Extech Instruments 403265 Manual de usuario

User's Manual

Non-Contact Infrared Thermometer

Model 403265

MODE

403265 Version 1.3 Feb 2003

Introduction

Congratulations on your purchase of the Extech 403265 IR Thermometer. This

thermometer provides contact free temperature measurements with built-in laser pointer.

Careful use of this meter will provide years of reliable service.

WARNING!

The Laser button enables/disables the Laser function. When enabled, each press of

the MEAS button triggers the Laser beam. Avoid looking directly into the path of the Laser

or pointing the Laser toward anyone’s eyes. Mirrored surfaces near a measurement object

can redirect the Laser, use extreme caution. Do not allow the Laser beam to be directed

toward explosive gases.

403265 Version 1.3 Feb 2003

MODE

Meter Description

1. Infrared sensor (top)

2. Laser source (top)

3. LCD Temperature Display

4. Mode button

5. Laser pointer and Down arrow button

6. Backlight and Up arrow button

7. Measure button (MEAS)

Note: Battery compartment is on rear of meter

Specifications

General Specifications

Range/Resolution -4 to 1022oF (-20 to 550oC) / 1oF/oC

Accuracy ±2% of reading or ± 6oF/3oC (whichever is greater)

(@ 64.4 to 82.4oF (18 to 28oC) ambient temperature)

Temperature

Coefficient

A ±0.2% of reading or ±0.36oF (0.2oC) (whichever is greater)

change in accuracy per oF/oC change in ambient temperature

> 82.4oF(28oC) or < 64.4oF (18oC)

Display 3-1/2 digit (2000 count) backlit LCD with over-range and low

battery indication

Measurement rate 1 reading per second

Response time 1 second

Spectral Response 6 to 14 µm nominal

Emissivity Adjustable from 0.10 to 1.00 (in 0.01 steps)

Detection element Thermopile

Optical lens Fresnel Lens

Laser pointer Color: Red (670nm) Power: <1mW class II

Field of view D/S = Approx. 10:1 ratio (D = distance, S = spot)

Operating conditions 32 to 122oF (0 to 50oC) and < 70% relative humidity

Storage conditions -4 to 140oF (0 to 60oC) and < 80% relative humidity

Auto Power off After 20 seconds of inactivity

Standby consumption < 9mA

Power supply Four (4) 'AAA' 1.5 V batteries

Battery life 30 hours (continuous) typical with carbon-zinc battery (laser

pointer and backlight off)

Dimensions / Weight 6.7 x 1.7 x 1.6" (170 x 44 x 40mm) / 5.6 oz.(160g)

403265 Version 1.3 Feb 2003

Diameter of Spot in inches

Distance to Tar

et in inches

.1 2

Laser Beam

Sensor Beam

0.63”

0.5

Field of View

The meter’s field of view is 10:1; For example, if the meter is 10 inches from the target, the

diameter of the object under test must be at least 1 inch. The object under test should

actually be larger than the spot size shown in the diagram below. The smaller the target,

the closer the meter should be to the target. As the distance from the target increases, the

area measured by the meter (spot) becomes larger.

403265 Version 1.3 Feb 2003

Basic Operation

CAUTION!

1. Strong electromechanical radiation or static discharges can cause reading errors if

situated near the meter.

2. An explosion potential exists if the meter is exposed to corrosive or explosive gases.

3. Avoid high humidity, direct sunlight, high temperature, or condensation when

measuring.

4. Do not point the laser beam into direct sunlight or other source of strong light.

5. Do not touch the meter’s lens and do not allow the object tested to touch the lens.

6. Do not place the meter on a hot surface (> 158oF / 70oC)

7. If the meter is exposed to significant changes in ambient temperature (hot to cold or

cold to hot), allow 20 minutes for the meter to stabilize before taking measurements.

8. This unit is not dust-proof or water-proof. Use caution when using and storing the

meter.

Power ON

The meter is powered by four (4) AAA 1.5V batteries (rear battery compartment). Press

the red MEAS button to turn power on. The word “SEE” should appear followed by a

temperature reading. If not, check that the batteries are installed and fresh. The meter

does not have an OFF button, it automatically powers down after 20 seconds to preserve

battery life.

Taking Readings

There are two modes of operation, the Standard Mode and the Continuous Mode. In the

Standard Mode, the meter will measure and update the display while the MEAS button is

depressed. In the Continuous Mode, the meter will continuously measure and update the

display after the MEAS button is pressed once (auto-power off is disabled). Pressing the

MEAS button again will enable the HOLD function and the meter will turn off after 20

seconds.

Hold the MODE button down while turning power ON to toggle between the two modes.

Standard Measurement Mode

1. Point the meter toward the device under test

2. Press and hold the MEAS button and allow the reading to stabilize on the LCD display

3. Release the MEAS button. The stabilized reading will now be held on the LCD. ‘HOLD’

will appear on the LCD to indicate that the reading is being held

4. Press the MEAS button to take another measurement

5. The meter will automatically power off after 20 seconds of inactivity

Continuous Measurement Mode

1. Point the meter toward the device under test

2. Press the MEAS button to toggle between MEASURE and HOLD

3. The meter will automatically turn OFF after 20 seconds in the HOLD function, it will

remain ON in the MEASURE function.

LCD Backlight

Use the backlight button to enable or disable the LCD backlight feature. When activated,

the backlight turns on each time the MEAS button is pressed (it automatically turns off to

preserve the batteries).

403265 Version 1.3 Feb 2003

Laser Pointer

The Laser is used to help aim the IR sensor. The Laser button (center) enables the Laser

Pointer feature. When enabled, the meter emits the red laser beam each time the MEAS

button is pressed. A triangle with a black circle appears in the top left of the LCD to let the

user know that the Laser function is enabled. The triangle display icon is cleared when the

Laser feature is disabled. Note that the Laser pointer beam and the IR sensor beam are

separated by 0.63 inches (Refer to the Field of View diagram).

oC/oF Select

With the meter off, press and hold the backlight button then press the MEAS button to

select degrees F. With the meter off, press and hold the laser button then press the

MEAS button to select degrees C.

MODE Button

Pressing the MODE button while HOLD is active accesses the configuration mode. The

following parameters can be configured: Emissivity value, High Alarm setpoint (ALM Hi),

Low Alarm setpoint (ALM Lo), Maximum reading (MAX), and Minimum reading (MIN).

Emissivity Adjust

1. In the HOLD mode, press the MODE button

2. Use the UP/DOWN arrow buttons to set the desired emissivity from 0.10 to 1.00. The

normal value is 0.95.

High Alarm Set Point

1. In the HOLD mode, press the MODE button two times. “ALMHi” will appear in the

display.

2. Use the UP/DOWN arrow buttons to set the desired Hi Alarm set point.

Low Alarm Set Point

1. In the HOLD mode, press the MODE button three times. “ALM Lo” will appear in the

display.

2. Use the UP/DOWN arrow buttons to set the desired Lo Alarm set point.

MAX/MIN

1. In the HOLD mode, press the MODE button four (MAX) & five (MIN) times to view the

highest (MAX) and lowest (MIN) temperatures measured since the meter was last

turned on.

2. In the Measure mode, press the MODE button to step through the highest (MAX),

lowest (MIN) and current temperature.

403265 Version 1.3 Feb 2003

Measurement Notes

1. The object under test should be larger than the spot size calculated by the field of view

diagram (see Field of View diagram above).

2. If the surface of the object under test is covered with frost, oil, grime, etc., clean before

taking measurements.

3. If an object's surface is highly reflective apply masking tape or flat black paint before

measuring.

4. The meter cannot measure through transparent surfaces such as glass.

5. Steam, dust, smoke, etc. can obscure accurate measurements.

6. The meter compensates for deviations in ambient temperature. It can, however, take

up to 30 minutes for the meter to adjust to extremely wide temperature changes.

7. To find a hot spot, aim the meter outside the area of interest then scan across (in an up

and down motion) until the hot spot is located.

Emissivity Note

Most organic materials and painted or oxidized surfaces have an emissivity factor of 0.95.

Inaccurate readings will result from measuring shiny or polished metal surfaces which have

emissivity factors other than 0.95. To compensate for polished/shiny surfaces, cover the

surface with masking tape or flat black paint. Allow time, before measuring, for the tape to

reach the same temperature as the material underneath it.

Emissivity Factors for Common Materials

Material under test Emissivity Material under test Emissivity

Asphalt 0.90 to 0.98 Cloth (black) 0.98

Concrete 0.94 Skin (human) 0.98

Cement 0.96 Lather 0.75 to 0.80

Sand 0.90 Charcoal (powder) 0.96

Soil 0.92 to 0.96 Lacquer 0.80 to 0.95

Water 0.92 to 0.96 Lacquer (matt) 0.97

Ice 0.96 to 0.98 Rubber (black) 0.94

Snow 0.83 Plastic 0.85 to 0.95

Glass 0.90 to 0.95 Timber 0.90

Ceramic 0.90 to 0.94 Paper 0.70 to 0.94

Marble 0.94 Chromium Oxides 0.81

Plaster 0.80 to 0.90 Copper Oxides 0.78

Mortar 0.89 to 0.91 Iron Oxides 0.78 to 0.82

Brick 0.93 to 0.96 Textiles 0.90

403265 Version 1.3 Feb 2003



Support Hotline (781) 890-7440

Tech support: Ext. 200; Email: [email protected]

Repair/Returns: Ext. 210; Email: [email protected]

Website: www.extech.com

Battery Replacement

When the low battery symbol appears on the LCD, replace the meter’s four (4) AAA

1.5V batteries. The battery compartment is located on the rear of the meter. Open the

compartment by removing the screw and sliding the battery compartment cover off in the

direction of the arrow. Replace batteries observing polarity and re-install the battery

compartment cover.

Warranty

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and

workmanship for one year from date of shipment (a six month limited warranty applies on sensors and

cables). If it should become necessary to return the instrument for service during or beyond the warranty

period, contact the Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our

website at www.extech.com (click on ‘Contact Extech’ and go to ‘Service Department’ to request an RA

number). A Return Authorization (RA) number must be issued before any product is returned to Extech. The

sender is responsible for shipping charges, freight, insurance and proper packaging to prevent damage in

transit. This warranty does not apply to defects resulting from action of the user such as misuse, improper

wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification.

Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and

will not be liable for any direct, indirect, incidental or consequential damages. Extech's total liability is limited

to repair or replacement of the product. The warranty set forth above is inclusive and no other warranty,

whether written or oral, is expressed or implied.

Calibration and Repair Services

Extech offers complete repair and calibration services for all of the products we sell.

For periodic calibration, NIST certification or repair of any Extech product, call customer

service for details on services available. Extech recommends that calibration be performed

on an annual basis to ensure calibration integrity.

Tabla de contenidos

Otros manuales de Termómetro de Extech Instruments

Extech Instruments

Extech Instruments SL250W Manual de usuario

Extech Instruments

Extech Instruments RH210 Manual de usuario

Extech Instruments

Extech Instruments 401014A Manual de usuario

Extech Instruments

Extech Instruments TM55 Manual de usuario

Extech Instruments

Extech Instruments 392050 Manual de usuario

Extech Instruments

Extech Instruments TM100 Manual de usuario

Extech Instruments

Extech Instruments 42540 Manual de usuario

Extech Instruments

Extech Instruments RH490 Manual de usuario

Extech Instruments

Extech Instruments IR320 Manual de usuario

Extech Instruments

Extech Instruments 42512 Manual de usuario

Extech Instruments

Extech Instruments 407445 Manual de usuario

Extech Instruments

Extech Instruments EasyView EA20 Manual de usuario

Extech Instruments

Extech Instruments 445715 Manual de usuario

Extech Instruments

Extech Instruments RH250W Manual de usuario

Extech Instruments

Extech Instruments IRC130 Manual de usuario

Extech Instruments

Extech Instruments TM300 Manual de usuario

Extech Instruments

Extech Instruments RHM15 Manual de usuario

Extech Instruments

Extech Instruments RHT510 Manual de usuario

Extech Instruments

Extech Instruments IR300UV Manual de usuario

Extech Instruments

Extech Instruments MO295 Manual de usuario

Extech Instruments

Extech Instruments RH490 Manual de usuario

Extech Instruments

Extech Instruments TM200 Manual de usuario

Extech Instruments

Extech Instruments 42540A Manual de usuario

Extech Instruments

Extech Instruments EA10-NIST Manual de usuario

Manuales populares de Termómetro de otras marcas

Delton

Delton 981A Manual de usuario

Baker

Baker MM2P Manual de usuario

Tarmo

Tarmo 320281 Manual de usuario

Citizen

Citizen CTD 504 Manual de usuario

TFA

TFA 14.1500 Manual de usuario

Vive

Vive DMD1010 Manual de usuario

Gotemp

Gotemp THB4002 Manual de usuario

GREISINGER

GREISINGER G 1202 Manual de usuario

Amprobe

Amprobe TMD-53W Manual de usuario

Trotec

Trotec BP10 Manual de usuario

Radiance instruments

Radiance instruments RT616 Series Manual de usuario

Eurolec

Eurolec IR151 Manual de usuario

Scaneo

Scaneo TS42B Manual de usuario

Sper scientific

Sper scientific 800043 Manual de usuario

Microlife

Microlife NC 200 Manual de instrucciones

Motorola

Motorola MBP69SN Guía de configuración

The MeatStick

The MeatStick The MeatStick Manual de usuario

Hama

Hama TH35-A Manual de usuario