Extech Instruments MO210 Manual de usuario

USERGUIDE

Moisture Meter

Model MO210

MO210-en-GB_V2.4 7/15

Introduction

Thank you for selecting the Extech Model MO210. This device is shipped fully tested and calibrated

and, with proper use, will provide years of reliable service. Please visit our website (www.extech.com)

to check for the latest version of this User Guide, Product Updates, and Customer Support.

Cautions

The electrode measurement pins are extremely sharp. Use care when handling this instrument.

Cover the pins with the protective cap when the instrument is not in use

This device is not a toy and must not reach children’s hands. It contains hazardous objects as well

as small parts that the children could swallow. In case a child swallows any of them, please

contact a physician immediately

Do not leave the battery and packing material lying around unattended; they can be dangerous for

children if they use them as toys

In case the device is going to be unused for an extended period of time, remove the battery to

prevent them from draining

Expired or damaged batteries can cause cauterization on contact with the skin. Always, therefore,

use suitable hand gloves in such cases

See that the battery is not short-circuited. Do not throw the battery into a fire

MO210-en-GB_V2.4 7/15

Description

Meter Description

1. Measurement electrode pin

2. Cutoff switch

3. LCD (detail below)

4. Hand grip

5. Verification Test Points

6. Battery check Test Points

7. Removable cap

8. Material Selector Switch

Display Description

1. Graphical Display

2. Numerical Reading

3. Units

4. Low Battery Indicator

5. Solid lines – even number

6. Dashed lines – odd number

Wood Scale Building Material

Scale

MO210-en-GB_V2.4 7/15

Operation

1. Remove the protective cap to expose the electrode pins.

2. The meter automatically switches ON when the cap is removed.

3. The meter automatically shuts OFF when the cap is replaced.

4. To conserve battery life, the meter automatically shuts off after 15 minutes when the cap is

left off. To revive the meter after an Auto Power OFF, simply press the yellow cut-off switch

momentarily.

5. Slide material selection switch to read wood moisture or building moisture.

6. Carefully push the electrode pins as far as possible into the material under test. Note that

the pins should be inserted into wood perpendicular to the wood’s fiber structure.

7. Take several readings in several locations on the material for the best representation of the

amount of moisture present.

8. Read the measurement values on the display.

9. Replace the protective cap when finished.

Reading the Display

1. The LCD display has two scales

2. The wood scale indicates wood moisture from 6 to 44%.

3. The building materials scale indicates moisture content

from 0.2 to 2.4%. To calculate the Wood % equivalent

multiple the building material reading by 20.

(example – 0.6% building x 20 = 12 %WME).

4. A continuous line indicates an even number. A dotted line

indicates on odd number.

5. The battery icon appears when the batteries are weak and

require replacement.

Auto Power OFF

With the protective cap removed, the meter will turn off after 15

minutes to conserve battery life. Press the yellow cutoff switch

momentarily to restart the meter. Always secure the protective

cap when the instrument is not in use.

Instrument Measurement Verification check

1. With the meter wood moisture position, touch the electrode test pins to the two test points 1

and 2 at the top of the protective cap labeled ‘T’.

2. With the unit on and the electrode pins touching the ‘T’ test points, the meter should read

27% ±2%. If not, the meter may require repair.

Battery Check

1. With the meter wood moisture position, touch the electrode test pins

to the two test points 3 and 4 at the top of the protective cap labeled

‘B’ (see diagram).

2. With the unit on and the electrode pins touching the ‘B’ test points, the meter should read >

44%±2% on the wood moisture scale. If not, replace the batteries.

CAUTION: The electrode measurement pins are extremely sharp. Use

care when handling this instrument. Cover the pins with the protective cap

when the instrument is not in use.

Wood Scale Building Material

Scale

MO210-en-GB_V2.4 7/15

Battery Replacement

If the instrument does not switch on, displays the low battery symbol, or if the Battery Check yields

less than 44% on the wood moisture scale, replace the batteries as follows:

1. Remove the Phillips head screw from the belt clip/battery compartment located on the

rear of the instrument.

2. Remove the batteries taking note of their orientation and polarity.

3. Install three (3) new CR-2032 button batteries observing polarity.

4. Secure the battery compartment with the Phillips head screw.

You, as the end user, are legally bound (EU Battery ordinance) to return all used

batteries, disposal in the household garbage is prohibited! You can hand over your

used batteries / accumulators at collection points in your community or wherever batteries

/ accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle.

Battery Safety Reminders

Please dispose of batteries responsibly; always observe local, state, and federal regulations

with regard to battery disposal.

Never dispose of batteries in a fire. Batteries may explode or leak.

Never mix battery types. Always install new batteries of the same type.

Electrode Pin Replacement

To replace the two electrode pins:

1. Remove the protective cap

2. Unscrew the electrode pins

3. Install the new pins

4. Replace the protective cap

Maintenance

Always keep the instrument dry

Prevent dirt from accumulating at the electrode pins

MO210-en-GB_V2.4 7/15

Specifications

Display Dual measurement scale LCD with bargraph metering

Measurement principle Electrical resistance

Range Wood: 6 to 44%, Building materials: 0.2 to 2.4%

Electrode length 9.5mm (0.375”)

Electrode pins Integrated, replaceable

Auto Power OFF After approx. 15 minutes

Power supply Three (3) CR-2032 button cells

Meter housing Impact-proof plastic

Operating Temperature 0 to 40oC (32 to 104oF)

Operating Humidity 85% Relative Humidity maximum

Dimensions 130 x 40 x 25mm (5.1 x 1.6 x 1.0”)

Weight 108.3g. (3.82 oz)

Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform

ISO-9001 Certified

www.extech.com

Tabla de contenidos

Otros manuales de Instrumento de medición de Extech Instruments

Extech Instruments

Extech Instruments 461891 Manual de usuario

Extech Instruments

Extech Instruments EA30 Manual de usuario

Extech Instruments

Extech Instruments SDL800 Manual de usuario

Extech Instruments

Extech Instruments CO80 Manual de usuario

Extech Instruments

Extech Instruments TKG100 Manual de usuario

Extech Instruments

Extech Instruments RF153 Manual de usuario

Extech Instruments

Extech Instruments ExStik EC510 Manual de usuario

Extech Instruments

Extech Instruments 451181 Manual de usuario

Extech Instruments

Extech Instruments MA430T Manual de usuario

Extech Instruments

Extech Instruments MO297 Manual de usuario

Extech Instruments

Extech Instruments DT500 Manual de usuario

Extech Instruments

Extech Instruments 380363 Manual de usuario

Extech Instruments

Extech Instruments SDL470-NISTL Manual de usuario

Extech Instruments

Extech Instruments DT200 Manual de usuario

Extech Instruments

Extech Instruments ExStik RE300 Manual de usuario

Extech Instruments

Extech Instruments 451104 Manual de usuario

Extech Instruments

Extech Instruments UV505 Manual de usuario

Extech Instruments

Extech Instruments MO57 Manual de usuario

Extech Instruments

Extech Instruments 407727 Manual de usuario

Extech Instruments

Extech Instruments 433201A Manual de usuario

Extech Instruments

Extech Instruments PH220 Manual de usuario

Extech Instruments

Extech Instruments VB450 Manual de usuario

Extech Instruments

Extech Instruments 407703A Manual de usuario

Extech Instruments

Extech Instruments 380801 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario