Extech Instruments SDL550 Manual de usuario

User's Guide

Moisture Content Meter

Plus Dew Point, Wet Bulb, and Thermocouple Temperature functions

SD Card real-time datalogger

Model SDL550

%RH

Moisture Content

Meter

SDL550

SDL550-EU-EN-V1.2-10/11

%RH

1 2

Moisture Content

Meter

SDL550

Introduction

Congratulations on your purchase of the Extech SDL550 Moisture Content Meter. This meter

displays and stores Moisture Content readings, Air Temperature, Dew Point Temperature, and Wet

Bulb Temperature. Logged data readings are stored on an SD card for transfer to a PC. In addition,

an RS232 port allows data streaming to a PC. This meter is shipped fully tested and calibrated and,

with proper use, will provide years of reliable service.

Safety

International Safety Symbols

This symbol, adjacent to another symbol or terminal, indicates the user must refer to the

manual for further information.

Meter Description

1. Thermocouple Temperature Probe input jack

2. Moisture Sensor input jack

3. Primary LCD Display digits

4. Unit of Measure for Primary Display

5. HOLD and Backlight key

6. MAX-MIN key

7. SET and Clock key

8. PC interface jack

9. Reset button

10. Power Adaptor jack

11. SD card slot

12. ENTER and LOG key

13. Down arrow ▼/ FUNCTION key

14. Up arrow ▲key

15. Power ON-OFF key

16. Secondary LCD Display digits with unit of measure

Notes: Items 8, 9, and 10 are located behind the snap-off compartment cover on meter’s right side.

Battery compartment, tilt stand, and tripod mount are locatedon the rearof the instrument

SDL550-EU-EN-V1.2-10/11

Moisture Probe Description

1. Probe Handle

2. Probe connecting cable

3. Probe-to-meter input plug

4. Probe collar

(probe sensor unscrews from here to access filter)

5. Moisture Sensor penetrating tip

6. Sensor port openings

7. Protective cap

(slides off of sensor tip)

Basic Operation

Power ON-OFF

•Power the meter by pressing and holding the power button for at least 1.5 seconds.

•Press and hold the power button for at least 1.5 seconds to power OFF the meter.

•This meter is powered by six (6) 1.5VDC ‘AA’ batteries or by optional AC adaptor.

Display Backlight

To turn the display backlight ON or OFF, press and hold the backlight button for at least 1.5

seconds. The meter will beep when switching the backlight ON or OFF unless the beeper is

disabled.

Moisture Content Sensor

The supplied Moisture Content sensor connects to the meter via the DIN jack at the top right of the

meter. Note that the utility end of the sensor is located beneath the protective cap; use great caution

when removing the cap and when handling the sensor as the sensor head is extremely sharp. The

sensor uses an internal filter and when the filter becomes soiled or defective the readings take

longer to stabilize. Contact Extech for replacement filters.

Temperature (Thermocouple) Sensor

A type J or K thermocouple (optional) can be connected to the meter via the thermocouple input

jack at the top left of the meter for measuring air temperature. Note that the temperature range of

the meter extends up to 1300

C (2372

F), however thermocouple ranges vary greatly; be sure to

select a thermocouple rated for the expected temperature measurement ranges.

SDL550-EU-EN-V1.2-10/11

Selecting Meter Functions

The SDL550 can measure Moisture Content (%RH), Dew Point Temperature (

F), Wet Bulb

Temperature (

F), and Thermocouple Temperature (

F). Press and hold the FUNCTION button

for 1.5 seconds to begin scrolling through the functions. Release the FUNCTION button when the

desired function is displayed. Refer to the table below.

Functions Primary display Secondary display Unit of measure

Moisture Content Relative Humidity rh briefly displayed then the

Moisture Probe Temperature RH% and

C or

Dew Point Temperature* dp display icon

C or

Wet Bulb Temperature* _et display icon

C or

Air Temperature Thermocouple Temperature tp briefly displayed

C or

Measurements

Moisture Content Measurements

1. Connect the Moisture probe to the jack at the top of the meter on the right

2. Switch the meter ON by pressing and holding the power button for 1.5 seconds

3. Press and hold the FUNCTION button to select the Moisture Content mode. When the Moisture

Content mode is selected, the display icon rh is briefly shown

4. Carefully remove the protective cap from the moisture probe. The probe tip is extremely sharp,

use caution

5. Insert the probe tip into the material under test far enough to cover the sensor’s openings

6. The meter will now display moisture content in %RH on the primary (upper) LCD digits

7. The secondary (lower) LCD digits will show the temperature measured by the moisture probe’s

built-in temperature sensor. Use the Setup mode to change the temperature units of measure

8. Note that the probe uses a built-in filter. When the filter needs replacing (becomes soiled or

defective), the measurement readings require a longer stabilization time. Please contact Extech

for replacement filters

Dew Point and Wet Bulb Temperature Measurements

1. Connect the Moisture probe to the jack at the top of the meter on the right

2. Switch the meter ON by pressing and holding the power button for 1.5 seconds

3. Press and hold the FUNCTION button to select the Wet Bulb or the Dew Point mode. When the

Dew Point mode is selected, the display icon dp is shown on the secondary display area. When

the Wet Bulb mode is selected, the display icon _et is shown on the secondary display area.

4. Carefully remove the protective cap from the moisture probe. The probe tip is extremely sharp,

use caution

5. Insert the probe tip into the material under test far enough to cover the sensor’s openings

6. The meter will now display the Dew Point Temperature or Wet Bulb Temperature on the primary

(upper) LCD digits. Use the Setup mode to change the temperature units of measure

SDL550-EU-EN-V1.2-10/11

Thermocouple Temperature Measurements

1. Note that the temperature range of the meter extends up to 1300

C (2372

F), however

thermocouple sensor ranges vary greatly; be sure to select a thermocouple rated for the

expected temperature measurement ranges.

2. Connect a Thermocouple Temperature sensor (not supplied) to the jack at the top of the meter

on the left

3. Switch the meter ON by pressing and holding the power button for 1.5 seconds

4. Press and hold the FUNCTION button to select the Thermocouple Temperature mode. When

the Thermocouple Temperature mode is selected, the display icon tp is briefly shown. The

thermocouple type (J or K) will be shown on the left side of the LCD. Use the Setup mode to

change the thermocouple type

5. Hold the thermocouple sensor tip in the air to be measured

6. The meter will now display thermocouple temperature on the primary (upper) LCD digits. Use

the Setup mode to change the temperature units of measure

Data Hold

To freeze a displayed reading on the LCD, momentarily press the HOLD button (the HOLD icon will

appear above the reading). To exit the Data Hold mode, press the HOLD button again.

Max-Min Reading Record

For a given measurement session, this meter can record the highest (MAX) and the lowest (MIN)

readings for later recall.

1. Press the MAX-MIN button momentarily to access this mode of operation (REC icon appears)

2. The meter is now recording the MAX and MIN readings.

3. Press the MAX-MIN button again to view the current MAX readings (MAX icon appears). The

readings on the display are now the highest readings encountered since the REC icon was

switched on (when the MAX-MIN button was first pressed).

4. Press the MAX-MIN button again to view the current MIN readings (MIN icon appears). The

readings on the display are now the lowest readings encountered since the REC icon was

switched on (when the MAX-MIN button was first pressed).

5. To exit the MAX-MIN mode, press and hold the MAX-MIN button for at least 1.5 seconds. The

meter will beep, the REC-MAX-MIN icons will switch off, the MAX-MIN memory will clear, and

the meter will return to the normal operating mode.

SDL550-EU-EN-V1.2-10/11

Setup Mode

Basic settings at a glance

To view the current configuration of the meter with regard to time, date, and datalogging sampling

rate press the SET button momentarily. The meter will now display the configuration in quick

succession. If the information is missed on the first try, simply press the SET button again until all of

the information is noted.

Accessing the Setup mode

1. Press and hold the SET button for at least 1.5 seconds to access the Setup menu.

2. Press the SET button momentarily to step through the available parameters. The parameter

type is shown on the bottom of the LCD and the current selection for that type is shown above it.

3. When a parameter is displayed that is to be changed, use the arrow keys to change the setting.

Press the ENTER button to confirm a change.

4. Press and hold the SET button for at least 1.5 seconds to exit the Setup mode. Note that the

meter automatically switches out of the Setup mode if no key is pressed within 7 seconds.

The available Setup parameters are listed below. Additional detailed information is provided

below this list:

dAtE

Set the clock (Year/Month/Date; Hours/Minutes/Seconds)

SP-t

Set the datalogger sampling rate (0 to 3600 Seconds)

PoFF

Automatic power-off management (Enable or disable the auto-power off function)

bEEP

Set the beeper sound ON/OFF

dEC

Set the numerical format; USA (decimal: 20.00) or European (comma: 20,00)

SdF

Format the SD memory card

t-CF

Select the temperature unit of measure (degrees C orF)

tYPE

Select the thermocouple type (J or K)

Setting the Clock Time

1. Access the dAtE parameter.

2. Use the arrow keys to change a value

3. Use the ENTER button to step through the selections

4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or

simply wait 7 seconds for the meter to automatically switch to the normal operating mode).

5. The clock will keep accurate time even when the meter is switched off. However, if the battery

expires the clock will have to be reset after fresh batteries are installed.

SDL550-EU-EN-V1.2-10/11

Setting the Datalogger Sampling Time (Rate)

1. Access the SP-t parameter.

2. Use the arrow buttons to select the desired sampling rate. The available settings are: 0, 1, 2, 5,

10, 30, 60, 120, 300, 600, 1800, and 3600 seconds.

Pressthe ENTERbuttontoconfirmtheentry.

4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode.

Enabling/Disabling the Auto Power OFF Feature

1. Access the PoFF parameter.

2. Use the arrow buttons to select ON or OFF. With the Auto Power OFF feature enabled, the

meter will automatically switch OFF after 10 minutes of inactivity.

3. Press ENTER to confirm setting.

4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode.

Set the Beeper Sound ON or OFF

1. Access the bEEP parameter.

2. Use the arrow buttons to select ON or OFF.

3. Press ENTER to confirm setting.

4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode.

Numerical Format (comma or decimal)

European and USA numerical formats differ. The meter defaults to USA mode where a decimal

point is used to separate units from tenths, i.e. 20.00; The European format uses a comma, i.e.

20,00 to separate units from tenths. To change this setting:

1. Access the dEC parameter.

2. Use the arrow buttons to select USA or EUro.

3. Press ENTER to confirm setting.

4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode.

SD Card FORMATTING

1. Access the Sd-F parameter.

2. Use the arrow buttons to select YES to format the card (select NO to abort). Note that all data

on the card will be lost if formatting is attempted.

3. Press ENTER to confirm selection.

4. Press ENTER again to re-confirm.

5. The meter will automatically return to the normal operating mode when formatting is complete.

If not, press and hold SET button for at least 1.5 seconds to exit to the normal operation mode.

Set the Temperature Units of Measure (°C or °F)

1. Access the t-CF parameter.

2. Use the arrow buttons to select °C or °F. Press ENTER to confirm setting.

3. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode.

SDL550-EU-EN-V1.2-10/11

Set the Thermocouple Type

1. Access the tYPE parameter.

2. Use the arrow buttons to select the desired sensor type (Jor K)

3. Press ENTER to confirm setting.

4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or

simply wait 7 seconds for the meter to automatically switch to the normal operating mode).

Datalogging

Types of Data Recording

•Manual Datalogging: Manually log up to 99 readings onto an SD card via push-button press.

•Automatic Datalogging: Automatically log data onto an SD memory card where the number of

data points is limited only by the card size. Readings are logged at a rate specified by the user.

SD Card Information

•Insert an SD card (from 1G size up to 16G) into the SD card slot at the bottom of the meter. The

card must be inserted with the front of the card (label side) facing toward the rear of the meter.

•If the SD card is being used for the first time it is recommended that the card be formatted and

the logger’s clock set to allow for accurate date/time stamping during datalogging sessions.

Refer to the Setup Mode section for SD card formatting and time/date setting instructions.

•European and USA numerical formats differ. The data on the SD card can be formatted for

either format. The meter defaults to USA mode where a decimal point is used to separate units

from tenths, i.e. 20.00. The European format uses a comma, i.e. 20,00. To change this setting,

refer to the Setup Mode section.

Manual Datalogging

In the manual mode the user presses the LOG button to manually log a reading onto the SD card.

1. Set the sampling rate to ‘0’ seconds as described in the Setup Mode section.

2. Press and hold the LOG button for at least 1.5 seconds and the secondary display area will

show p-n(n= memory position number 1-99).

3. Momentarily press the LOG button to store a reading. The REC icon will flash each time a data

point is stored.

4. Use the ▲and ▼buttons to select one of the 99 data memory positions in which to record.

5. To exit the manual datalogging mode, press and hold the LOG button for at least 1.5 seconds.

SDL550-EU-EN-V1.2-10/11

Automatic Datalogging

In automatic datalogging mode the meter takes and stores a reading at a user-specified sampling

rate onto an SD memory card. The meter defaults to a sampling rate of two seconds. To change the

sampling rate, refer to the Setup Mode section (the sampling rate cannot be ‘0’ for automatic

datalogging):

1. Select the sampling rate in the Setup Mode to a value other than zero.

2. Press and hold the LOG button for at least 1.5 seconds. The meter will flash the REC icon at the

selected sampling rate indicating that readings are now being automatically recorded to the SD

card. The LOG display icon will appear on the secondary (lower) LCD display digits.

3. If a card is not inserted, the meter will display "Sd","-E-" If a card is defective, the meter will

display " ScAn "," Sd ".

4. Pause the datalogger by pressing the LOG button momentarily. The REC icon will stop flashing

and the sample rate will display for a short time. To resume logging simply press the LOG

button again momentarily.

5. To terminate the datalogging session press and hold the LOG button for at least 1.5 seconds.

6. When an SD card is used for the first time a folder is created on the card and named HTB01. Up

to 99 spreadsheet documents (each with 30,000 readings) can be stored in this folder.

7. When datalogging begins a new spreadsheet document named HTB01001.xls is created on the

SD card in the HTB01 folder. The data recorded will be placed in the HTB01001.xls document

until 30,000 readings are reached.

8. If the measurement session exceeds 30,000 readings, a new document will be created

(HTB01002.xls) where another 30,000 readings can be stored. This method continues for up to

99 documents, after which another folder is created (HTB02) where another 99 spreadsheet

documents can be stored. This process continues in this same fashion with folders HTB03

through HTB10 (last allowable folder).

SD Data Card to PC Data Transfer

1. Complete a datalogging session as detailed in above in the previous sections. Hint: For the first

few tests, simply record a small amount of test data. This is to ensure that the datalogging

process is well understood before committing to critical, large scale datalogging.

2. With the meter switched OFF, remove the SD Card.

3. Plug the SD Card directly into a PC SD card reader. If the PC does not have an SD card slot,

use an SD card adaptor (available at most outlets where computer accessories are sold).

4. Power the PC and run a spreadsheet software program. Open the saved documents in the

spreadsheet software program (see example spreadsheet data screen below).

Spreadsheet data example

SDL550-EU-EN-V1.2-10/11

RS-232/USB PC Interface

The optional 407001A software kit (software and cable) allows streaming of data to a PC via

the RS232 Output jack.

AC Power Adaptor

This meter is normally powered by six (6) 1.5V ‘AA’ batteries. An optional 9V power adaptor is

available. When the adaptor is used, the meter is permanently powered and the power button will

be disabled.

System Reset

If the meter’s keys become inoperable or if the display freezes the Reset button can be used to

reset the instrument.

1. Use a paper clip or similar item to momentarily press the reset button located on the lower right

side of the instrument under the snap-off compartment cover.

2. After pressing the Reset button, switch the instrument ON by pressing and holding the POWER

key for at least 1.5 seconds. If using the power adaptor unplug the adaptor and then plug it back

in again to power the meter.

Battery Replacement and Disposal

When the low battery icon appears on the LCD, the batteries must be replaced. Several hours of

accurate readings are still possible in this condition; however batteries should be replaced as soon

as possible:

1. Remove the two (2) Phillips screws from the rear of the meter (directly above the top of the tilt

stand).

2. Remove and safely place the battery compartment and screws where they will not be damaged

or lost.

3. Replace the six (6) 1.5V ‘AA’ batteries observing polarity.

4. Replace the battery compartment cover with the two (2) Phillips screws.

All EU users are legally bound by the battery ordinance to return all used batteries to

collection points in your community or wherever batteries / accumulators are sold!

Disposal in the household garbage is prohibited!

Tabla de contenidos

Otros manuales de Instrumento de medición de Extech Instruments

Extech Instruments

Extech Instruments 380973 Manual de usuario

Extech Instruments

Extech Instruments MO220 Manual de usuario

Extech Instruments

Extech Instruments 407510 Manual de usuario

Extech Instruments

Extech Instruments CO10 Manual de usuario

Extech Instruments

Extech Instruments 341350A Manual de usuario

Extech Instruments

Extech Instruments EC210 Manual de usuario

Extech Instruments

Extech Instruments 400790A Manual de usuario

Extech Instruments

Extech Instruments MO500 Manual de usuario

Extech Instruments

Extech Instruments 480823 Manual de usuario

Extech Instruments

Extech Instruments 380803 Manual de usuario

Extech Instruments

Extech Instruments 380460 Manual de usuario

Extech Instruments

Extech Instruments 407355 Manual de usuario

Extech Instruments

Extech Instruments 380940 Manual de usuario

Extech Instruments

Extech Instruments MA145 Manual de usuario

Extech Instruments

Extech Instruments EMF450 Manual de usuario

Extech Instruments

Extech Instruments SDL310 Manual de usuario

Extech Instruments

Extech Instruments MA160 Manual de usuario

Extech Instruments

Extech Instruments 380460 Manual de usuario

Extech Instruments

Extech Instruments LT250W Manual de usuario

Extech Instruments

Extech Instruments MO53 Manual de usuario

Extech Instruments

Extech Instruments HD755 Manual de usuario

Extech Instruments

Extech Instruments 407703A Manual de usuario

Extech Instruments

Extech Instruments EX613 Manual de usuario

Extech Instruments

Extech Instruments RH390 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario