Extron electronics NetPA U 8001 SUB Manual de usuario

NetPA U 8001 SUB • Setup Guide

The Extron NetPA U 8001 SUB is an ENERGY STAR-qualied, Dante-enabled subwoofer amplier with onboard audio DSP,

designed specically for use with the Extron SF 10C SUB in-ceiling subwoofer speaker, as well as other 8, 4, or 2 ohm

subwoofers with similar power requirements. The NetPA U 8001 SUB can deliver up to 800 watts at 8 ohms, 650 watts at 4 ohms,

or 325 watts at 2 ohms.

The NetPA U 8001 SUB is 1U high, half-rack width, and rack-mountable. The amplier has mounting holes for 9-inch (22.86 cm)

and deeper rack shelves, and is plenum-rated with an optional ex conduit adapter. The unit is convection-cooled.

This guide provides instructions for an experienced installer to set up and operate the NetPA U 8001 SUB subwoofer amplier.

For full installation, conguration, and operation details, see the NetPA U 8001 SUB User Guide available at www.extron.com.

Installation Steps

Step 1 — Mounting onto a Rack

Turn off all of the equipment and disconnect it from the power source. Mount the amplier as required. It can be securely mounted

in a variety of locations, using optional Extron Mounting Brackets and accessories (see the Extron website for compatible

optional mounting accessories), or using the included three-piece bracket system. The brackets do not come attached to the

amplier.

The following sections describe two methods of rack-mounting the ampliers.

Rack Ear Mounting (Single Unit)

The NetPA U 8001 SUB amplier ships with a set of rack ears, so this half-rack width amplier can be installed in a full-rack width

space. Mount the amplier with rack ears as follows:

1. If the amplier has its rubber feet installed, remove them.

2. Attach the rack brackets (one long and one short) to the sides with the four provided #6 machine screws (1).

3. Insert the amplier into the rack and align the holes in the rack ears with the holes on the rack.

4. Secure the amplier to the rack using the four provided 10-32 x 3/4-inch screws (2).

NetPA U 800 1 SUB

OVER

TEMP LIMITER/PROTECT

SIGNAL

POWER AMPLIF IERS

Net PA U 8001 SUB

OVER

TEMP LIMITER/PROTECT

SIGNAL

POWER AMPLIFI ERS

Figure 1. NetPA U 8001 SUB Rack Ear Mounting

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

Bridge Plate Rack Mounting (Side-by-Side)

The NetPA U 8001 SUB ships with a bridge plate connector to connect two ampliers together and form a full-rack width unit.

Mount and connect two ampliers as follows:

1. If the amplier has its rubber feet installed, remove them.

2. Position two ampliers upside down and side-by-side as shown below.

3. Use the bridge plate connector and the four provided #4 machine screws to connect the two units together (1).

4. Attach the two short rack ears to the units with the four provided #6 machine screws (2).

5. Insert the amplier into the rack and align the holes in the rack ears with the holes on the rack.

6. Secure the amplier to the rack using the four provided 10-32 x 3/4” screws (3).

Mounting

screws (4)





NetPA U 8 001 SUB

OVER

TEMP LIMITER/PROTECT

SIGNAL

POWER AMPL IFIERS

NetPA U 8 001 SUB

OVER

TEMP LIMITER/PROTECT

SIGNAL

POWER AMPL IFIERS



Net PA U 8001 SUB

OVER

TEMP LIMITER/PROTECT

SIGNAL

POWER AMP LIFIERS

Net PA U 8001 SUB

OVER

TEMP LIMITER/PROTECT

SIGNAL

POWER AMP LIFIERS

Figure 2. NetPA U 8001 SUB Bridge Plate Rack Mounting

In addition to rack-mounting, the NetPA U 8001 SUB can also be mounted directly to the SF 10C SUB using the mounting

hardware that is included with the speaker. Please see the NetPA U 8001 SUB User Guide for detailed setup instructions.

Ventilation Recommendation

Excessive heat decreases the optimal lifetime of the power amplier. An

Over Temp LED indicator on the front panel of the amplier lights red when

the recommended operating temperature has been exceeded.

NetPA Ultra ampliers need to be arranged in a rack environment, so that

the environment around the amplier does not reach or exceed +122 °F (+50

°C). No more than four ampliers in a group should be stacked without a

ventilation opening between the groups.

The NetPA U 8001 SUB can also be arranged above or below a non-NetPA

Ultra device, but in any case, the environment should never reach or exceed

+122 °F (+50 °C).

Vent Space

NetPA U 8001 SUB • Setup Guide (Continued)

Step 2 — Captive Screw Audio Cable Wiring

Wire the captive-screw connectors to the input or output as shown in the following gures.

Unbalanced Stereo Input

Balanced Stereo Input

Tip

Ring

Tip

Ring

Sleeves

Tip

Sleeve

Tip

Sleeve

No Ground Here

Tip

Ring

Sleeve

Balanced Mono Input

Tip

Sleeve

Tip

Ring

Tip

Ring

Sleeves

Unbalanced Mono Input

Balanced Output

OUTPUT

Unbalanced Output

Do not tin

the wires!

(5 mm) MAX.

3 "

Figure 3. Line Input and Line Output Wiring

ATTENTION:

• For unbalanced audio outputs, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative

(-) contacts.

• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux contacts

négatifs (–).

Step 3 — Remote Ports

STANDBY

REMOTE

STANDBY

Tx Rx G

RS-232

Do not tin

the wires!

(5 mm) MAX.

3 "

Figure 4. Remote Volume Control and Standby Ports

• Standby mode is forced when the Standby pin is connected to the second G pin. The power LED on the front panel

lights amber when the amplier is in Standby mode, indicating that the amplier is still receiving power despite the fact

that it has turned off all the outputs.

NOTE: The enabling and disabling of the auto-standby timer is handled through SIS or DSP Configurator. For more

details, consult the NetPA U 8001 SUB User Guide.

• Connect a 3.5 mm, 3-pole captive screw connector to remotely control the volume via SIS commands, and connect a 3.5

mm, 2-pole captive screw to place the amplifier into Standby mode.

Protocol for the RS-232 port:

• 38,400 baud • 1 stop bit • 8 data bits • no parity

Step 4 — Speaker Wiring

Connect a 2-pin, 5 mm captive-screw connector for speaker output on the NetPA U 8001 SUB amplier. The port has a screw

ange to secure the plug to the connector (see ﬁgure 5 to learn how to wire the captive screw connector).

OUTPUTS

CLASS 2 WIRING

8Ω/4Ω

CH 1

Figure 5. Speaker Output Port and Wiring Diagram

ATTENTION:

• You must use Class 2 wiring for this output to comply with UL requirements.

• Vous devez utiliser le câblage de classe 2 pour cette sortie an de vous conformer aux exigences UL.

• Do not tie channel output pins to each other or to ground. Doing so will short out the outputs, damage the

amplier, or both.

• Ne pas lier les sorties 1 et 2 des canaux entre elles ou à la terre. Les sorties pourraient être court-circuitées et/

ou l’amplicateur pourrait être endommagé.

• To avoid risk of damage to the amplier or the speakers, always check that speaker loads are appropriately

wired to the amplier.

• Pour éviter les risques de dommages à l’amplicateur ou aux haut-parleurs, vériez toujours que les charges

des haut-parleurs sont correctement câblées à l’amplicateur.

Step 5 — AT Port

Connect an RJ-45 connector to the AT port to connect and

communicate with the Dante network. It is also one of the

interfaces DSP Congurator uses to communicate with the

amplier. The Link LED indicates when a connection is made.

Go to Configure Dante Device Settings on page 5 for

information on Dante settings. See the image to the right for

wiring.

Step 6 — Powering on Ampliﬁer and Adjustments

Ensure all sources connected to the amplier inputs are muted to

avoid potential speaker damage during power-up.

Reconnect all the power cables and switch on the rest of the

equipment before powering on the power amplier. The amplier

boots-up for up to 10 seconds as the front panel LED ashes green.

Once the boot-up sequence is complete, the amplier takes more time to sync with the Dante network, and begin the

playback of streamed content. The front panel LED lights green after approximately 20 seconds.

ATTENTION:

• The amplier must be powered on last.

• L’amplicateur doit être mis sous tension en dernier.

Step 7 — Checking LEDs

Check the Limiter/Protect and Signal LEDs on the front and rear panels to see if any problems are encountered (see “Front

Panel Features and Troubleshooting” in the NetPA U 8001 SUB User Guide for more information).

Double-check the correct load is connected and properly wired to the rear panel connection (see Speaker Wiring on page 3

for more information).

Step 8 — DSP Conﬁgurator Software Installation

There are no hardware controls for the NetPA U 8001 SUB. Conguration is performed using Extron DSP Congurator

software, while control is performed via SIS commands. To learn about full computer requirements, see the DSP Congurator

product page on www.extron.com.

Download DSP Conﬁgurator from the Extron Website

1. From the Extron home page (www.extron.com), click the Download tab to open the Download page.

2. Under Software (located on the left side of the page), select DSP Congurator Software. The DSP Configurator

Software product page opens.

3. Click the Download button and follow the on-screen instructions.

12345678

RJ-45

Connector

Insert Twisted

Pair Wires

Pins:

A cable that is wired as TIA/EIA T568A at one

end and T568B at the other (Tx and Rx pairs

reversed) is a "crossover" cable.

T568B T568A

Crossover Cable

(for direct connection to a PC)

End 1 End 2

Pin Wire Color Pin Wire Color

1 white-orange 1 white-green

2 orange 2 green

3 white-green 3 white-orange

4 blue 4 blue

5 white-blue 5 white-blue

6 green 6 orange

7 white-brown 7 white-brown

8 brown 8 brown

NetPA U 8001 SUB • Setup Guide (Continued)

NOTE: An Extron Insider account is required to download DSP Configurator.

Step 9 — NetPA U 8001 SUB Conﬁguration

When power is connected to the unit and the rest of the audio system, audio output can be easily configured to any listening

environment via the DSP Configurator. The following steps detail how to configure a NetPA U 8001 SUB amplifier.

Conﬁgure the NetPA U 8001 SUB Ampliﬁer

1. Ensure the control computer is

connected to either the AT port,

RS-232 port, or the rear panel USB

conguration port.

2. Start the DSP Congurator software.

From the splash screen drop-down list,

select NetPA U 8001 SUB. Click OK.

The main workspace opens.

3. The software starts in Emulate mode:

a. To create a conguration le ofine

and then upload that conguration

to a NetPA U 8001 SUB unit at a

later time, remain in Emulate mode and save the conguration le.

b. To upload a conguration to the NetPA U 8001 SUB unit or download the current conguration from the unit, enter Live

mode. When in Live mode, changes made in DSP Congurator immediately affect the connected NetPA U 8001 SUB. To

enter Live mode, click Live at the top of the DSP Congurator workspace, or select Tools >Connect to Device,or

press <F6> on the keyboard.

NOTE: When Live mode is selected, a connection dialog box appears. Select the desired connection type and follow

the on-screen prompts (see the NetPA U 8001 SUB User Guide for more information on connecting live to a device).

The main workspace provides access to mix matrices, gain blocks, and DSP processors (including a crossover lter)

for conguring a NetPA U 8001 SUB. It also provides a menu bar across the top with additional conguration tools. For

more information on using the DSP Congurator, see the “DSP Congurator” section of the NetPA U 8001 SUB User

Guide, or the DSP Conﬁgurator Help File that can be accessed by selecting Help >Contents or pressing <F1>. Most

dialog boxes within DSP Congurator contain a Help button ( ) in the top right corner. Click this button to open the

help le topic for that particular dialog box.

Downloading and Installing Dante Controller

1. From www.extron.com, hover over the Download tab at the top of the page.

2. From the Featured Software list, select Dante Controller. The Dante Controller product page opens.

3. Click the blue Download button.

4. Select Run to run the Dante Controller installer or select Save to save the install le to run at a later time.

5. If you choose to run the le, follow all prompts. If you saved the le, click the saved le to begin installation when ready.

NOTE: The installed Dante Controller program files are saved in:

C:\Program Files (x86)\Audinate\Dante Controller\DanteController.exe.

Conﬁgure Dante Device Settings

Dante settings in the NetPA U 8001 SUB can be congured from DSP Congurator. The device can be named in the Dante

Device Settings, which assists with identifying a specic device in the Dante Controller software when there are multiple

devices on the Dante network.

ATTENTION:

• It is crucial that a Dante device be named before audio subscriptions with other devices are established. Existing

subscriptions are removed when a unit is renamed.

• Il est crucial qu’un appareil Dante soit nommé avant la création d’abonnements audio avec d’autres appareils. Les

abonnements existants sont supprimés lorsqu’une unité est renommée.

To conﬁgure Dante device settings:

1. Open DSP Congurator and connect live to the NetPA U 8001 SUB.

2. Select Tools >Device Settings. The Device Settings dialog box opens.

3. From the tabs at the top of the Device Settings dialog box, select Dante Device.

4. In the Device Name eld, give the NetPA U 8001 SUB a name (recommended to be device model and location) so that it can

be easily identied in Dante Controller. No spaces are allowed in the name.

5. Dante device network settings can also be congured in this dialog box. Use the radio buttons and text elds to choose

DHCP (recommended) or Static IP and enter a static IP address conguration.

6. Click Apply.

7. Click OK to conrm changes and close the Device Settings dialog box.

Renaming the NetPA U 8001 SUB Ampliﬁer in Dante Controller

1. From the control computer Start menu select: All Programs > Audinate > Dante Controller > Dante

Controller

2. The Dante Controller -Network View screen opens. All Dante devices on the network are discovered and listed.

3. From the Device menu, select Device View or press <Ctrl+D> on the keyboard.

4. The Dante Controller -Device View dialog opens. Select the device being congured from the (Select aDante

Device...) drop-down list. The Device View dialog populates with the selected NetPA U 8001 SUB information.

Figure 6. Populated Device View Dialog Box

5. Click the Device Cong tab to open the Device Config page.

6. In the Rename Device panel, enter the new name of the device in the text eld.

NOTE: No spaces are allowed in the name and names should be significant identifiers. For example,

NetPAUAmplifier-MainRack

7. Click Apply. A conrmation prompt opens.

8. Click Yes to conrm the new name.

9. Repeat as necessary for all devices.

Creating a Physical Dante Network

A physical network is required to share Dante audio channels

among Dante-enabled devices like those found in the NetPA

U 8001 SUB. Other devices capable of sending and receiving

audio over a Dante network must be on the same physical

network in order to communicate with Dante (see gure 7 on

the right for an example of a Dante network).

AUDIO

NetPA U 8001 SUB

LIMITER/PROTECT

SIGNAL

OVER

TEMP

XPA U 1002 SERIES

LIMITER/PROTECT

SIGNAL

OVER

TEMP 21

POWERAMPLIFIERS

Ext

ron

26CT

Spea

kers

Extron

XPA U 1002-70V

Power Amplier

Extron

WPD 101 3.5 mm

Single Gang

Pass-Through

Wallplate

Extron

NetPA U 8001 SUB

Subwoofer Amplier

800 Watt @ 8Ω

Line Inputs

Audio Line Out

Audio

Ethernet

Extron

SF 10C SUB

Subwoofer

Figure 7. Example of a Dante Network

NetPA U 8001 SUB • Setup Guide (Continued)

Dante Network Setup

Use a standard Ethernet cable to connect a NetPA U 8001 SUB amplier to a Dante network via the AT port. Launch the

Dante Controller program.

Dante Controller automatically discovers all Dante devices on the network and allows other Dante-enabled devices to

communicate with it. The default device name is the model name followed by the last six characters of the device MAC address

(for example, NetPA-U-xxxxxx). Multiple devices on the same network can present difculty in identifying inputs and outputs. To

avoid confusion, rename each device to a unique identier.

NOTE: To simplify setup, connect only one Dante device to the network at a time.

Dante Controller Operation

Dante Transmitters and Receivers

A Dante network is comprised of transmitters that output digital audio onto the Dante network and receivers that receive

digital audio input from the Dante network.

• Transmitters output digital audio from the device onto the audio network.

• Receivers take in digital audio from the audio network into the device.

Network View Layout

In the Dante Controller software, Dante transmitters are

listed horizontally across the top of the Network View

(1), while Dante receivers are listed vertically on the left

side of the window (2). Creating a link in the connection

matrix routes audio from a transmitter to a receiver (3).

Routing Devices

1. To show the transmitters of a Dante device, click

the +box next to the desired device in the Dante

Transmitters panel, such as

NetPA-U-Classroom-1 (1). The +changes to a –

sign when the details for the device expand.

2. To show the receivers of a Dante device, click the

+box next to the desired device in the

Dante Receivers panel, such as DMP128P-PD-Control-Room (2).

3. Click the intersection of the desired subscription (discrete connection) between a transmitter and a receiver (3). A check

mark at the intersection indicates the subscription is made. A check mark also appears next to the receiver channel.

NOTE: A receiver can subscribe to only one transmitter. A transmitter can connect to multiple receivers.

4. To undo routing, click the junction again to disconnect the receiver from the transmitter.

NOTE: After making changes to Dante network routing such as subscriptions, device names, or channel labels, wait at

least 5 seconds before disconnecting or powering down the devices. This ensures that the new information is properly

saved to those devices. Device-level configurations, such as sample rates, latency, and clock settings are saved

instantly.

For more information on conguring a NetPA U 8001 SUB unit in Dante Controller, see the “Dante Controller” section of the

NetPA U 8001 SUB User Guide found on www.extron.com.

NetPA U 8001 SUB • Setup Guide (Continued)

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Gain Structure

The input sensitivity of the NetPA U 8001 SUB amplier is 0 dBFS. To achieve maximum output power without degrading audio

clarity, the peak signal level on the meter at the amplier channel output attenuators should be set at—or as close as possible—to

0 dBFS.

The default conguration of the DSP blocks are as follows:

• Input Signal Chain

• All analog input gains (ANG GAIN) are set to 0 dB.

• All Dante inputs do not have an input gain inserted.

• All processors are disabled.

• All input pre-mix gains are set to 0 dB.

• Mix Points

• Analog inputs are mixed at -6 dB to the amplier output channel and mixed at 0 dB to the AT outputs.

• AT inputs are mixed at -6 dB to the amplier output and at 0 dB to the Line outputs.

• Output Signal Chain

• All output trims are set to 0 dB.

• Amplier channel output attenuator is set to -24 dB.

• Line and AT output attenuators are set to 0 dB.

Setting-Up Gain Structure

Setting proper gain structure is necessary to ensure maximum audio clarity and amplier output performance. To set-up gain

structure, follow the steps outlined below, using a calibrated pink noise source.

1. Ensure all pre-mix gain and output trim blocks are set to 0 dB.

2. If mixing a stereo input to the subwoofer output, set mix point gain to -6 dB for each input channel. If mixing a mono input to

the amplier output, set mix point gain to 0 dB.

3. Adjust the Line Input ANG GAIN blocks so the output meter reads -17 dBFS.

4. Adjust the output attenuators, so the output meter reads -17 dBFS.

Refer to the NetPA U 8001 SUB User Guide found on www.extron.com for more details on setting-up gain structure.

NOTE: When setting levels, pay attention to avoid digital clipping.

Crossover Filter

One lter block is available for each output channel. This lter block offers a crossover lter that links the parameters of two (one

high-pass and one low-pass) or three (two high-pass and one low-pass) output lters. To apply a crossover lter to the output

channel, follow the procedure found in the NetPA U 8001 SUB User Guide.

68-3414-50 Rev. A

11 2020

Tabla de contenidos

Otros manuales de Amplificador de Extron electronics

Extron electronics

Extron electronics NetPA Ultra Series Manual de usuario

Extron electronics

Extron electronics P/2 DA2 EC F Manual de usuario

Extron electronics

Extron electronics XPA U 3502 Manual de usuario

Extron electronics

Extron electronics IN3254 Manual de usuario

Extron electronics

Extron electronics XPA U 2004 FX Manual de usuario

Extron electronics

Extron electronics XPA 1002 Manual de usuario

Extron electronics

Extron electronics MPA 152 MD Manual de usuario

Extron electronics

Extron electronics DA 6SV EQ Manual de usuario

Extron electronics

Extron electronics DA 12V/6V Dual EQ Manual de usuario

Extron electronics

Extron electronics VersaTools MDA 5A RCA Manual de usuario

Extron electronics

Extron electronics VGA Distribution Amplifiers P/2 DA4xi s Manual de usuario

Extron electronics

Extron electronics P/2 DA2 MT Manual de usuario

Extron electronics

Extron electronics MDA EQ Series Manual de usuario

Extron electronics

Extron electronics MDA 4V EQ Manual de usuario

Extron electronics

Extron electronics XPA 1002 Manual de usuario

Extron electronics

Extron electronics HDMI DA2 Manual de usuario

Extron electronics

Extron electronics MPA 181T Manual de usuario

Extron electronics

Extron electronics ASA Series Manual de usuario

Extron electronics

Extron electronics Two Output 13W3 Sun and SGI Distribution Amplifier 13W3... Manual de usuario

Extron electronics

Extron electronics VersaTools MDA 3 Series Manual de usuario

Extron electronics

Extron electronics XPA 2001-70V Manual de usuario

Extron electronics

Extron electronics Extron P/2 DA2xi Manual de usuario

Extron electronics

Extron electronics Video and Audio Line Drivers with Gain and EquaLization CVEQ... Manual de usuario

Extron electronics

Extron electronics XPA 1002 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario