Extreme Networks BlackDiamond 6816 Manual de instalación y operación

Part Number: 121069-00 Rev 01 1

MSM-3 Upgrade Note

This note describes the minimum requirements and upgrade procedures for the BlackDiamond®

MSM-3. For complete product documentation, see:

http://www.extremenetworks.com/go/documentation_main.htm

BootROM 8.1 and ExtremeWare 7.1.1 Required

The MSM-3 requires both BootROM 8.1 (or later) and the final release build of ExtremeWare 7.1.1 (or

later). Builds prior to the final release might not fully support the MSM-3.

You can obtain BootROM 8.1 and ExtremeWare 7.1.1 from the Extreme Networks website at:

http://www.extremenetworks.com/go/esupport.htm

Enter your username and password from your current support contract. Once logged in, select Software

Download and download the files.

You can contact Extreme Networks Customer Support at: (800) 998-2408 or (408) 579-2826.

Upgrade Your Chassis

You need the following tools and equipment to install an MSM-3:

•ESD-preventive wrist strap

•# 1 Phillips screwdriver

•MSM-3

To install an MSM-3 in a new chassis, simply follow the installation instructions in the BlackDiamond

Module Installation Note included with your MSM-3. To upgrade your chassis from MSM64i’s to

MSM-3’s:

1Preserve Your Existing Configuration

2Upgrade to MSM-3’s

3Verify the Installation

These procedures are described in the following sections.

2MSM-3 Upgrade Note

Upgrade Your Chassis

CAUTION

Service to BlackDiamond modules should be performed by trained service personnel only. Before

installing or removing any components of the system, or before carrying out any maintenance

procedures, you must read the safety information provided in Appendix A of the Extreme Networks

Consolidated Hardware Guide.

Preserve Your Existing Configuration

To preserve your existing configuration, follow these steps:

1Upgrade the MSM64i’s to ExtremeWare 7.1.1 (or later) and BootROM 8.1 (or later). Follow the

instructions in the Release Notes for the release you are installing.

2Make any configuration changes required by the upgrade.

3Save the configuration using the save configuration command.

4Upload the configuration to a TFTP server using the upload configuration command.

5Verify that the uploaded file is complete.

6Start a console log.

7Capture the real-time status of the switch using the show tech-support command.

8Stop the console log.

Upgrade to MSM-3’s

To upgrade your chassis from MSM64i’s to MSM-3’s:

1Attach the ESD strap to your wrist and connect the metal end to the ground receptacle that is located

on the top-left corner of the switch front panel.

2Remove the slave MSM64i. On a BlackDiamond 6816, remove all slaves.

3Insert the MSM-3. On a BlackDiamond 6816, insert MSM-3’s into all empty slots. Each MSM-3

initializes as a slave MSM.

NOTE

Using an MSM64i and MSM-3 in the same chassis is supported during the upgrade process only. If

you use both MSMs in the same chassis, the switch does not operate as expected, and generates a

warning similar to the following at login:

WARNING: An MSM module type mismatch has been detected.

Slots MSM-A and MSM-B must both contain MSM-3's or MSM64i's.

This module type mismatch is only supported while

migrating from MSM64i's to MSM-3's.

The MSM-3 features Cross Module Trunking and Hitless Failover

will NOT operate in this configuration.

4Copy the upgraded ExtremeWare, BootROM, and configuration from the MSM64i to the MSM-3

using the synchronize command.

Upgrade Your Chassis

MSM-3 Upgrade Note 3

NOTE

An MSM-3 will not operate with ExtremeWare versions prior to 7.1.1 or BootROM versions prior to

8.1. If you inadvertantly load the wrong ExtremeWare or BootROM image, upgrade the master

MSM64i to the correct images and synchronize again.

5Force the MSM64i to fail over to the MSM-3 using the run msm-failover command.

6Remove the MSM64i that has just become the slave.

7Install another MSM-3. It initializes as the slave MSM.

8Copy the upgraded ExtremeWare, BootROM, and configuration from the master MSM-3 to the slave

MSM-3 using the synchronize command.

Verify the Installation

After you install an MSM-3, verify that it is working correctly by checking the LEDs on the front panel.

If the MSM-3 is operating normally, the front-panel LED indicators appear as follows:

•SYS LED—green blinking

•MSTR LED:

—Green: Operating as master

—Amber: Operating as slave

•ENV—green

•ERR—off

•Link/Activity:

—Green: Link is up

—Amber: Packet activity is occurring

Otros manuales para BlackDiamond 6816

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Extreme Networks

Extreme Networks

Extreme Networks Summit X150 Series Manual

Extreme Networks

Extreme Networks Summit X620-16x Manual de usuario

Extreme Networks

Extreme Networks Summit WM200 Manual de usuario

Extreme Networks

Extreme Networks Extreme Switching 3500 Series Manual de usuario

Extreme Networks

Extreme Networks Summit X48 Manual de usuario

Extreme Networks

Extreme Networks ExtremeAccess Series Manual

Extreme Networks

Extreme Networks Alpine 3804 Instrucciones de instalación

Extreme Networks

Extreme Networks Summit 200-24 Manual de usuario

Extreme Networks

Extreme Networks ExtremeSwitching X440-G2 Series Manual

Extreme Networks

Extreme Networks BlackDiamond 8800 Series Manual

Extreme Networks

Extreme Networks ExtremeSwitching VSP 7400 Series Manual

Extreme Networks

Extreme Networks Summit WM100 Manual de usuario

Extreme Networks

Extreme Networks VSP 4900 Series Manual

Extreme Networks

Extreme Networks Summit X150 Series Manual

Extreme Networks

Extreme Networks BlackDiamond 8800 Series Manual de usuario

Extreme Networks

Extreme Networks Summit X460-24t Manual de usuario

Extreme Networks

Extreme Networks ExtremeSwitching SLX 9540 Manual

Extreme Networks

Extreme Networks Summit X150 Series Manual

Extreme Networks

Extreme Networks 3626 Manual de usuario

Extreme Networks

Extreme Networks BlackDiamond 8806 Manual

Extreme Networks

Extreme Networks BlackDiamond 10808 Manual de usuario

Extreme Networks

Extreme Networks ExtremeSwitching 5520 Series Manual

Extreme Networks

Extreme Networks ExtremeSwitching 5420 Series Manual

Extreme Networks

Extreme Networks ExtremeSwitching Virtual Services Platform 4850GTS... Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario