Expero Omega SAT Manual de usuario

USER MANUAL

of ALARM SYSTEM

with GSM/GPS

Omega SAT

~ 1 ~

OMEGA SAT is an advanced vehicle alarm system designed for cars with the

original remote control central lock and the CAN-BUS. It has a built-in GSM

modem and has the option of connecting a GPS module. OMEGA SAT provides a

reliable engine immobilization for the prevention of the vehicle’s theft. I also

features a 4-digit PIN code that overrides the alarm system in the case of an

emergency.

The set

a) system unit with wire harness;

b) built-in GSM modem;

c) user manual;

d) GPS module (optional);

e) siren (optional);

SYSTEM UNIT

The system unit performs the essential guarding functions thus it is

extremely important to hide it well in the vehicle. The manufacturer supplies

the alarm system with 4-digit PIN code, with is written on the alarm system

information sticker. Is recommended to write down the new PIN code,

however, do not keep this information inside the vehicle. In addition do not

use your birthday date or home address numbers for the PIN for security.

USING THE ALARM SYSTEM

REGULAR ARMING

For arming the system, press the remote control LOCK button shortly. The

vehicle direction indicators flash. The system LED will go ON, making constant

short flashes. When the system is armed, opening the vehicle's door, bonnet

or luggage compartment, vehicle's body tilt/impact to the vehicle’s body will

trigger the alarm system

Plate

PIN code

~ 2 ~

SENSOR BYPASS WITH THE HELP OF THE OVERRIDE BUTTON

With the ignition turned OFF press the override button. Watch the system's

LED, its flash will mean that the press has been confirmed. Get out the car,

close the doors and lock the Central Lock with the remote's LOCK button

within 20 seconds. The siren will make a long (0.5 second) confirmation sound

(if this feature is set by installer) to inform you that the system is armed with a

bypassed tilt/shock sensor(s) and the tilt/impact to car's body will not trigger

the alarm.

SENSOR BYPASS WITH THE HELP OF THE IGNITION KEY

Turn the ignition ON and OFF three times. Watch the system LED, its flash will

mean that the third ON/OFF procedure is confirmed. Get out the car, close the

doors and lock the Central Lock with the remote's LOCK button within 20

seconds. The siren will make a long (0.5 second) confirmation sound (if this

feature is set by installer) to inform you that the system is armed with a

bypassed tilt/shock sensor(s) and that tilt/impact to car's body will not trigger

the alarm.

ALARM INTERRUPTION

The system will trigger the alarm if the vehicle's doors, bonnet or luggage

compartment are opened, the ignition is turned ON or the ultrasonic sensor is

triggered. To interrupt the alarming of the system disarm and re-arm it.

DISARMING THE SYSTEM

Press the remote control UNLOCK button once shortly. The vehicle direction

indicators will flash. The system's LED will turn OFF

THE OVERRIDE MODE.

Alarm system override mode is used for cases such as the loss of the remote

control unit, the remote's battery becoming completely discharged or in the

case of the car being repaired. With this mode ON, the alarm system does not

respond to the sensor(s), does not immobilize the engine and does not alarm

(N.B. the system's LED flashes frequently). The override mode can be turned

ON in two ways with the PIN code.

~ 3 ~

TURNING ON THE OVERRIDE MODE WITH THE HELP OF THE OVERRIDE

BUTTON

The most convenient way to turn ON the override mode is to enter the PIN

code with the override button. If the override button is installed, check your

notes with the alarm system's PIN on, press the override button as many times

as the value of the first digit of the PIN (the time between the presses should

not exceed 1 second) and wait for a 1 second lasting LED flash, which will

mean that the first digit is entered successfully. In the same way enter the

second, third and fourth digits of the PIN.

To the next presses of the override button the system will respond as if the

PIN code is being entered.

TURNING ON THE OVERRIDE MODE WITH THE IGNITION KEY

If the override button is not installed, open the vehicle's door and turn the

ignition ON. Shortly after the system LED starts flashing double flashes, count

until the number of double flashes (1 double flash = 1 unit) corresponds with

the first digit of the PIN code. Turn the ignition OFF for a short time and turn it

ON again. Count the double flashes until the number corresponds with the

second digit of the PIN code. Turn the ignition key OFF and ON again. Enter the

remaining two digits of the PIN code in the same way. Upon correct entry of all

four digits of the PIN code the LED emits frequent flashes.

If you make a mistake while entering the PIN code, turn OFF the ignition,

close the doors, and follow all over again.

TURNING OFF (EXIT) THE OVERRIDE MODE

Enter the PIN code and enter the code '11' within 8 minutes of the previous

step.

~ 4 ~

EXTRA FEATURES

The extra features allows you to have an increased level of security for the car

and the driver if it is required. The installer will comment which extra feature is

turned ON.

AUTOMATIC REARMING

The alarm system is automatically armed, if the vehicle door, bonnet or

luggage compartment is not opened and the ignition is not turned ON within

45 seconds after the system is disarmed. However, it will not lock the doors of

the vehicle. It is possible to turn OFF the auto-rearming feature during the

installation of the alarm system.

ARM DELAY TIME

After the LOCK button is pressed, the system will wait the pre-set time limit

(default setting is 5 seconds, installer is able to set it up to 45 seconds) to

avoid false alarms due windows or sunroof closing.

If the door, luggage compartment or bonnet are not closed the alarm

system siren will make three short beeps after the pre-set time has elapsed.

The system will be armed anyway, but the open entry (for example door) will

not be protected until it is closed. The system will confirm the closing of a door

or compartment by a short siren beep and a single flash of direction indicators

~ 5 ~

CHANGING THE PIN CODE

The user has a possibility to change the PIN code. In order to do that, do the

following steps:

a) enter the current PIN code, the system's LED will emit single flashes

frequently;

b) in the same way as the PIN was entered before, enter the code '88'. The

entry will be confirmed by a short flash of direction indicators;

c) within 8 minutes of the previous step enter the new PIN twice, one after

another. In a case the same code was entered twice, the system will record

this as the new PIN code and confirm it by a short siren sound;

d) if a mistake is made while entering the PIN code, the system will inform

you by a short flash of the direction indicators. Wait for the frequent flashes of

the system's LED and follow the steps from c) all over again.

~ 6 ~

OPERATING THE SYSTEM THROUGH THE PHONE (GSM)

OMEGA SAT has a built-in GSM modem that allows, in addition to receiving

information about the system status (armed / disarmed, burglary, weak battery,

etc.), also its control (arming / disarming the system, turning on the start block)

For operation, the modem only needs a valid SIM card. It must be properly

prepared: PIN code request disabled, service center numbers entered, SMS

memory cleared. If the PIN code request is necessary, the device can

automatically enter the PIN code

The user via voice channel and SMS commands can:

a) adjust the communicator settings;

b) change the settings of the alarm system function (NOTE: it is not

recommended to change the settings yourself);

c) obtain information about the system status, vehicle position, and manage

alarms.

Alarm messages and information messages

In the list of numbers, you can save up to 5 phone numbers with which,

depending on the settings, the system will make calls and / or send SMS

messages. For each number you can set independently::

–Mandatory voice notification in the event of an alarm.

If the system is configured so that after triggering it connects to several

numbers, then the number that has this function set will ring, even if it receives

a confirmation response when connected to another number. If the user does

not receive a call or has answered but has not entered a confirmation code (# 0

or # and PIN code), the system will attempt to repeat the call 3 times.

–Voice notification in the event of an alarm.

If the system is configured to connect to several numbers after triggering, if a

connection with another number receives a confirmation reply, the system will

not call. If the user does not receive a call or has answered but has not entered a

confirmation code (# 0 or # and PIN code), the system will attempt to repeat the

call 3 times.

–SMS notification in the event of an alarm.

–SMS about arming.

–SMS about disarmament.

~ 7 ~

–SMS about problems (eg battery voltage is less than the set threshold).

–Periodic test SMS. SMS about the system state at the specified time (1 to 4

days) state at 12:00 noon.

–Sending unintelligible SMS.

If the function is enabled, the system will send back an unintelligible SMS.

Note: If you are blocked from answering calls and SMS commands from

unregistered numbers, each SMS from such number is also considered as

incomprehensible.

–SMS SmartPhone format.

This setting is important when using a mobile phone with the Android operating

system and the 'SecoLink Pro' application. In other cases, the function must be

turned off.

Calls and SMS messages to the number of the alarm system.

If it is blocked to answer a call and execute SMS commands from unregistered

phone numbers, each SMS from such a system number is also considered

unintelligible. This limitation does not apply (connections and SMSes can be

received from all numbers) if the system is in service mode (LED flashes quickly).

To send a tone command (it is not important from what number we call the

registered or not):

- Call the SIM card number.

- Using the telephone keypad, enter the correct PIN code and press #.

- Enter the command (see Voice channel command table.) And press #. The

DTMF code is sent immediately after pressing, so there is no point in correcting

the incorrectly entered digits. For incorrect commands instead of #, press *, then

enter the correct command, and press #.

~ 8 ~

To send a command in the form of an SMS message:

–If the command is sent from a telephone number not stored in the device's

memory, enter the system's PIN code at the beginning of the SMS.

–The PIN code does not have to be entered if the command is sent from the

telephone number stored in the device and the PIN code requirement for this

number is switched off.

–The commands begin with * and end with * #.

For each of the telephone numbers, the following settings are possible:

- The requirement to enter a PIN code in the SMS command.

If the option is enabled and the SMS command is not preceded by a valid PIN

code, the system accepts the SMS as incomprehensible.

- Prohibition of system control.

SMS from this number the system will find incomprehensible and the voice call

will reject. The setting is for an additional telephone number, e.g. for protection.

In case of incorrect setting of the function for the main number: activate the

service mode, deactivate the function with the SMS command and deactivate

the service mode.

- Changing the system state with a short signal.

If the system receives calls from this number, not immediately (waiting about 5

seconds), and if the connection is interrupted before it is received, the alarm

system will change its state (if disarmed, armed - and vice versa)).

Tabla de contenidos

Otros manuales de Alarma de coche de Expero

Expero

Expero Omega IMMO Manual de usuario

Manuales populares de Alarma de coche de otras marcas

Clifford

Clifford 3606X Manual de usuario

Ultra Start

Ultra Start 2500M SERIES Manual de usuario

Ultra Start

Ultra Start 650 Series Manual de usuario

Audiovox

Audiovox Prestige Platinum+ APS-511C Manual de usuario

Sparkrite

Sparkrite SRA8 Manual de usuario

Viper

Viper 4708V Manual de usuario

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manual

Falcon

Falcon Predator XL3 Guía del usuario

Audiovox

Audiovox Auto Security XR91 Instrucciones de funcionamiento

Clifford

Clifford Sabre II Manual de usuario

CrimeStopper

CrimeStopper CS-8717 Guía de inicio rápido

Ultra Start

Ultra Start 450 SERIES Manual de usuario

Scytek electronic

Scytek electronic Vectra X3 Manual de usuario

Excalibur

Excalibur AL-1860-EDPB Manual de usuario

Clifford

Clifford CYBER 2 Manual de usuario

Gemini

Gemini 7057 Manual de usuario

FlashLogic

FlashLogic FLRSBA PRESTIGE Manual de usuario

Magicar

Magicar FAI-440 Manual de usuario