Exabyte Mammoth Manual de usuario

319932-000

December 1996

#319932-000#

Contents

1 Before you begin . . . . . . . . . . . . . . . . . . . . . . . 2

2 Disconnecting the LCD flex cable. . . . . . . . . . 3

3 Replacing the faceplate. . . . . . . . . . . . . . . . . . 4

4 Connecting the LCD flex cable . . . . . . . . . . . . 6

5 Replacing the top cover . . . . . . . . . . . . . . . . . 7

6 After replacing the faceplate . . . . . . . . . . . . . 8

FIELD INSTRUCTIONS

Exabyte Mammoth 8mm Tape Drive

Replacing the Faceplate

Page 2 of 8 319932

herein are the property of Exabyte Corporation. No part of this document may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language or computer

language in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise, without the express written permission of Exabyte Corporation, 1685 38th Street, Boulder,

Colorado 80301.

Trademark Notices

EXABYTE, EXAPAK, EXB, FileSECURE, LANCourier, and NetSECURE are registered trademarks of

Exabyte Corporation. Eagle, EXA, EXAFacts, EXA

soft

, EXATAPE, Nest, and SCIMON are trademarks of

Exabyte Corporation. All other product names are trademarks or registered trademarks of their

respective companies.

1 Before you begin

To protect the tape drive from ESD, follow these procedures when repairing

or testing it:

Place a static protection mat on the work surface used for tape drive

components. Use a 1-megohm resistor to ground the static protection

mat.

Wear a static protection wrist band whenever you handle tape drive

printed circuit cards. Connect this wrist band to the static protection mat

or to other suitable ESD grounding.

If there is a cartridge in the tape drive, remove it before performing any

maintenance procedure.

Required tools

Torque limiting screwdriver

T-6 TORX bit

CAUTION

Before you begin, make sure that the repairenvironment

for the tape drive is free of conditions that could cause

electrostatic discharge (ESD).

December 1996 Page 3 of 8

Disconnecting the LCD flex cable

2 Disconnecting the LCD flex cable

If your tape drive has an LCD, follow the instructions in this section to

disconnect the LCD flex cable before you remove the faceplate.

If your tape drive does not have an LCD on the faceplate, skip this section

and go to Replacing the faceplate on page 4.

Using a T-6 screwdriver, remove the two side screws and one rear screw

that attach the top cover to the tape drive (see Figure 1).

To remove the top cover, slide it back about1 inch (2.6 cm). Lift the front

edge first, and then remove the cover.

Figure 1

Removing the top cover

Page 4 of 8 319932

Replacing the faceplate

Unlock the LCD flex cable connector by pulling one end of the tab and

then the other toward the cable (see Figure 2).

Gently pull the LCD flex cable out of the connector.

3 Replacing the faceplate

Note:

The instructions in this section apply to both LCD and non-LCD

faceplates. However, the illustrations in this section show a

faceplate with an LCD.

Press in the faceplate tabs on both sides of the tape drive, as shown in

Figure 3. Pull the faceplate straight out from the tape drive.

Figure 2

Loosening the LCD flex cable connector

CAUTION

Make sure you pull the faceplate straight out to remove

it. If you tilt or twist the faceplate, you could damage

the LED card on the left side of the tape drive.

December 1996 Page 5 of 8

Replacing the faceplate

If you are replacing a non-LCD faceplate with an LCD faceplate, follow

the instructions on page 3 to remove the top cover of the tape drive.

Placethetapedriveonaflatsurface.Alignthebottomofthereplacement

faceplate with the bottom of the tape drive. Position the LED guard on

the back of the faceplate on the left side of the tape drive.

Position the faceplate tabs inside the side panels, as shown in Figure 4,

and press the faceplate onto the tape drive.

Figure 3

Removing the faceplate

CAUTION

Make sure you align the bottom of the faceplate with

the bottom of the tape drive and position the faceplate

tabs inside the side panels before you attach the

faceplate. If you misalign the faceplate, you could

break the LEDs off the printed circuit card.

Figure 4

Positioning the faceplate

Page 6 of 8 319932

Connecting the LCD flex cable

If your replacement faceplate has an LCD, follow the steps in the next

section to connect the LCD flex cable.

If your replacement faceplate does not have an LCD and you removed

the top cover, skip the next section and go to Replacing the top cover

on page 7.

If your replacement faceplate does not have an LCD and you did not

remove the top cover, skip the next two sections and go to After

replacing the faceplate on page 8.

4 Connecting the LCD flex cable

Unlock the LCD flex cable connector by pulling one end of the tab and

then the other toward the cable (see Figure 5).

Slide the LCD flex cable allthe way into the connector on thecard. Make

sure the LCD flex cable is firmly seated in the connector.

Holding the flex cable firmly in place, press the tab into the connector

to close it.

Figure 5

Loosening the tab on the LCD flex cable connector

December 1996 Page 7 of 8

Replacing the top cover

5 Replacing the top cover

Place the top cover on the tape drive so that the back edge extends about

1 inch (2.6 cm) over the back of the tape drive. Slide the cover forward

carefully, guiding the tab on the top cover under the lip of the faceplate.

Replace the three screws that attach the top cover to the tape drive (see

Figure 6). Tighten the screws to 1.2 inch-pounds of torque.

CAUTION

A mylar flap inside the tape drive protects the cartridge

loader. Be careful not to catch the flap on the top cover

window as you slide the top cover forward.

Figure 6

Replacing the top cover screws

Page 8 of 8 319932

After replacing the faceplate

6 After replacing the faceplate

Apply power to the tape drive and insert a cartridge. Check the following

items:

Make sure the cartridgedoes not get caught on the faceplate during load

or unload operations.

When you remove the cartridge, make sure the tape drive door closes.

If you have a faceplate with an LCD, make sure the LCD operates

correctly. Refer to

Exabyte Mammoth Installation and Operation

(part

number 306484) for more information about the LCD.

If you experience problems, make sure the faceplate is positioned squarely

on the front of the tape drive and the LCD cable is securely seated in the

connector.

Otros manuales para Mammoth

Tabla de contenidos

Otros manuales de Almacenamiento de Exabyte

Exabyte

Exabyte 230D Library Manual del propietario

Exabyte

Exabyte 221L Manual de usuario

Exabyte

Exabyte VXA-172 Manual de usuario

Exabyte

Exabyte Magnum20 Manual de instrucciones

Exabyte

Exabyte VXA-2 Manual de usuario

Exabyte

Exabyte 8505XLS Instrucciones de funcionamiento originales

Exabyte

Exabyte EXB-8205 Manual de usuario

Exabyte

Exabyte Mammoth Manual de usuario

Exabyte

Exabyte Mammoth Manual de usuario

Exabyte

Exabyte EXB-8500 Manual del propietario

Exabyte

Exabyte 430 Manual de usuario

Exabyte

Exabyte EXB-8700 Manual de usuario

Exabyte

Exabyte VXA-1 Manual de usuario

Exabyte

Exabyte LTO-2 Manual de usuario

Exabyte

Exabyte EXB-8500 Guía

Exabyte

Exabyte 110L LTO Ultrium AUTOLOADER Manual de usuario

Exabyte

Exabyte Mammoth Manual de usuario

Exabyte

Exabyte EXB-8200 Manual de usuario

Exabyte

Exabyte EXB-8205 Manual de usuario

Exabyte

Exabyte EXB-8505 8mm Manual del propietario

Exabyte

Exabyte 8505XL Manual de usuario

Exabyte

Exabyte VXA-2 AUTOPAK1X7 Manual de usuario

Exabyte

Exabyte Mammoth-LT Manual del propietario

Exabyte

Exabyte 8505XLS Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario