Extron electronics MMX 32 AAP Manual de usuario

Installation Guide

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805

USA

714.491.1500

Fax 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort

The Netherlands

+31.33.453.4040

Fax +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Building

Singapore 368363

+65.6383.4400

Fax +65.6383.4664

Extron Electronics, Japan

Kyodo Building

16 Ichibancho

Chiyoda-ku, Tokyo 102-0082 Japan

+81.3.3511.7655

Fax +81.3.3511.7656

www.extron.com

68-881-01 Rev. C

11 05

Contact Closure Control Panelsfor the MMX 32 VGA A

Mini Matrix Switcher

MMX 32 AAP and

MMX 32 MAAP

Connecting the control panel to an MMX 32 VGA MTP

See the drawing below. The wire connected to the 5 VDC pole

(4on pages 2 and 3) should not be daisy chained. The power for

each AAP or MAAP must come directly from the +5V connector

for the appropriate output on the MMX switcher.

See the drawing below. The wire connected to the Ground pole

(5on pages 2 and 3) should not be shared or jumpered between

two AAPs and/or MAAPs. Run a separate ground wire for each

AAP and/or MAAP. Use the drain wire of the cable for ground.

The drawing below shows a control panel wired to select the input

tied to MMX 32 VGA MTP output 1, using the Remote 1 captive

screw connector. To select the input tied to output 2, use the

Remote 2 captive screw connector.

INPUT 2

INPUT 1

AUDIO

OUTPUT 1

AUDIO

INPUT 3

AUDIO

REMOTE

AUDIO

RS-232

+5V

POWER

12V

0.5A MAX

1 2 3

Tx Rx

SYNC - TRI

PRE PEAK - ON

OUTPUT 2

RGB/AUDIO

MMX 32 AAP

MMX 32VGA MTP

Red +5V

Extron

STP 22 Dual Plenum

Cable 22-162-03

White

CONTACT

Green

Black

Ground ( )

Wiring diagram for a typical MMX 32 VGA MTP application

Recommended Cables

STP22P 1000’ (305 m) Dual Plenum in self-dispensing box 22-162-03

STP22 1000’ (305 m) Dual in self-dispensing box 22-160-03

This guide describes how to connect the Extron MMX 32 architec-

tural adapter plate (AAP) or MMX 32 mini architectural adapter plate

(MAAP) to the MMX 32 VGAAand MMX 32 VGAMTP matrix switchers.

In this manual, the term “switcher” refers to either the

MMX 32 VGA A or the MMX 32 VGA MTP. Where differences

exist, this manual refers to a speciﬁc model by name.

Contact Closure Control

Each Extron MMX 32 AAP and MMX 32 MAAP remote control panel

selects the input for one switcher output via contact closure.

The contact closure system uses the pins on the switcher’s Remote

connector(s) that are not assigned to RS-232 control. Each contact

closure pin corresponds to an input/output connection, or tie. A tie is

made when one pin is connected to ground.

Each pin returns a tally out signal to the remote control panel after a tie

is made, lighting the control panel LED corresponding to the selected in-

put. Power to light the LEDs is provided via the switcher’s Tally Power

(MMX 32 VGAA) or +5V (MMX 32 VGA MTP) connector(s).

The MMX 32 VGA MTP uses a separate 5-pin captive screw

connector for contact closure input selection for output 1 and

for output 2. The pin assignments are clearly marked on the

MMX 32 VGA MTP.

The MMX 32 VGA A uses a DB-9 connector for the connections

(see MMX 32 VGAA pin assignments below).

MMX 32 VGA A pin assignments

The table below shows the contact closure pin assignments for the

MMX 32 VGAA.

For contact closure do not use pins 2 or 3.

Pin RS-232Contact closure noitcnuF

Out #1 / In #1

2TX

11 Transmit data

3 Receive data

Out #1 / In #2

5 Gnd Gnd Signal ground

Out #1 / In #3

Out #2 / In #1

Out #2 / In #2

Out #2 / In #3

Tie input 1 to output 1

Tie input 1 to output 2

Tie input 2 to output 2

Tie input 3 to output 2

Tie input 3 to output 1

Tie input 2 to output 1

—RX—

—

4—

6—

7—

8—

9—

TALLY

PWR

MMX 32 VGA A Remote and Tally Power connectors

Control Panel Connections

To connect a panel to the switcher’s Remote and Tally Power connectors,

wire the captive screw connectors on the rear of the panel as follows.

MMX 32 AAP rear panel

MMX 32 MAAP rear panel

The wire connected to the 5 VDC pole ( 4) should not be daisy

chained. The power for each AAP or MAAP must come directly

from the Tally Power 5V connector on the MMX 32 VGA A

switcher or the +5V connector for the appropriate output on the

MMX 32 VGA MTP switcher.

Input selection connector

1Input 1 pole — Connect this pole of the captive screw connector

to the appropriate connector on the connected switcher:

• MMX 32 VGA A — Remote connector, pin 1 (to control input

selection for output 1) or pin 7 (for output 2)

• MMX 32 VGA MTP — Contact 1 pin 1 (to control input

selection for output 1) or Contact 2 pin 1 (for output 2)

1 MMX 32 AAP andMMX 32 MAAP • Installation Guide

Installation

MMX 32 AAP andMMX 32 MAAP • Installation Guide

Connection

2Input 2 pole — Connect this pole of the captive screw connector

to the appropriate connector on the connected switcher:

• MMX 32 VGA A — Remote connector, pin 4 (to control input

selection for output 1) or pin 8 (for output 2)

• MMX 32 VGA MTP — Contact 1 pin 2 (to control input

selection for output 1) or Contact 2 pin 2 (for output 2)

3Input 3 pole — Connect this pole of the captive screw connector

to the appropriate connector on the connected switcher:

• MMX 32 VGA A — Remote connector, pin 6 (to control input

selection for output 1) or pin 9 (for output 2)

• MMX 32 VGA MTP — Contact 1 pin 3 (to control input

selection for output 1) or Contact 2 pin 3 (for output 2)

Tally Power Connector

45 VDC pole — Connect this pole of the captive screw connector to

the appropriate connector on the connected switcher:

• MMX 32 VGA A — Tally Power connector, 5V pole

• MMX 32 VGA MTP — Contact connector, +5V pole for the

appropriate output.

5Ground pole — Connect this pole of the captive screw connector

to the appropriate connector on the connected switcher:

• MMX 32 VGA A — Tally Power connector, ground pole

• MMX 32 VGA MTP — Contact connector, ground pole for

the appropriate output.

Connecting the Control Panel to the Switcher

INPUT2

INPUT1

AUDIO

OUTPUT1

AUDIO

INPUT3

AUDIO

REMOTE

AUDIO

RS-232

+5V

POWER

12V

0.5AMAX

123

CONTACT

TxRx

SYNC-TRI

PREPEAK- ON

OUTPUT2

RGB/AUDIO

Extron

AAP 102 w/

MMX AAP

Extron

MMX 32 MTP

Matrix Switcher

Laptop

Podium

Computer

Control

Extron

STP 22 Dual Plenum

Cable 22-162-03

Document

Camera

LCD Monitor

with Audio Projector

Audio System

INPUTSELECT

Typical MMX 32 VGA MTP / control panel application

Only one MMX 32 AAP or MMX 32 MAAP control panel can

be used to control each output.

Extron recommends shielded twisted pair cable, such as

STP 22 Dual Plenum cable, part #22-162-03 (or equivalent),

for the connection between the control panel and the switcher.

Unshielded cable can allow crosstalk and interference between the

MMX and the control panel.

Connecting the control panel to an MMX 32 VGA A

See the drawing below. The wire connected to the 5 VDC pole

(4on pages 2 and 3) should not be daisy chained. The power

for each AAP or MAAP must come directly from the Tally Power

connector on the MMX switcher.

See the drawing below. The wire connected to the Ground pole

(5on pages 2 and 3) should not be shared or jumpered between

two AAPs and/or MAAPs. Run a separate ground wire for each

AAP and/or MAAP. Use the drain wire of the cable for ground.

The drawing below shows a control panel wired to select the input

tied to MMX 32 VGA A output 2, using pins 7, 8, and 9 on the

Remote connector. To select the input tied to output 1, use pins 1,

4, and 6 on the Remote connector.

POWER

12V

.5A MAX

INPUT 2

INPUT 1

AUDI O

OUTPUT 1 OUTPUT 2

INPUT 3

AUDI O

REMOTE

AUDI O

TAL LY

OUT

MMX 32 VGA A

MMX 32 AAP

Red +5V

Extron

STP 22 Dual Plenum

Cable 22-162-03

White

Green

Black

Ground ( )

Pins 7, 8, and 9

Wiring diagram for a typical MMX 32 VGA A application

Este manual sirve para los siguientes modelos

Otros manuales de Panel de control de Extron electronics

Extron electronics

Extron electronics MKP 2000 Manual de usuario

Extron electronics

Extron electronics SCP 250 Manual de usuario

Extron electronics

Extron electronics MCP 1000 Manual de usuario

Extron electronics

Extron electronics TLP Pro x25M Series Manual de usuario

Extron electronics

Extron electronics RCP 2000 Manual de usuario

Extron electronics

Extron electronics MLC 55 RS Manual de usuario

Extron electronics

Extron electronics MKP 3000 Manual de usuario

Extron electronics

Extron electronics ACP 105 D Manual de usuario

Extron electronics

Extron electronics ACP 100 Manual de usuario

Extron electronics

Extron electronics MCP 1000 Manual de usuario

Extron electronics

Extron electronics RCP 2000 Manual de usuario

Extron electronics

Extron electronics ACP VC1 D Manual de usuario

Extron electronics

Extron electronics SCP 100P Manual de usuario

Extron electronics

Extron electronics IP Link Pro NBP 50 Manual de usuario

Extron electronics

Extron electronics MKP 2000 Manual de usuario

Extron electronics

Extron electronics IPCP Pro Series Manual de usuario

Extron electronics

Extron electronics NBP 100 Manual de usuario

Extron electronics

Extron electronics eBUS Button Panel Decorator-Style Series Manual de usuario

Extron electronics

Extron electronics TLP Pro 320C Manual de usuario

Extron electronics

Extron electronics Decorator-Style Series Manual de usuario

Extron electronics

Extron electronics TLP Pro 320C Manual de usuario

Extron electronics

Extron electronics RCP 101 D Manual de usuario

Extron electronics

Extron electronics TouchLink Pro Series Manual de usuario

Extron electronics

Extron electronics SCP 104 Series Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas