Extech Instruments IR400 Manual de usuario

User Manual

InfraRed Thermometer

with Laser Pointer

MODEL IR400

Additional User Manual translations available at www.extech.com

IR400-en-US_v2.0 7/22

Introduction

Congratulations on your purchase of the Model IR400 IR Thermometer. The IR400 is capable of

non-contact (infrared) temperature measurements at the touch of a button. The built-in laser pointer

increases target accuracy while the backlit LCD and handy pushbuttons combine for convenient,

ergonomic operation. This meter is shipped fully tested and calibrated and, with proper use, will

provide years of reliable service.

Safety

•Use extreme caution when the laser pointer beam is on

•Do not point the beam toward anyone's eye or allow the beam

to strike the eye from a reflective surface

•Do not use the laser near explosive gases or in other

potentially explosive areas

Meter Description

1. Laser pointer beam

2. IR Sensor

3. Measurement Trigger

4. Battery Compartment

5. LCD Display

6. Pushbuttons

7. Handle Grip

Display Description

1. Temperature scan in progress (trigger held)

2. Last reading held (trigger released)

3. Laser pointer ON

4. Emissivity (0.95 fixed)

5. Max or MIN value displayed

6. Temperature display

7. Low battery icon (replace battery)

8. Temperature units

IR400-en-US_v2.0 7/22

Operating Instructions

Basic IR Measurements

1. Hold the meter by its handle and point it toward the surface to be measured.

2. Pull and hold the trigger to turn the meter on and begin testing. The temperature reading, the

flashing ‘SCAN’ icon, the unit of measure, and € = 0.95 will appear.

3. Release the Trigger and the reading will hold for approximately 10 seconds (HOLD will appear

on the LCD) after which the meter will automatically shut off.

Laser Pointer

1. When the trigger is pressed, the laser pointer will turn on and identify the spot being measured.

The icon on the display indicates that the pointer is on.

2. To turn the laser pointer off, press the button while scanning. Press the button again to

turn the pointer back on.

MAX - MIN

The Max / Min feature provides a means to display the highest (MAX) or lowest (MIN) temperature

measured during a scan.

1. While the trigger is pressed, press the MAX/MIN button. The “MAX” icon will appear and the

maximum measured temperature will appear in the display. The displayed temperature will not

change until a higher temperature is measured.

2. Press the MAX/MIN button again and the “MIN” icon will appear. The minimum temperature

only will be displayed

3. Press the MAX/MIN button again to return to a real time display.

Temperature Units C/F

To change the temperature units, press and release the trigger. Momentarily press the C/F button

and the temperature unit will change.

Backlight

When the meter is on, press the backlight button to turn the backlight on. Press the button again

to turn the backlight off.

Note: Constant use of the backlight feature will reduce battery life.

Over-Range Indication

If the temperature measurement exceeds the specified temperature range, the thermometer will

display “HI” or “LO” in place of a temperature reading.

IR400-en-US_v2.0 7/22

Field of View

The meter’s field of view is 8:1. For example, if the meter is 8 inches from the target (spot), the

diameter of the target must be at least 1 inch. Other distances are shown in the field of view

diagram. Note that measurements should normally be made as close as possible to the device

under test. The meter can measure from moderate distances, but the measurement may be affected

by external sources of light. In addition, the spot size may be so large that it encompasses surface

areas not intended to be measured.

Battery Replacement

When the battery symbol appears in the display, replace the meter’s 9V

battery. The battery compartment is located behind the panel that surrounds the

meter’s trigger. The panel can be pried open near the trigger and folded down as

shown in the diagram. Replace the 9V battery and close the battery compartment

cover.

IR400-en-US_v2.0 7/22

IR Measurement Notes

1. The object under test should be larger than the spot (target) size calculated by the field of view

diagram (printed on the side of the meter and in this guide).

2. Before measuring, be sure to clean surfaces that are covered with frost, oil, grime, etc.

3. If an object's surface is highly reflective, apply masking tape or flat black paint to the surface

before measuring. Allow time for the paint or tape to adjust to the temperature of the surface it is

covering.

4. Measurements can not be made through transparent surfaces such as glass. The surface

temperature of the glass will be measured.

5. Steam, dust, smoke, etc. can obscure measurements.

6. The meter automatically compensates for deviations in ambient temperature. However, it can

take up to 30 minutes for the meter to adjust to extremely wide changes.

7. To find a hot spot, aim the meter outside the area of interest then scan across (in an up and

down motion) until the hot spot is located.

Emissivity and IR Measurement Theory

IR Thermometers measure the surface temperature of an object. The thermometer’s optics sense

emitted, reflected, and transmitted energy. The thermometer’s electronics translate the information

into a temperature reading which is then displayed on the LCD.

The amount of IR energy emitted by an object is proportional to an object's temperature and its

ability to emit energy. This ability is known as emissivity and is based upon the material of the object

and its surface finish. Emissivity values range from 0.1 for a very reflective object to 1.00 for a flat

black finish. For the Model IR400, the emissivity is set to 0.95 which is correct for 90% of typical IR

measurement applications.

IR400-en-US_v2.0 7/22

Specifications

Display 3 ½ digit (1999 count) LCD with backlighting

Response time

Less than 1 second

Over range indication LCD will show “HI”/”LO”

Polarity Automatic (no indication for positive polarity); Minus (-) sign for negative

polarity.

Emissivity 0.95 fixed value

Field of view D/S = Approx. 8:1 ratio (D = distance, S = spot)

(90% encircled energy at the focal point)

Diode Laser Output <1mW, Wavelength 630 to 670nm, Class 2 (II) Laser product

Spectral response 6 to 14µm

Auto power off Automatic shut off after 10 seconds, approx.

Operating temperature

32oF to 122oF (0oC to 50oC)

Storage temperature

-4oF to 140oF (-20oC to 60oC)

Relative humidity 10% to 90%RH operating, <80%RH storage

Power supply 9V battery, NEDA 1604A or IEC 6LR61, or equivalent

Weight

6.3 oz (180 g)

Dimensions 3.2 x 1.6 x 6.3” (82 x 41.5 x 160mm)

Range

Resolution

Accuracy

-4F to 20°F

-20C to -7°C 0.1°F/°C ± 7.5°F (4°C)

20 to 630°F

-7C to 343°C 0.1°F/°C ± (2% of reading + 4°F [2°C])

Note: Accuracy is given at 64 °F to 82 °F (18 °C to 28 °C), less than 80%RH

IR400-en-US_v2.0 7/22

Three-year Warranty

Teledyne FLIR warrants this Extech brand instrument to be free of defects in parts and

workmanship for three years from date of shipment (a six-month limited warranty applies to sensors

and cables). To view the full warranty text please visit: http://www.extech.com/support/warranties.

Calibration and Repair Services

Teledyne FLIR offers calibration and repair services for the Extech brand products we sell. We

offer NIST traceable calibration for most of our products. Contact us for information on calibration and

repair availability, refer to the contact information below. Annual calibrations should be performed to

verify meter performance and accuracy. Product specifications are subject to change without notice.

Please visit our website for the most up-to-date product information: www.extech.com.

Contact Customer Support

Customer Support Telephone List: https://support.flir.com/contact

Calibration, Repair, and Returns: repair@extech.com

Technical Support: https://support.flir.com

www.extech.com

This document does not contain any export-controlled information

Tabla de contenidos

Otros manuales de Termómetro de Extech Instruments

Extech Instruments

Extech Instruments 42525A Manual de usuario

Extech Instruments

Extech Instruments 42500 Manual de usuario

Extech Instruments

Extech Instruments IR260 Manual de usuario

Extech Instruments

Extech Instruments TM200 Manual de usuario

Extech Instruments

Extech Instruments 445580 Manual de usuario

Extech Instruments

Extech Instruments 42311 Manual de usuario

Extech Instruments

Extech Instruments 42510A Manual de usuario

Extech Instruments

Extech Instruments EasyView 10 Manual de usuario

Extech Instruments

Extech Instruments 42570 Manual de usuario

Extech Instruments

Extech Instruments 445715-NIST Manual de usuario

Extech Instruments

Extech Instruments 421504 Manual de usuario

Extech Instruments

Extech Instruments IR250 Manual de usuario

Extech Instruments

Extech Instruments 445582 Manual de usuario

Extech Instruments

Extech Instruments 421501 Manual de usuario

Extech Instruments

Extech Instruments 39240 Manual de usuario

Extech Instruments

Extech Instruments RHT510-NIST Manual de usuario

Extech Instruments

Extech Instruments RH200W Manual de usuario

Extech Instruments

Extech Instruments EA15-NIST Manual de usuario

Extech Instruments

Extech Instruments HD200 Manual de usuario

Extech Instruments

Extech Instruments IR400 Manual de usuario

Extech Instruments

Extech Instruments 42560 Manual de usuario

Extech Instruments

Extech Instruments 445580 Manual de usuario

Extech Instruments

Extech Instruments 42570 Manual de usuario

Extech Instruments

Extech Instruments IR270 Manual de usuario

Manuales populares de Termómetro de otras marcas

Delton

Delton 981A Manual de usuario

Baker

Baker MM2P Manual de usuario

Tarmo

Tarmo 320281 Manual de usuario

Citizen

Citizen CTD 504 Manual de usuario

TFA

TFA 14.1500 Manual de usuario

Vive

Vive DMD1010 Manual de usuario

Gotemp

Gotemp THB4002 Manual de usuario

GREISINGER

GREISINGER G 1202 Manual de usuario

Amprobe

Amprobe TMD-53W Manual de usuario

Trotec

Trotec BP10 Manual de usuario

Radiance instruments

Radiance instruments RT616 Series Manual de usuario

Eurolec

Eurolec IR151 Manual de usuario

Scaneo

Scaneo TS42B Manual de usuario

Sper scientific

Sper scientific 800043 Manual de usuario

Microlife

Microlife NC 200 Manual de instrucciones

Motorola

Motorola MBP69SN Guía de configuración

The MeatStick

The MeatStick The MeatStick Manual de usuario

Hama

Hama TH35-A Manual de usuario