Extron electronics ACP VC1 D Manual de usuario

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

ACP VC1 D • Setup Guide

The Extron ACP VC1 D Audio Control Panel is a fully congurable control interface for use with any Extron ACP-enabled device.

Each ACP VC1 D includes two ACP ports, which support power and communication between the host device and the

ACP VC1 D. Up to eight ACP panels can be used per host device for more demanding control needs.

Planning System Installation

When planning an ACP system installation, consider how many ACP panels to use, maximum cable distance, and mounting (see

the ACP VC1 D product page at www.extron.com for more information regarding the ACP VC1 D).

MUTE

VOLUME

MUTE

ACP

PWR LOAD = 1.5W

+S -S G +V +S -S G

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

Figure 1. ACP VC1 D

AFront Panel Rotary Volume Knob DConnection Status LED

BFront Panel Mute Button EReset Button

CACP Ports (2) FBus ID DIP Switches

Installation

Step 1: Get Ready

Use the following checklist to prepare for installation:

Download and install the latest software, rmware, and device drivers needed to congure the host device and the

connected ACP devices (see the host device user guide, available at www.extron.com, for details regarding software and

drivers).

Obtain cables, mounting hardware, and any other supplies required for the installation.

ACP VC1 D • Setup Guide (Continued)

Step 2: Prepare the Installation Site

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• Extron recommends installing the ACP VC1 D into a grounded, UL Listed electrical junction box.

• Extron recommande d’installer l’ACP VC1 D dans une boîte de dérivation électrique mise à la terre, certiée UL.

• If the ACP VC1 D will be installed into ne furniture, it is best to hire a licensed, bonded craftsperson to cut the access

hole and perform the physical installation so the surface will not be damaged.

• S’il est prévu d’installer l’ACP VC1 D dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et

qualié pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.

• Follow all national and local building and electrical codes that apply to the installation site.

• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.

NOTE: For the installation to meet UL requirements and comply with National Electrical Code (NEC), the ACP VC1 D must

be installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with the

ACPVC1 D.

Americans with Disabilities Act (ADA) Compliance

When planning where to install these devices, consider factors affecting accessibility of the button panel such as height from

the oor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see sections 307

(“Protruding Objects”) and 308 (“Reach Ranges”) of the 2010 ADA Standards for Accessible Design available at

http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.

Site Preparation

Extron offers an assortment of mud rings, optional ULListed in-wall junction boxes, external wall boxes (EWBs), and surface or

tabletop mounting boxes for use with the ACP button panels. The ACP VC1 D is a US 1-gang size device.

Step 3: Removing the Plastic Faceplate, Removing the Button Panel, and Changing the Button

The plastic faceplate and button can be replaced. Additional

buttons ship with the device and others can be ordered from

www.extron.com.

To change the button:

1. Remove the two screws holding the plastic faceplate to the

metal mounting plate and separate the faceplate from the

button plate (see 1in the figure to the right).

2. Insert a small flat-bladed screw driver into the notch at the top

of the button plate. Release the catch holding the button plate

to the metal mounting plate (2).

3. Repeat step 2 to release the catch at the bottom of the plate.

4. Tilt the top of the button plate forward as it is removed to

prevent the button from falling out.

ACP VC1 D

Faceplate

MUTE

VOLUME

5. To remove the button, press the button backward through its slot in the button

plate until the membrane containing the button is free (see 1 in the figure to the

right).

6. To replace the button, align the two pegs in the button membrane with the

holes located at opposite corners of the empty slot on the back of the button

faceplate and push the button forward so it fits in the slot (2). Ensure the

button text orientation is correct.

7. Align the button plate with the metal mounting plate using the pegs on the rear

of the button plate as guides.

8. Snap the button plate into place.

9. Reattach the plastic faceplate using the two screws removed in step 1 on the

previous page.

Step 4: Set Bus ID Address

Set the bus identication (bus ID) DIP switches for the ACP VC1 D and any other

ACP panels being connected to the system. Each ACP device must have a unique

bus ID. If multiple panels have the same bus ID, address conicts may cause one

or more of the panels to not be recognized in DSP Congurator or by the

host device. Up to eight ACP devices can be connected in the same system.

+VG

+S-S+VG

+S-S

ACP

PWR LOAD = 1.5W

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

V+

S G

–

010010

123456

000001

123456

Unit address

DIP switches

Binary addressACP port on a

DMP 128 Plus, or

on another ACP

endpoint

ACP Ports

• Connect up to eight (8) ACP endpoint devices per

DMP 128 Plus.

• Wire the connectors the same at both ends.

• These ports are identical. You can connect devices

interchangeablly to either port.

• Do not exceed a total of 1000 feet (305meters) of cable for

connections between the DMP 128 Plus and all of the ACP

panels.

• Power is provided by the IPCP Pro, a PS 1220EB power

inserter, or an Extron 12 VDC power supply.

Bus ID Address DIP Switches

• Use these DIP switches to set the six-bit, binary

bus address for the ACP 100.

• Each ACP connected to the same DMP 128 Plus

must have a unique address.

• Switch 1 (on the left) is the highest value (32, the

the most signicant bit [labeled “MSB”]).

• Switch 6 (on the right) is the lowest (1, the least

signicant bit [labeled “LSB”]).

• Up = on = 1, Down = off = 0

Examples:

MUTE

ACP VC1 D • Setup Guide (Continued)

Setting the Bus ID Address

Each ACP device in a system must have a unique six-digit binary bus ID. ACP bus

IDs are set using the DIP switch assembly on the left side of the ACP VC1 D (see

Eon gure 1 at the beginning of the guide).

Switch 1 on the left sets the most signicant bit (highest number, 32) while switch

6 on the right sets the least signicant bit (the lowest number, 1). See the example

addresses to the right.

Step 5: Cable All Devices

1. Connect the ACP panel to the host device.

2. Connect ACP panels to each other if multiple panels are used in the system

(see the wiring diagram below for correct wiring).

NOTES:

• Wire both ends of each ACP cable the same. Connectors are

interchangeable between the host device and ACP devices.

• Do NOT power an ACP panel from more than one power source.

3. Apply power to the host device after correctly cabling all devices.

Cabling

Attach cables using the diagram below as a guide. Wiring is the same for all ACP

models. Connect a 4-pole captive screw connector to each end of the cable,

wiring both ends the same. In most cases, ACP devices are powered by the host

device. Power is carried on the V+ pin of the ACP VC1 D and other ACP devices.

Extron STP20-2/1000 or STP20-2P/100 cable is recommended for ACP device

connections.

ACP devices that are relatively far from the host device can be connected to an

optional Extron PS 1220EB eBUS power inserter or an Extron 12 VDC desktop

power supply as shown in the diagrams below and on the next page (see the ACP

VC1 D Specications at www.extron.com to determine if additional power is

recommended).

Example Addresses

Bus ID

(Decimal)

Binary

Address

DIP Switch

Setting

0 000000*

*Reserved

(for controller

address)

1 2 3456

BUS ID

1 000001

1 2 3456

BUS ID

2 000010

1 2 3456

BUS ID

3 000011

1 2 3456

BUS ID

4 000100

1 2 3456

BUS ID

5 000101

1 2 3456

BUS ID

6 000110

1 2 3456

BUS ID

7 000111

1 2 3456

BUS ID

8 001000

1 2 3456

BUS ID

Ground

+Signal

Signal

+12 VDC

Black

and

Drains

Green

White

Red

S+S

Drain Wires

Basic ACP Connector Wiring

ATTENTION:

• Always use a power supply supplied or specied by Extron. Use of an unauthorized power supply voids all regulatory

compliance certication and may cause damage to the supply and the unit.

• Utilisez toujours une source d’alimentation fournie par Extron. L’utilisation d’une source d’alimentation non autorisée

annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi que l’unité.

• If not provided with a power supply, this product is intended to be supplied by a UL Listed power source marked

“Class2” or “LPS” and rated output 12VDC, minimum 1.0A.

• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit être alimenté par une source

d’alimentation certiée UL de classe 2 ou LPS et paramétré à 12VDC et 1,0A minimum.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces d’aération

ou dans les cavités murales.

• The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA70,

article725 and the Canadian Electrical Code part1, section16. The power supply shall not be permanently xed to

building structure or similar structure.

• L’installation doit toujours être conforme aux dispositions applicables du Code américain de l’électricité (National

Electrical Code) ANSI/NFPA 70, article 725, et du Code canadien de l’électricité, partie1, section16. La source

d’alimentation ne devra pas être xée de façon permanente à une structure de bâtiment ou à une structure similaire.

• Only for use with Extron’s UL Listed IPCP Pro Controller products or ACP-enabled devices.

• À utiliser uniquement avec les contrôleurs IPCP Pro Extron certiés UL ou des produits équipés ACP.

eBUS 24 WATTS MAX

100-240V 50-60Hz

0.6A MAX

V+

S G

–

V+

S G

–

S+

V+

S G

–

S+

V+

S G

–

V+

S G

–

S+

V+

S G

–

ACP port on

another ACP

endpoint

device

V+

S G

–

LAN

DMP 128 Plus C

RxTx G

RS-232

+S+V -S G

5 6 7 8

1 2 34

OUTPUTS

DMP EXP

ACP

REMOTE

USB AUDIO RESET

DMP 128 Plus

S+S

Tie drain wires

to ground.

S+S

Ground

+Signal

Signal

+12 VDC

S+S

Power Input

(100-240 VAC,

50-60 Hz)

PS 1220EB

ATTENTION: Do NOT connect the power

pin to any device that is already powered

by the DMP 128 Plus control processor

or by an additional power supply.

3/16" (5 mm) Max.

ACP Connections

• Connect up to eight (8) ACP

endpoint devices to the PS 1220EB.

• Wire the connectors the same at

both ends.

• All ports are identical and

interchangeable.

ACP VC1 D • Setup Guide (Continued)

External Power Supply

(12 VDC, 2.0 A)

ACP 105 D

Rear Panel

Tie drain wires to ground.

Ground

all Devices

RidgedSmooth

3/16" (5 mm) Max.

ACP port on

a host DMP

128 Plus

ACP port on

an ACP or

other ACP

Endpoint

NOTE:

Check the polarity of the power

supply before connecting it to the ACP.

V+

S G

–

V+

S G

–

Ground

+Signal

Signal

Ground

+Signal

Signal

+12 VDC

– Return

+12 VDC input

+VG

+S-S+VG

+S-S

ACP

PWR LOAD = 1.5W

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

Power Input, External Power Supply (optional)

• Connect to an Extron 12 VDC, 2.00 A, power supply.

Step 6: Conﬁgure the System

NOTE: For complete information on creating configuration files and operating DSP Configurator Software, see the

host device user guide or refer to the DSP Configurator Software product page at www.extron.com.

1. Create a new host device configuration file in DSP Configurator and create all groups, presets, and macros to be controlled

by the ACP device.

2. Select Tools>Configure ACPs in DSP Configurator and configure the ACP button actions and panel IDs.

3. Connect to the host device in Live mode with a TCP/IP connection and push the configuration file to the device.

Step 7: Test and Troubleshoot

1. Verify the ACP bus ID DIP switches are set to the desired address on each unit and that there are no bus ID address conflicts

in the system. As mentioned in the rear panel features diagram in step 4 (see page 3), the ACP LED lights green when power

and communication are present and there are no bus ID address conflicts. Refer to the legend on the back of the panel for

other LED behavior indications.

2. Verify cables to and from the ACP devices are wired the same at each end.

3. Test the system:

a. Press the ACP device button and ensure the button lights as expected and that the appropriate control actions are

triggered. Commands can be verified using DSP Configurator. DataViewer can also be used for command verification if

responses are configured.

b. Ensure the audio levels respond correctly to the rotary volume control and mute button.

4. Make adjustments to wiring, bus ID addresses, and system configuration as needed. Remember that the rear panel ports and

DIP switches are not accessible after the ACP is mounted. If needed, push a revised configuration to the ACP device through

the host device using DSP Configurator.

If you have questions during installation and setup, call the Extron S3 Sales and Technical Support Hotline or the Extron S3

Control Systems Support Hotline (1.800.633.9877).

Step 8: Mounting the ACP VC1 D

Prior to mounting:

1. Feed all device cables through the wall or furniture.

NOTE: If the unit is not installed in a mud ring, the plastic spacer must be installed. The spacer positions the unit to allow

the plastic faceplate to attach properly and securely.

2. Ensure the cables are connected to the ACP VC1 D rear panel.

To mount an ACP VC1 D with a wall mounting bracket (mud

ring):

1. Mark the position of the hole for the wallplate on desired

wall location. Use a level to ensure the hole is marked at the

correct angle.

2. Use a drywall saw to cut the hole for the wall mounting

bracket (see 1in the figure to the right).

3. Insert the wall mounting bracket (mud ring) into the hole and

use a screw driver to turn and tighten the locking arms until

they clamp the mud ring to the mounting surface (2). Do not

overtighten.

4. If not already done, set bus ID DIP switches so the panel has a

unique bus ID (3).

5. Use the two provided screws to secure the metal mounting

plate to the mud ring (4).

6. Use the other two provided screws to secure the plastic

faceplate to the metal mounting plate (5).

To mount an ACP VC1 D with a junction box:

1. Install the junction box following the instructions provided with

the chosen junction box. No junction box is included with the

ACP VC1 D.

2. Locate a suitable wall stud and mark the location of the hole on

the wall. Use a level to ensure the hole is marked at the correct

angle.

3. Use a drywall saw to cut the hole. Follow the instructions of

the junction box manufacturer for the correct dimensions of the

hole. Use at least two screws or nails to secure the box to the

wall or stud. Follow steps 4 through 6 above to complete the

installation.

Wall

Wall Mounting

Bracket

MUTE

VOLUME

Faceplate

ACP VC1 D

Electrical

Junction

Box

MUTE

VOLUME

ACP VC1 D

Faceplate

68-3420-50 Rev. A

04 19

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Tabla de contenidos

Otros manuales de Panel de control de Extron electronics

Extron electronics

Extron electronics CTP150CM Manual de usuario

Extron electronics

Extron electronics RCP 101 D Manual de usuario

Extron electronics

Extron electronics ACP 106 D Manual de usuario

Extron electronics

Extron electronics eBUS Button Panel EU Series Manual de usuario

Extron electronics

Extron electronics MKP 2000 Manual de usuario

Extron electronics

Extron electronics RCP 2000 Manual de usuario

Extron electronics

Extron electronics SCP 100P Manual de usuario

Extron electronics

Extron electronics MCP 1000 Manual de usuario

Extron electronics

Extron electronics TLP Pro x25M Series Manual de usuario

Extron electronics

Extron electronics TLP Pro 320C Manual de usuario

Extron electronics

Extron electronics NBP 100 Manual de usuario

Extron electronics

Extron electronics TLP Pro 320C Manual de usuario

Extron electronics

Extron electronics MCP 1000 Manual de usuario

Extron electronics

Extron electronics MLC 55 RS Manual de usuario

Extron electronics

Extron electronics ACP 100 Manual de usuario

Extron electronics

Extron electronics ACP 105 D Manual de usuario

Extron electronics

Extron electronics IPCP Pro Series Manual de usuario

Extron electronics

Extron electronics RCP 101 EU Manual de usuario

Extron electronics

Extron electronics MKP 2000 Manual de usuario

Extron electronics

Extron electronics ACP 100 Manual de usuario

Extron electronics

Extron electronics MKP 2000 Manual de usuario

Extron electronics

Extron electronics MLC Plus 84 EU Manual de usuario

Extron electronics

Extron electronics TouchLink Pro Series Manual de usuario

Extron electronics

Extron electronics SCP 150L Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas