Evoheat Evo Control 17 Manual de usuario

Evo Control 17 & 25 Manual

Contents

1. Introduction _________________________________________________________________________________2

2. Unit Specifications ____________________________________________________________________________2

2.1 Unit Structure_____________________________________________________________________________2

2.2 Dimensions_______________________________________________________________________________3

2.3 Technical Data ____________________________________________________________________________ 4

3. Safety Instructions ____________________________________________________________________________ 5

4. Installation __________________________________________________________________________________6

4.1 Application for Air-Con______________________________________________________________________6

4.2 Application for Air-Con and Super Heater (for Hot Water) __________________________________________6

4.3 Location of Install & Minimum Clearances ______________________________________________________7

4.4 Plumbing Component ______________________________________________________________________7

4.5 Electrical Component_______________________________________________________________________ 7

4.6 Transit __________________________________________________________________________________8

4.7 Trial Operation ____________________________________________________________________________8

5. Operation ___________________________________________________________________________________9

5.1 Main Controller Interface ___________________________________________________________________9

5.2 Functions of the Controller __________________________________________________________________ 9

5.2.1 Using the HELP Button __________________________________________________________________9

5.2.2 Starting & Shutting Down ________________________________________________________________ 9

5.2.3 Switching Modes______________________________________________________________________10

5.2.4 System State Checking _________________________________________________________________ 10

5.2.5 Changing Temperature _________________________________________________________________ 10

5.2.6 Clock Setting _________________________________________________________________________ 10

5.2.7 Timer Settings ________________________________________________________________________ 11

5.2.8 Keyboard Lock ________________________________________________________________________12

5.2.9 Malfunction Display ___________________________________________________________________12

6. Troubleshooting _____________________________________________________________________________ 13

7. Appendix __________________________________________________________________________________ 16

7.1 Install Sketch Map ________________________________________________________________________ 16

7.2 Installation of Automatic Filled-Water_________________________________________________________17

7.3 Installation of Leakage Pressure Valve_________________________________________________________17

7.4 Assistant Heat Source Connection ____________________________________________________________18

7.5 Unit Parameters __________________________________________________________________________ 18

7.6 PCB Connection __________________________________________________________________________ 19

7.7 Cable Specifications _______________________________________________________________________21

8. Maintenance _______________________________________________________________________________22

9. Warranty __________________________________________________________________________________23

Evo Control 17 & 25 Manual

1. Introduction

This manual contains all the necessary information in regard to the installation, troubleshooting, operation and

maintenance of this unit. Ensure instructions in this manual are adhered to at all times. Failing to comply with these

recommendations will invalidate the warranty. This manual and all others are available for download on our website.

The Evo Control Series air to water heat pump is designed for multiple-use household heating requirements. The Evo

Control provides energy efficient space heating/cooling and floor heating - ALL IN THE ONE UNIT!

The Evo Control Series is ideal for domestic space heating/cooling and floor heating.

2. Unit Specifications

2.1 Unit Structure

Evo Control 17 & 25 Manual

2.2 Dimensions

Evo Control 17

Evo Control 25

Evo Control 17 & 25 Manual

2.3 Technical Data

Evo Control 17

Evo Control 25

Cooling Capacity

13.5

19.5

Btu/h

46000

67000

Heating Capacity

17.0

25.0

Btu/h

58000

85000

Cooling Power Input

4.7

7.0

Heating Power Input

4.1

6.0

Running Current (Cooling/Heating)

20.4/17.8

12.1/10.3

Power Supply

230V~/50Hz

400V/3N~/50Hz

Compressor Quantity

Compressor

Rotary

Fan Quantity

Fan Power Input

120x2

200x2

Fan Rotate Speed

RPM

850

750

Noise

dB(A)

Hot water volume

L/h

Water Pump Input

0.2

0.75

Water Head

13.5

Water Connection

Inch

1.5

Water Flow Volume

m3/h

2.8

3.8

Water Pressure Drop

kPa

Unit Net Dimensions (L/W/H)

See unit drawing

Unit Shipping Dimensions

See package label

Net Weight

See nameplate label

Shipping Weight

See package label

Cooling: Ambient temperature 35°C / 24°C, inter/outlet water temperature: 12°C / 7°C

Heating: Ambient temperature 7°C / 6°C, inter/outlet water temperature: 30°C / 35°C

Evo Control 17 & 25 Manual

3. Safety Instructions

•Installation, repairs and maintenance of this unit must be performed by a qualified technician.

•Any wiring must comply with local electrical regulations.

•Ensure that the electrical supply corresponds to the specification indicated on the unit’s makers plate before

proceeding with the connection in accordance with the wiring diagram supplied.

•The unit must be earthed to avoid any risk caused by insulation defects.

•No wiring must come into contact with the heat source or the rotating fan parts.

•The unit must be handled and lifted with appropriate equipment in correlation with the unit’s size and weight.

•Electrical power must be switched off before any work is started on the unit.

•Do not work on the electrical components if water or high humidity is present on site.

•When the unit is being connected, ensure that no impurities are introduced into the pipework and water circuits.

A mesh filter must be provided on the hydraulic pump and in exchanger water inlets.

•If the supply cord is damaged, it must be replaced by the manufacturer.

•Do not expose the unit to or install near any flammable gases.

•Ensure there is a circuit breaker for this unit.

•The unit is equipped with an over-load protection system. After a previous stoppage, the unit will not start for at

least 3 minutes.

•At the end of the unit’s useful life, the unit must be taken to a recycling centre appropriate for electronic devices

and not domestic waste.

•Use supply wires suitable for 75°C

•Caution: Single wall heat exchanger, not suitable for potable water connection.

Evo Control 17 & 25 Manual

4. Installation

4.1 Application for Air-Con

4.2 Application for Air-Con and Super Heater (for Hot Water)

Evo Control 17 & 25 Manual

4.3 Location of Install & Minimum Clearances

The heat pump can be installed onto a concrete basement by using expansion screws, or onto a steel frame with

rubber feet which can be placed on the ground or the roof. Ensure that the unit is placed horizontally.

•The unit can be installed in any place outdoors which will be able to support the weight of a heavy unit such as a

terrace, roof, the ground and any other places deemed suitable.

•The location must have good ventilation.

•The location must be free from heat radiation and other fire hazards.

•In cold climates, a pall is needed in winter to protect the unit from snow.

•There must be no obstacles near the inlet and outlet of the unit.

•The installation location must be protected from strong winds or air.

•There must be a water channel around the heat pump to drain condensing water.

•Leave enough space around the unit for maintenance.

A>500mm B>1500mm C>1000mm D>500mm

4.4 Plumbing Component

Please pay attention to the below matters when the water pipe is connected.

•Try to reduce the resistance to the water from the piping.

•The piping must be clear and free from dirt and blockage. A water leakage test must be carried out to ensure

that there is no water leaking before the installation can be made.

•The pipe must be tested by pressure separately. DO NOT test it together with the unit.

•There must be an expansion tank on the top point of the water loop, and the water level inside the tank

must be at least 0.5meters higher than the top point of the water loop.

•The flow switch is installed inside of the heat pump, check to ensure that the wiring and action of the switch

is normal and controlled by the controller.

•Try to avoid any air from being trapped inside the water pipe, there must be an air vent on the top point of

the water loop.

•There must be a thermometer and pressure meter at the water inlet and outlet for easy inspection during

running.

4.5 Electrical Component

•Open the front panel and open the power supply access.

•The power supply must go through the wire access and be connected to the power supply terminals in the

controlling box. Then connect the 3-signal wire plugs of the wire controller and main controller.

•If an external water pump is required, please insert the power supply wire into the wire access and connect

it to the water pump terminals.

•If an additional auxiliary heater is needed to be controlled by the heat pump controller, the relay (or power)

of the aux-heater must be connected to the relevant output of the controller.

Evo Control 17 & 25 Manual

4.6 Transit

If the unit needs to be hung up during installation, an 8-metre cable is required. There must be a soft material

between the cable and the unit to prevent damage to the heat pump cabinet

WARNING: Do not touch the heat exchanger of the unit with fingers or objects.

4.7 Trial Operation

INSPECTION BEFORE TRIAL OPERATION:

•Check the indoor unit, make sure that the pipe connection is done correctly, and the relevant valves are open.

•Check the water loop to ensure that the water inside of the expansion tank is filled to an appropriate level, and

the water supply is working, and the water loop is full of water and free of trapped air. Make sure there is good

insulation for the water pipe.

•Check the electrical wiring. Make sure that the power voltage is normal, the screws are fastened, the wiring is

made in line with the diagram and that the earthing is connected.

•Check that the heat pump includes all the screws and components, and that they are in good order. When

powering the unit on, review the indicator on the controller to see if there is any indication of failure. The gas

gauge can be connected to the check valve to see the high pressure (or low pressure) of the system during trial

running.

TRIAL OPERATION:

•Start the heat pump by pressing the ‘UP’ or ‘DOWN’ arrow key on the controller.

Check whether the water pump is running, if it runs normally there will be 0.2MPa

on the water pressure meter.

•When the water pump has ran for a minute, the compressor will start. Listen for

any strange sounds from the compressor, if an abnormal sound occurs please stop the unit and check the

compressor. If the compressor runs well please look for the pressure meter of the refrigerant.

•Check whether the power input and running current is in line with the manual. If not please stop and check.

•Adjust the valved on the water loop to make sure that the hot (cool) water supply to each door is good and

meets the requirements of heating (or cooling).

•Review whether the outlet water temperature is stable.

•The parameters of the controller are set by the factory, the user cannot change these themselves.

Evo Control 17 & 25 Manual

5. Operation

5.1 Main Controller Interface

Button

Name

Function

ON/OFF Press this button to start up/shut off the unit, cancel current operation or go back to

previous interface.

HELP Press this button to check button function of system state.

MODE Press this button to change the current mode, page up or confirm current operation.

CLOCK Press this button to set the clock or turn the timer on/off.

UP Press this key to select the upwards option or increase the parameter value.

DOWN Press this key to select the downwards option or decrease the parameter value.

5.2 Functions of the Controller

5.2.1 Using the HELP Button

You can use at any interface and it will explain the buttons & functions of the current interface. To exit the help

interface, simply press the ON/OFF button.

EXAMPLE: Press HELP at the Main Interface

5.2.2 Starting & Shutting Down

To turn on/off the unit, press the ON/OFF button for 1 second. The screen will display as following for each state:

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Bomba de calor de evoheat

evoheat

evoheat Force-i Series Manual de usuario

evoheat

evoheat CS Manual de usuario

evoheat

evoheat EVO ULTRA 32 Manual de usuario

evoheat

evoheat CS Series Manual de usuario

evoheat

evoheat EVO ULTRA Series Manual de usuario

evoheat

evoheat CS Manual de usuario

evoheat

evoheat EVO MAX Series Manual de usuario

evoheat

evoheat 270 Manual de usuario

evoheat

evoheat Polaris MT 70 Manual de servicio

evoheat

evoheat FORCE Series Manual de usuario

evoheat

evoheat COMMAND-i Manual de usuario

evoheat

evoheat Evo Fusion-i Manual de usuario

evoheat

evoheat EVO FLEX 10 Manual de usuario

evoheat

evoheat Force-i 9 Manual de usuario

evoheat

evoheat EVO FLEX 10 Manual de usuario

evoheat

evoheat Fusion-i 7 Manual de usuario

evoheat

evoheat CS-i Series Manual de usuario

evoheat

evoheat EDGE-i Manual de usuario

evoheat

evoheat EVO FLEX 10 Manual de usuario

evoheat

evoheat Fusion Series Manual de usuario

evoheat

evoheat H8A Guía rápida

evoheat

evoheat Evo Force-i Manual de usuario

evoheat

evoheat Advanced DHP-R Series Manual de usuario

evoheat

evoheat EVO 270 Manual de usuario

Manuales populares de Bomba de calor de otras marcas

MICROWELL

MICROWELL HP 1000 GREEN Manual de usuario

Sanyo

Sanyo SAP120FCH Manual de usuario

Daikin

Daikin EHYHBH05AA Manual de usuario

Panasonic

Panasonic WH-SDF03E3E5 Guía

Bryant

Bryant 544B Manual de usuario

Airxcel

Airxcel 45000 Series Manual

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manual de usuario

Dimplex

Dimplex LI 16I-TUR Guía del usuario

Carrier

Carrier WSHP Open v3 Guía de configuración rápida

TGM

TGM CTV14CN018A Manual de usuario

Carrier

Carrier 38MGQ Series Manual de usuario

Kokido

Kokido K2O K880BX/EU Guía de solución de problemas

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guía rápida

Carrier

Carrier 48EZN Manual de usuario

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Instrucciones de funcionamiento

Ariston

Ariston NIMBUS Manual de usuario

Weishaupt

Weishaupt WWP L 7 Guía del usuario

GE Zoneline AZ85H09EAC Manual de usuario

evoheat Evo Control 17 Manual de usuario

Manuales populares de Bomba de calor de otras marcas