Explore Scientific RDP3007 Manual de usuario

EN INSTRUCTION MANUAL...............2

IT ISTRUZIONI PER L’USO.............. 14

DE BEDIENUNGSANLEITUNG .......... 28

FR MODE D‘EMPLOI....................... 42

ES MANUAL DE INSTRUCCIONES.... 56

*Radio-controlled clock function not available in all territories. / Funzione di orologio radiocontrollati non disponibile in ogni territorio. / Funkuhrfunktion nicht in jederm Gebiet verfügbar. / La fonction

d‘horloge radio-piloté n‘est pas disponible dans tous les territoires. / La función de reloj radiocontrolado no está disponible en todos los territorios.

RADIO-CONTROLLED* PROJECTION CLOCK

SVEGLIA RADIOCONTROLLATA*CON PROIETTORE

PROJEKTIONS-FUNKWECKER*

PROJECTION RÉVEIL RADIO-COMMANDÉ*

PROYECCIÓN RELOJ DESPERTADOR RADIO-

CONTROLADO*

Art.No.: RDP3007

ABOUT THIS INSTRUCTION

MANUAL

These operating instructions are to be considered

a component of the device.

Please read the safety instructions and the operating

instructions carefully before use.

Keep these instructions for renewed use at a later date.

When the device is sold or given to someone else, the

instruction manual must be provided to the new owner/

user of the product. The device is intended only for

indoor use.

GENERAL WARNINGS

•Risk of electric shock — This device contains

electronic components that operate via a

power source (power supply and/or batteries).

Children should only use the device under adult

supervision. Only use the device as described

in the manual; otherwise, you run the risk of an

electric shock.

• Choking hazard —Children should only use the

device under adult supervision. Keep packaging

material, like plastic bags and rubber bands, out

of the reach of children, as these materials pose a

choking hazard.

• Risk of chemical burn —Keep batteries out of

the reach of children! Make sure you insert the

batteries correctly. Leaking battery acid can lead to

chemical burns. Avoid contact of battery acid with

skin, eyes and mucous membranes. In the event of

contact, rinse the affected region immediately with

a plenty of water and seek medical attention.

• Risk of re/explosion —Do not expose the device

to high temperatures. Use only the recommended

batteries. Do not short-circuit the device or

batteries, or throw them into a re. Excessive heat

or improper handling could trigger a short-circuit,

a re, or an explosion.

• Do not disassemble the device. In the event of a

defect, please contact your dealer. The dealer will

contact the Service Centre and can send the device

in to be repaired, if necessary.

• Use only the recommended batteries. Always

replace weak or empty batteries with a new,

complete set of batteries at full capacity. Do not

use batteries from different brands or with different

capacities. The batteries should be removed from

the unit if it has not been used for a long time.

SCOPE OF DELIVERY

Alarm clock, Power adapter, Operating instructions,

2x AAA batteries

BEFORE YOU BEGIN

• We recommend using alkaline batteries. If

temperatures regularly fall below 0°C (32°F), we

recommend using lithium batteries.

• Avoid using rechargeable batteries. (Rechargeable

batteries cannot maintain correct power

requirements.)

• Insert batteries before rst use, matching the

polarity in the battery compartment. 2x AAA

Batteries are required.

PRODUCT OVERVIEW

1. Press [ ] to activate the snooze

function and backlight for 8 seconds. The

Snooze function will stop the alarm for 8

minutes. Press [ ] to flip the

projection by 180°. Press and hold to turn

on backlight for 8 seconds and projection

for 5 minutes. Press and hold again, to turn

on backlight for 8 seconds and continuous

projection. (Continous projection only with

AC/DC Adpater).

2. Projection lens.

3. Press [ ] to turn on/off alarm.

4. Press [ ] to toggle between the calendar

and alarm display. Press and hold to enter the

alarm setting mode.

5. Press and hold [ ] to enter time and date

setting mode.

6. Press and hold [ ] to turn RCC on/off. In

setting mode, press to increase one unit, press

and hold to increase rapidly.

 

    

7. Press and hold [ ] to display the temperature or

time (only when the projection is on). In setting

mode, press to decrease one unit, press and hold

to decrease rapidly.

8. Adjust projection focus with the focus wheel.

9. Press the RESET button to restore settings to

factory default.

10. Battery compartment. Slide down to open.

11. Power jack.





 

MODE BUTTON

Standard

mode

PRESS

Turn on backlight

for 8 seconds

(SNOOZE when

alarm is ringing)

Projection 180°

switch

Turn Alarm

on/off

Stop alarm

(ringing)

Toggle between

Calendar and Alarm

display

_______ _______ _______

HOLD

Turn on backlight

for 8 seconds

and projection

for 5 minutes.

Hold again to

activate continous

projection (only with

AC/DC Adapter)

_______ Enter into

alarm setting

Enter into

time and date

setting

Turn RCC

on/off

Display

Temperature or

Time (only when

the projection

is on)

Time

setting

mode

PRESS _______ _______ Conrm

setting Conrm setting Increase Decrease

HOLD _______ _______ _______ _______ Quick

Increase Quick Decrease

Alarm

setting

mode

PRESS _______ _______ _______ Conrm setting Increase Decrease

HOLD _______ _______ _______ _______ Quick

Increase Quick Decrease

LCD DISPLAY

1. Time display

2. Calendar display

3. Weekday display

4. Temperature display

[ ] RCC signal received

[ ] Time Zone indicator

[ ] Snooze activated

[ ] Alarm 1 ON

[ ] Alarm 2 ON

[ ] Alarm 1 + Alarm 2 ON

[ ] Low battery indicator



  

GETTING STARTED

INSERT BATTERIES

1. Remove the battery door from the back.

2. Insert 2x AAA (LR03)/1.5V batteries. Please ensure

the polarities (+/-) of the batteries match upon

installation.

3. Reattach the battery door.

NOTE: Replace batteries when [ ] displays, or

when the display is dim.

AC/DC POWER ADAPTER

Only use a compatible AC/DC Power adapter (3.6V

100mA). Plug the power cable to the power jack

and the power adapter to a suitable power outlet.

NOTE: We recommend to insert batteries as backup

power source.

CLOCK

CLOCK RECEPTION

1.Replace batteries or press and hold [ ] button will

initiate RCC receiving.

2.The receiving process duration is 7 minutes.

3.During receiving process, the RCC signal symbol

[ ] flashes.

4. If the RCC receiving process is successful, a

completed RCC symbol [ ] will be shown

in the display and the date and time will be set

automatically. If it fails within 7 minutes, RCC setting

will quit automatically. If that happens, press and

hold the [ ] button to re-initiate RCC receiving.

5. RCC receiving will automatically start at 2:03, 3:03,

4:03, 5:03 every night. Auto receiving function will

cease if it is successful.

6.To stop RCC reception, press and hold the

[ ] button.

7. If the device is still not receiving the signal, please

proceed to set the time manually.

NOTE: When using a power adapter, please increase

the separation of the main unit and the power adapter

to avoid interference of RCC signal receiving.

SET THE CLOCK MANUALLY

1. Press and hold [ ] button to enter into time and

date setting.

2.The setting parameter will flash.

3. Press [ ] button once, the figure will increase 1 unit

(when setting minute, second will reset to 0). Press

and hold the [ ] button, the figures will increase

rapidly.

4. Press [ ] button once, the figure will decrease 1 unit

(when setting minute, second will reset to 0). Press

and hold the [ ] button, the figures will decrease

rapidly.

5. Press [ ] button to confirm setting and enter to

next parameter.

6.Sequence of setting: Time Zone 12/24 Hr format

Hour Minute Year Calendar Mode (day-

month/month-day) Month Day Weekday

Language °C/°F  Exit

7. If there is no action in 20 seconds, the setting will be

saved and will exit the setting mode.

LANGUAGE

The Language options are: English (E), German (D) 

French (F) Italian (I) Spanish (S)

TIME ZONE SETTING

To set a different time zone, proceed as follows:

1.Press and hold [ ] button, enter time and date

setting.

2.The Time zone offset setting will flash.

3.Press the [ ] button to increase or [ ] button to

decrease the Time zone offset.

°C/°F SETTING

1.Press and hold [ ] button, enter time and date

setting.

2.Press [ ] button several times until the display

shows °C/°F.

3.Press the [ ] or [ ] button to switch Celsius (°C) /

Fahrenheit (°F).

ALARM

SETTING/ADJUSTING DUAL ALARM TIME

You can set two alarm times (AL1 and AL2).

1. Press the [ ] button to display Alarm 1.

2.Press and hold [ ] to enter the alarm setting

mode for the currently selected alarm (Alarm 1).

3.The setting parameter will flash.

4. Press [ ] or [ ] button to set the desired data.

5. Press [ ] button to confirm setting and enter to

next parameter.

6.Sequence of setting: Hour Minute  Exit

7. The alarm will sound when the alarm setting is

finished and turned on.

8. If there is no action in 20 seconds, the setting will be

saved and will exit the setting mode.

TURN ON/OFF ALARM

1.In alarm display mode, press the [ ] button to

turn on/off the current alarm. when in calendar

display mode, the sequence is: AL1 on AL2 on

AL1+AL2 on AL1+AL2 off.

2. The alarm lasts 2 minutes and becomes faster and

faster over time.

OPERATION

1.At the set time, alarm signal rings.

2.During the alarm, press the [ ] button to

delay the alarm by 8 minutes.

3.If you do not press any button to stop the alarm, it

will automatically turn off after 2 minutes.

4. To stop the alarm, press [ ] or any other button

except SNOOZE.

5. The alarm will start again at the next alarm time,

unless you switch off the alarm function by pressing

the [ ] button.

PROJECTION

The projector displays the time or temperature on your

ceiling or wall and it can rotate 180°. It is easier to view

in a darkened room. For the optimal projection results,

place the unit within 1.5 - 2 m (5-6.5 ft) from the ceiling

or wall.

Tabla de contenidos

Idiomas:

Otros manuales de Despertador de Explore Scientific

Explore Scientific

Explore Scientific NDC1004 Manual de usuario

Explore Scientific

Explore Scientific RDP3007-CM3000 Manual de usuario

Explore Scientific

Explore Scientific RDC1000 Manual de usuario

Explore Scientific

Explore Scientific RDC1005 Manual de usuario

Explore Scientific

Explore Scientific RDC3006-CM3000 Manual de usuario

Explore Scientific

Explore Scientific RPW3008-CM3000 Manual de usuario

Explore Scientific

Explore Scientific RDC8001 Manual de usuario

Explore Scientific

Explore Scientific RDP1003-CM3000 Manual de usuario

Explore Scientific

Explore Scientific BCR2001 Manual de usuario

Explore Scientific

Explore Scientific RDP1001 Manual de usuario

Explore Scientific

Explore Scientific RDC1005-CM3000 Manual de usuario

Explore Scientific

Explore Scientific RDC3006 Manual de usuario

Explore Scientific

Explore Scientific RDC1004-CM3000 Manual de usuario

Explore Scientific

Explore Scientific RDC1008 Manual de usuario

Explore Scientific

Explore Scientific RDP1002 Manual de usuario

Explore Scientific

Explore Scientific RDP1001-CM3000 Manual de usuario

Explore Scientific

Explore Scientific RPW3008 Manual de usuario

Explore Scientific

Explore Scientific RPW3008 Manual de usuario

Manuales populares de Despertador de otras marcas

Steren

Steren CLK-210 Manual de usuario

COP-USA

COP-USA ALCDVR32-SL Manual de usuario

Philips

Philips HF3505/70 Manual técnico

Casio

Casio PQ-70 Manual de usuario

iHome

iHome IA63 Manual de usuario

Coopers

Coopers 9765 Manual de usuario

ANJANK

ANJANK AC-190 Guía

TFA

TFA 98.1075 Manual de usuario

Sharper Image

Sharper Image 204050 Manual de usuario

Lumie

Lumie Zest Manual de usuario

Dexford

Dexford RCT200 Manual de usuario

Philips

Philips AJL303/37B Manual de usuario

RST

RST Q754 Manual de usuario

iHome

iHome iKT50 Manual de usuario

Sony

Sony dash HID-B7 Manual de usuario

SVINZ

SVINZ SCC009 Manual de usuario

Clas Ohlson

Clas Ohlson 918863 Manual de usuario

IKEA

IKEA FNURRA Manual de usuario