishes.

• Ne pas utiliser de l’alcool isoproprylique ou d’autres

solvants pour nettoyer le CableCubby. Les solvants

forts endommageront certaines nitions.

2. Carefully lower the enclosure into the hole cut in the table (see

Step2 — Cut the Surface on page 3). Ensure the trimring(5) is

ush with the top of the table.

3. Under the table, attach the table clamps (3) to the pins on

each side of the enclosure. It may be necessary to loosen the

wingnuts (1) and the Phillips head screws (2).

4. When the clamps are properly seated on the pins, tighten the

Phillips head screws until the clamp faces (4) are tightly secured

against the bottom of the table.

5. To prevent the screws from becoming loose, secure the wingnuts

against the table clamp bodies.

COMPUTER

AUDIO

Phillips Head Scre

(secure AAP

assemb

ly)

Tighten down

AAP nuts.

Push assemb

ly through

bottom of enclosure.

Large holes

provide tool

access to fasten

rear brackets.

TLP Pro 320C • Setup Guide (Continued)

Connecting the TLP Pro 320C

The cable connections are located in a panel on the bottom of the TLP Pro 320C:

APower connector — Connect a 12 VDC, 1.0 A power supply (not provided) to this 2-pole, 3.5 mm captive screw connector.

ATTENTION:

• The TLP Pro 320C can use a 12 VDC desktop power supply and is also Power over Ethernet (PoE 802.3af,

class3) compliant. Do not connect either power supply before reading the Attention in the Power Supply sections

of the TLPPro320C User Guide.

• Le TLP Pro 320C peut utiliser une source d’alimentation externe 12 Vcc, et est également compatible avec

l’alimentation POE via Ethernet (PoE 802.3af, classe 3). Ne branchez pas de sources d’alimentation externes

avant d’avoir lu les mises en garde dans la section «PowerSupply» du TLPPro320C User Guide.

NOTE: The TLP Pro 320C ships without a power supply. Either the 12 VDC power supply or the power injector must be

purchased separately.

BNetwork and Power over Ethernet (PoE) Connector — Connect the touchpanel to the LAN using a twisted pair cable,

terminated with an RJ-45 connector. The connector can also be used with a PoE power injector (not provided).

An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.

Product Category

Front Panel Features

To see all the front panel features, remove the bezel, using the Extron Removal Tool (see Included Parts on page 1). For a

complete description of all these features and their function, see the TLP Pro 320C User Guide.

ATTENTION:

• When you slide the removal tool between the screen and the bezel, take care to avoid damaging the ribbon

cable, which runs close to the edge of the bezel.

• Lorsque vous faites glisser l’outil d’extraction entre l’écran et le châssis, faites attention à éviter d’endommager

la nappe de raccordement se trouvant à proximité du bord du châssis.

AABB

EEFFGG

AAmbient light sensor — This sensor monitors ambient light level and adjusts screen brightness, based on the settings

congured using the setup menu (see page 8).

BCommunication LED — This LED shows the conguration and connection status of the touchpanel:

Unlit during normal operation (the touchpanel is congured and connected to an IP Link Pro control processor).

Blinks red if the touchpanel has been congured but is not connected to an IP Link Pro control processor.

Permanently lit if the touchpanel has not been congured.

The indicator can be toggled between enabled and disabled, using the setup menu.

CLCD screen — The TLP Pro 320C has a 3.5 inch screen with a 320x240 resolution.

DConfigurable buttons — 10 dedicated, customizable, function buttons provide quick access to key functions. The buttons

that are supplied with the TLP Pro 320C can be replaced to meet your needs. For information about replacing buttons, see

the TLPPro 320C User Guide.

EReset LED— This LED indicates power status and reset status of the device.

FReset button — This button allows the unit to be reset. The TLP Pro 320C has three reset modes that are initiated by

pressing the reset button (see Reset Modes: a Brief Summary on page 8). For full information about these different modes,

see the TLPPro 320C User Guide.

GMenu button — This button activates the setup menu and calibration screen (see page8).

HBezel — To detach the bezel, use the included removal tool (see the gure to the right, above).

IBezel removal slots — The slots allow removal of bezel, using Extron removal tool.

JIllumination LED — This LED provides light for cable cubby enclosure.

KSpeaker — A single speaker, located inside the cable cubby, provides audible feedback for the user.

68-2516-50 Rev. A

05 15

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

(Inside Europe Only)

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

TLP Pro 320C • Setup Guide (Continued)

Reset Modes: a Brief Summary

The TLP Pro 320C offers the following reset modes (see the TLP Pro 320C User Guide for complete information):

• Use factory firmware: Press and hold the Reset button (see Front Panel Features, F, on page 7) while applying

power to the unit. Use this mode to replace rmware in the event of rmware failure.

• Reset All IP Settings: Press and hold the Reset until the Reset LED (see Front Panel Features, E) blinks twice

(approximately 6 seconds). Release and momentarily press the Reset button. Use this

mode to reset all network settings without affecting user-loaded les.

• Reset to Factory Defaults: Press and hold the Reset button until the Reset LED blinks three times (approximately

9seconds). Release and momentarily press the Reset button. Use this mode to return the

interface to factory default settings.

Setup Menu

The setup menu opens when the menu button is pressed (see Front

Panel Features, G). The image to the right shows the entire Status

screen. Because of size of the touchscreen, you can only see part of

the Status screen at any time. Use your nger to scroll up or down

within the screen.

There are ve different screens: Status, (shown in the gure to the

right) Network, Display, Audio, and Advanced. The screens can be

selected by pressing the Menu button at the top left of the screen

or by pressing the light gray bar with the name of the destination

screen. An arrow to the right of the bar indicates that the bar links

to another screen (for more information about each screen, see the

TLPPro320C User Guide).

Press the Menu button for at least 3 seconds to open the calibration

screen. Follow the on-screen instructions.

Status Exit

INFO

Model:

Part Number:

Firmware Version:

PoE:

TLP Pro 320C

60-1452-02

1.03.0000.b001

Active

NETWORK

DHCP:

Hostname:

IP Address:

TLP-Pro-320C-AB-CD-EF

192.168.254.251

DISPLAY

Screen Resolution: 320x240

Sleep Timer: 5 Minutes

AUDIO

Master Volume

Master Mute: Off

ADVANCED

Controller IP: 192.168.254.250

Storage Usage: 1/151 MB

Bootloader Version: 1.03.0000

Off

Otros manuales para TLP Pro 320C

Tabla de contenidos

Otros manuales de Panel de control de Extron electronics

Extron electronics

Extron electronics ACP 105 EU/MK Manual de usuario

Extron electronics

Extron electronics MKP 2000 Manual de usuario

Extron electronics

Extron electronics IPCP Pro Series Manual de usuario

Extron electronics

Extron electronics CTP150CM Manual de usuario

Extron electronics

Extron electronics RCP 101 D Manual de usuario

Extron electronics

Extron electronics eBUS Button Panel EU Series Manual de usuario

Extron electronics

Extron electronics ACP VC1 EU/MK Manual de usuario

Extron electronics

Extron electronics eBUS Button Panel Decorator-Style Series Manual de usuario

Extron electronics

Extron electronics ACP 106 D Manual de usuario

Extron electronics

Extron electronics NBP 100 Manual de usuario

Extron electronics

Extron electronics ACP 105 D Manual de usuario

Extron electronics

Extron electronics IP Link Pro NBP 50 Manual de usuario

Extron electronics

Extron electronics Control Panel CTL208CM Manual de usuario

Extron electronics

Extron electronics SCP 150L Manual de usuario

Extron electronics

Extron electronics TLP Pro x25M Series Manual de usuario

Extron electronics

Extron electronics TLP Pro 320C Manual de usuario

Extron electronics

Extron electronics AAP 100 Manual de usuario

Extron electronics

Extron electronics MMX 32 AAP Manual de usuario

Extron electronics

Extron electronics MKP 2000 Manual de usuario

Extron electronics

Extron electronics MKP 2000 Manual de usuario

Extron electronics

Extron electronics SCP 104 Series Manual de usuario

Extron electronics

Extron electronics ECP 1000 Manual de usuario

Extron electronics

Extron electronics ACP 100 Manual de usuario

Extron electronics

Extron electronics MCP 1000 Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas