Exalux LEDMASTER STUDIO 1 Manual de usuario

1 - GENERAL INFORMATION

This hardware instruction manual contains speciﬁcations and important notiﬁca-

tions regarding the safe use of the EXALUX™ LEDMASTER STUDIO 1.Please take the

time to read this manual carefully and thoroughly before installing and operating

the device. We recommend that you keep a copy for future use and transfer it to

the buyer if you resell the device.

EXALUX™ reserves the right to modify and upgrade its range of products, with no

obligation to integrate these changes into products already sold.Therefore,all the

information found in this manual is subject to change without notice.

2 - OVERVIEW

EXALUX™ LEDMASTER STUDIO 1 is a single channel high output constant voltage

LED dimmer. It has been designed to dim up to 360W LED ﬁxtures (depending on

the version), controlled from DMX/RDM console or CRMX transmitter (optional).

This dimmer is integrated in a standard DIN rail enclosure with 5.08mm pluggable

terminal blocks for quick and easy set-up.The LEDMASTER STUDIO 1 is available in

several versions which can be equipped with LumenRadio™ CRMX receiver.

Input Output Designation DMX/RDM Wireless CRMX

30W 12VDC LM-STUDIO1-AC30-12

-D -W

(optional)

24VDC LM-STUDIO1-AC30-24

60W 12VDC LM-STUDIO1-AC60-12

24VDC LM-STUDIO1-AC60-24

DC 7.5Amax/pin

(180W@12V / 360W @24V) LM-STUDIO1-DC360

3 - FEATURES

- AC input/output for power supply daisy chain,

- Low side PWM constant voltage output,

- Wired DMX/RDM input/output interface,

- Wireless DMX/RDM integrated receiver (CRMX by LumenRadio™),

- Long range whip, hinged and removable antenna,

- LED indicators, pushbutton, trigger input port,

- DMX address settings, 3x 10 positions rotary switches,

- Custom settings (mode, DMX fail,PWM frequency,dimming curve), 1 x DIP switch,

- Local (manual) dimming control, 16 positions rotary switch,

- Software updates from DMX interface,

- Small form factor, DIN rail, pluggable terminal blocks.

LEDMASTER STUDIO 1

4 - BLOCK DIAGRAM

5 - INPUTS/OUTPUTS

DMX/RDM OUT

DMX/RDM IN

DC INPUT

(-DC360 version)

AC INPUT

(-AC versions)

TRIGGER INPUT

DMX/RDM

CONTROLLER

AC OUT

(-AC versions)

CRMX

CONTROLLER

LED SPOT / LED STRIP

(Output power and voltage

depending on dimmer versions)

(-W version)

AC In/Out

(only for AC versions)

DC Input

(only for DC versions)

DMX In/Out

Power LED

indicator (red)

Reset/Unlink

switch

2,4GHz SMA

mount antenna

(only for CRMX versions)

3x CRMX signal level

LED indicators (green)

(only for CRMX versions)

CRMX status LED indicator (blue)

(only for CRMX versions)

DMX data LED

indicator (blue)

PWM

Output

Trigger

Input

(dry contact)

Settings

(10

positions

DIP

switch)

Manual dimming

(16 positions

rotary switch)

DMX address

(3x 10 positions

rotary switches)

6 - POWER SUPPLY

Version -AC30-12 -AC60-12 -AC30-24 -AC60-24 -DC360

Input Voltage 85~305VAC / 47~440Hz 12 to 24VDC

Output Voltage 12VDC 24VDC 12 to 24VDC

Power Rating 30W 60W 30W 60W 180W @12VDC

360W @24VDC

Current Load 2.5A 5A 1.25A 2.5A 15A

AC version:

The LEDMASTER STUDIO 1 integrates a built-in AC/DC converter.The output power

and voltage depends on the version.Do not daisy chain more than 20 LEDMASTER

STUDIO 1 on the AC line. Exceeding this limit can cause overheating of connec-

tors and damage the printed circuit board.

DC360 version:

The typical input voltage of LEDMASTER STUDIO 1 is +12 to +24VDC. Using the

dimmer outside of this range can cause malfunctions and even destruction of

the device. Input voltage is monitored in case of over voltage detection (device

shutdown) and can be read from a RDM controller.

Static DC input voltage & PWM output voltage are electrically connected. Input

is protected against polarity inversion. Maximum current should not exceed 7.5A

per contact on terminal blocks and cables. In case of a load higher than 7.5A, it

is imperative to distribute the power on the four input and output pins.

7 - GENERAL SPECIFICATIONS

AC Power input/Passthrough 2x 5.08mm terminal block (black), 2 positions (L+N)

DMX input/Passthrough 2x 5.08mm terminal block (green), 3 positions (GND, D+, D-)

PWM output

1 channel, 0 to 100%, low side PWM technology

Adjustable frequency (4, 8, 16 or 32kHz)

1x 5.08mm terminal block (green), 2/4 positions (V+, PWM OUT)

Dimming Curve Linear, Logarithm, Exponential & Custom

Modes Local (manual), DMX/RDM, CRMX,Test

Controls Local (rotary coded wheels & DIP switches) & DMX/RDM

Trigger Input 1x 5.08mm terminal block (orange), 2 positions (dry contact)

Display LED indicators

Dimmer own consumption <1W

Firmware update Bootloader, via speciﬁc cable on DMX input

Housing / Mounting DIN Rail 8M enclosure (142,3 x 90,5 x 64,9mm) plastic (PC/ABS), grey (RAL7035),

DIN rail (EN 60715) mounting (with plastic hook)

Protection, IP rating IP2X (indoor use only)

Certiﬁcations

Weight Min : 160g (-DC360-D version) | Max : 370g (-AC60-W version, with antenna)

Storage T° Min : -30°C | Typ : 25°C | Max : +80°C

Operating T° Min : -20°C | Typ : 25°C | Max : +50°C

8 - SETTINGS

The parameters of the LEDMASTER STUDIO 1 can be changed from the DIP switch

“SETTINGS”, or from a RDM controller (only in RDM mode, refer to RDM section for

details).

# SETTING DESCRIPTION

S1-S2 MODE Selection of the operating mode:

- “00”= DMX/RDM, Device control from wired DMX interface (Refer

to DMX section for details)

- “01”= Manual, Allows user to control the output brightness from

the local rotary switch (Refer to Manual Dimming section

for details)

- “10”= CRMX/RDM, Device control from wireless CRMX interface.

(Refer to CRMX section for details)

- “11”= Test,Allows user to test the device when installing, without

any controller (Output brightness variation loop, indicators

blinking).

S3 DMX RESOLUTION Switch between 8 bits and 16 bits DMX resolution for ﬁne/coarse

adjustments:

- ”0” = 8 bits

- ”1” = 16 bits

S4-S5 PWM FREQUENCY Output PWM frequency selection:

- “00”= 32kHz

- “01”= 16kHz

- “10”= 8kHz

- “11”= 4kHz

S6-S7 DMX FAIL Select the behaviour in case of DMX stream interruption (lost

signal, DMX cable issue, controller Off …):

- ”00”= Hold (Hold the current/last valid DMX values)

- ”01”= Black (Forced blackout, turn off output)

- ”10”= Man. dimming (Apply the brightness output according

to the value set on the “Manual Dimming” Rotary switch.

Refer to MANUAL MODE section for details)

- ”11”= Full (Forced Full-On, turn on output)

S8 DMX FADING Assigns an additional DMX channel for fading timing adjustment,

20ms steps, from ‘‘000’’ (no fading) to ‘‘255’’ (= 5s fading time)

S9-S10 DIMMING CURVE Output dimming curve selection:

- “00”= Linear

- “01”= Logarithmic

- “10”= Exponential

- “11”= Custom (optimized for 18,5W 12V AR111 LED spot at 32kHz)

Refer to DIMMING CURVE section for details.

9 - DMX

To enable the DMX feature, the device must be set in DMX mode (S1-S2 = “00”).

When DMX signal is received, the blue “DMX Data” indicator turns ON.

Use the three rotary switches to set the DMX address. In case an out of range

address is entered, the device will automatically assign the highest DMX address

usable.

Note: The DMX address “000” is reserved for RDM control. When “000” address is

selected, the default DMX address is “001”.

Protocols DMX512-A & RDM (ANSI E.1.20) - RDM manufacturer ID:“0084h”

Universe 1

DMX frame rate 0,8-830Hz

DMX input/output 1x DMX input/Passthrough, 2x 5.08mm terminal block (green), 3 positions

DMX options

DMX resolution: 8 bits or 16 bits

DMX fail: Hold, Black, Full or Manual setting

DMX fading: On/Off

DMX CHARTS: Addr Addr+1 Addr+2

DMX - 8bits Output brightness

(0% to 100%) - -

DMX - 16bits Output brightness

(0% to 100%, MSB/Coarse dimming)

Output Brightness

(LSB/Fine dimming) -

DMX - 8bits + Fading Output brightness

(0% to 100%)

Fading

(0s to 5s) -

DMX - 16bits + Fading Output brightness

(0% to 100%, Coarse dimming)

Output Brightness

(Fine dimming) Fading (0s to 5s)

10 - RDM

To enable the RDM control, the device must be set in DMX or CRMX mode (S1-S2

= “00” or “10”) and the DMX address must be set to “000”.

When the DMX address “000” is selected, DMX modes (resolution, fading) can be

changed from RDM controller. In that case, values sets on the DIP switch settings

do not necessarily correspond to the current operating mode.

The RDM features can be used on both wired DMX and wireless CRMX.

- RDM manufacturer identiﬁer: «0084h».

- RDM labels:‘‘LEDMASTER STUDIO 1 DMX’’ & ‘‘LEDMASTER STUDIO 1 CRMX’’

- RDM sensors: input voltage & CRMX signal reception (for CRMX versions only)

The device supports the following RDM PIDs:

DISC_UNIQUE_BRANCH

DISC_MUTE

DISC_UN_MUTE

SUPPORTED_PARAMETERS

DEVICE_INFO

FACTORY_DEFAULTS

SOFTWARE_VERSION_LABEL

DMX_START_ADDRESS

IDENTIFY_DEVICE

DEVICE_MODEL_DESCRIPTION

MANUFACTURER_LABEL

SENSOR_DEFINITION

DEVICE_LABEL

DMX_PERSONALITY

DMX_PERSONALITY_DESCRIPTION

SLOT_INFO

SLOT_DESCRIPTION

SENSOR_VALUE

11 - CRMX RADIO INTERFACE

Standard / Technology CRMX by LumenRadio™

Frequency 2.402 ~ 2.480 GHz

Antenna Swivel whip omnidirectional, 2.4GHz 2.0dBi, SMA (SMA-F onboard, SMA-M on antenna)

RF Output 20 dBm (100mW) - ETSI compliant

RF Modulation GFSK

End to end latency < 5ms

Range Up to 300m (depending on the transmitter and the environment)

Interface 3x green LEDs for radio signal level, 1x pushbutton (hold 3s to unlink from transmitter)

LEDMASTER STUDIO 1 embeds a radio CRMX receiver, RDM compliant, based on

LumenRadio™ technology, enabling to receive a single wireless DMX universe.To

enable the CRMX feature, the device must be set in CRMX mode (S1-S2 = “10”).

Antenna orientation should be optimized according to the expected radio perfor-

mances and the LEDMASTER STUDIO 1 environment.

Link procedure:

- Make sure that both devices are powered, and dimmer is unlinked.

- Start the linking procedure on the transmitter.

- During the linking procedure (~10s), any unlinked receiver in range will

automatically link to the transmitter.

If LEDMASTER STUDIO 1 is linked to a transmitter, the blue Status LED

indicator turns on (even if the transmitter is off).

- During the linking procedure, the DMX signal is not transmitted.

Unlink procedure:

- Long press (>3s) the pushbutton on the dimmer until the status indicator

turns off.You can also unlink all linked receivers from the transmitter.

Signal level indicators:

- Blinking = no signal

- 1 LED = poor reception

- 2 LEDs = correct reception

- 3 LEDs = excellent reception

Status indicator:

- Off: Device is not linked to any transmitter

- Flashing: off 100ms / on 100ms: Device is linked but no active radio link

- Flashing: off 900ms / on 100ms: Device is linked, no DMX present

- On: Device is linked to a transmitter, DMX data present

Once everything is set up,the LEDMASTER STUDIO 1 works the same way as it does

for wired DMX: the address and mode are the same.

12 - MANUAL DIMMING

To enable the MANUAL DIMMING feature,the device must be set in manual mode

(S1-S2 = “01”). In this mode, the output brightness can be manually controlled

from the 16 positions rotary switch. Use a small ﬂat screwdriver to select the value.

The ﬁrst 10 positions (0 to 9) allows to adjust with 5% steps, the last 6 positions (A

to F) allows to adjust with 10% steps.

00% (Off) 525% A50%

15% 630% B60%

210% 735% C70%

315% 840% D80%

420% 945% E90%

F100% (Full On)

13 - DIMMING CURVES

14 - TRIGGER

The trigger input is a dry-contact between the two pins of the terminal block connector. Do

not apply any voltage on this input.Dry contact trigger input should be used with passive

switches, in respect with the common GND equipotential reference.

- In DMX & CRMX mode, when the contact is closed, the DMX/CRMX commands are

by-passed and the value set on the 16-position rotary switch is applied to the output.

- In manual mode, when the contact is closed, the output is turn off (black out).

15 - INSTALLATION & CABLING

LEDMASTER STUDIO 1 enclosure is designed to be mounted onto a standard DIN rail 35mm

width (EN 60715), but wall mounted is another option. Use the embedded plastic hook to

attach or detach from the rail.This device is delivered with all required terminal block plugs.

16 - FACTORY RESET

To factory reset the device,press and hold the RESET push button during 10secs.The device

will ﬂash memory to default factory settings and restart.

Note: Hardware settings on the DIP switch (SETTINGS) and rotary switches (DMX ADDRESS,

MANUAL DIMMING) will be automatically restored.

17 - DRAWINGS

64.90mm 108mm

91mm

98mm

170.65mm

142.30mm

Note 1: the CUSTOM dimming curve

has been optimized for 18,5W 12V

AR111 spot at 32kHz

Note 2: dimming curves correspond

to the 8 bits mode (0-255), but 16 bits

mode is very similar

Last update : Feb. 2021

18 - SAFETY INSTRUCTIONS

Term of use

This system is designed to control lighting sources, for indoor use only. To prevent damage, do not

expose it to liquid or moisture and keep the devices away source of heat and ﬂames.Avoid clogging

and strong vibrations. Use the devices only in its intended use as described in this manual.Any other

use, as well as use in other conditions, will be considered non-compliant and can cause injury and

damage. No liability will be assumed for damages resulting from improper use.

Risk of electric shock

This device operates AC/DC conversion and regulation, which can result in an electrical shock.Do not

remove cover when powered, do not disassemble.The parts inside the device are maintenance free.

Check the feature compliancy and correct operation of the power supply before connecting it to

the device. Before connection, check if the voltage corresponds to the voltage of your local power

network and if the socket is equipped with a GFCI. In case of non-compliance, the device may be

damaged and the user may be injured. In case of non-compliance, there is a risk of electric shock

and ﬁre hazard. If in doubt, contact a certiﬁed technician.

Load

Check the feature compliancy and correct operation of the power supply unit, dimmer and LED ﬁxture

before connecting it. In case of non-compliance, devices may be damaged and the user may be

injured.

Cable

The section of power cables on AC and DC input / output should match the load power requirements

and the cable length should be minimized as much as possible,in order to avoid voltage dropout and

heating. Use only the connectors delivered with the device. If those instructions are not complied, the

system may exhibit inconsistent behaviour.

Care

Unplug LEDMASTER STUDIO 1 before cleaning it. Do not use cleaning product, use a dry cloth and rub

gently. Gently wipe off any stains with a soft lint-free cloth. Store the devices in a clean and dry place,

away from exposure to direct sunlight and dust.

Maintenance

Unplug the devices from power during all maintenance operations. The device should only be ins-

talled and opened by people in full possession of their physical,sensory and mental abilities who must

have the required knowledge and experience. All the other persons are only allowed to operate the

devices under the supervision or direction of a person responsible for their safety.

Warranty

EXALUXTM cannot be responsible for material or personal damage resulting from improper use of the

product or non-compliance to the instructions.The warranty will not be applied in these cases.

EXALUXTM is a registered trademark of the French Tech Company LEDIXIS

1 rue de la Noë

Bâtiment IM3

CS 12111

44322 Nantes Cedex 3

FRANCE

+33 (0)9.72.45.70.43

www.exalux.eu

Information: contact@exalux.eu

Technical support: support@exalux.eu

Tabla de contenidos

Otros manuales de Mando a distancia de Exalux

Exalux

Exalux CONTROLSKY Manual de usuario

Exalux

Exalux CONTROL TOUCH Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación