Evoheat Force-i Series Manual de usuario

Page | 1

Page | 2

Contents

1. Preface ...................................................................................................................................................... 3

1.1 Caution & Warnings ............................................................................................................................. 5

2. Unit Dimensions......................................................................................................................................... 6

3. Installation & Connection........................................................................................................................... 7

3.1 Installation Illustration ......................................................................................................................... 7

3.2 Unit Location........................................................................................................................................ 8

3.3 Minimum Clearances............................................................................................................................ 8

3.4 Plumbing.............................................................................................................................................. 9

3.5 Electrical Wiring ..................................................................................................................................10

3.6 Initial Start-up of the Unit....................................................................................................................10

4. Usage and Operation Instructions .............................................................................................................11

4.1 Controller Introduction .......................................................................................................................11

4.2 Controller Functions............................................................................................................................12

4.2.1 Start-up and Shutdown.................................................................................................................12

4.2.2 Mode Switch and Target Temperature Setting..............................................................................12

4.2.3 Clock Setting.................................................................................................................................13

4.2.4 Silent & Silent Timing Setting........................................................................................................15

4.2.5 Fault History.................................................................................................................................17

4.2.6 Colour Display Calibration ............................................................................................................17

4.2.7 Temperature Curve ......................................................................................................................18

4.3 Parameter List and Breakdown Table ..................................................................................................19

4.4 Interface Drawing................................................................................................................................22

5. Maintenance and Inspection .....................................................................................................................25

Appendix ...................................................................................................................................................31

6.1 Cable Specifications.............................................................................................................................31

6.2 Comparison Table of Refrigerant Saturation Temperature...................................................................32

7.Warranty ...................................................................................................................................................33

7.1 Warranty Registration.........................................................................................................................34

Page | 3

1. Preface

To provide our customers with quality, reliability and versatility, this product has been made to strict

production standards. This manual includes all the necessary information about installation, debugging,

discharging and maintenance. Please read this manual carefully before you open or maintain the unit. The

manufacturer of this product will not be held responsible if someone is injured or the unit is damaged as a

result of improper installation, debugging, or unnecessary maintenance. It is vital that the instructions within

this manual are always adhered to. The unit must be installed by qualified personnel.

•The unit can only be repaired by a qualified installer centre, personnel or an authorised dealer.

•Maintenance and operation must be carried out according to the recommended time and frequencies,

as stated in this manual.

•Use genuine standard spare parts only.

•Failure to comply with these recommendations will invalidate the warranty.

The Force-i series has the following characteristics:

Durable

The heat exchanger is made of PVC & Titanium tubing with can withstand prolonged exposure to swimming

pool water.

Installation Flexibility

The unit can be installed outdoors.

Quiet Operation

The unit comprises of an efficient rotary/scroll compressor and a low-noise fan motor which guarantees its

quiet operation.

Advanced Controlling

The unit includes micro-computer controlling, allowing all operation parameters to be set. Operation status

can be displayed on the LCD wire controller/

WARNING

Do not use any means to accelerate the defrosting processor or to clean

other than those recommended by the manufacturer.

The unit must be stored in a room without any continuously operating

ignition sources (for example: open flames, an operating gas appliance or

an operating electric heater.)

Do not pierce or burn.

Be aware that refrigerants may not contain an odour.

NOTE: The manufacturer may provide other suitable examples or may provide additional information about

the refrigerant odour.

Page | 4

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

The appliance shall be installed in accordance with national wiring regulations.

Do not operate your unit in a wet room such as a bathroom or laundry room.

Before obtaining access to terminals, all supply circuits must be disconnected.

An all-pole disconnection device must be incorporated which as at least 3mm clearances in all poles, a

leakage current that may exceed 10mA, residual current device (RCD) having a rated residual operating

current not exceeding 30mA and disconnection must be incorporated in the fixed wiring in accordance with

the wiring rules.

The unit should be installed, operated and stored in a room with a floor area larger than 30m2.

-The installation of pipe-work shall be kept to a minimum 30 m2

-Spaces where refrigerant pipes shall be compliance with national gas regulations.

-Servicing shall be performed only as recommended by the manufacturer.

-The appliance shall be stored in a well-ventilated area where the room size corresponds to the room

area as specified for operation.

-All working procedure that affects safety means shall only be carried by competent persons.

Transport of equipment containing flammable refrigerants

-Compliance with the transport regulations

-Marking of equipment using signs

-Compliance with local regulations

-Disposal of equipment using flammable refrigerants

-Compliance with national regulations

-Storage of equipment/appliances

-The storage of equipment should be in accordance with the manufacturer's instructions. Storage of

packed (unsold) equipment

-Storage package protection should be constructed such that mechanical damage to the equipment

inside the package will not cause a leak of the refrigerant charge.

-The maximum number of pieces of equipment permitted to be stored together will be determined

by local regulations.

Page | 5

1.1 Caution &Warnings

The unit can only berepaired byqualified personnel oranauthorised dealer.

Children should besupervised toensure that they donot play with the appliance.

Please make sure that the unit and power connection have good earthing, otherwise there isa risk of

electrical shock.

Directive 2002/96/EC (WEEE):

The symbol depicting a crossed-outwaste bin that isunderneath the appliance indicates that this product at

the end ofits useful life, must behandled separately from domestic waste, and must betaken to a recycling

centre for electric and electronic devices orhanded back tothe dealer when purchasing anequivalent

appliance.

Directive 2002/95/EC (RoHs): This product iscompliant with directive 2002/95/EC (RoHs) concerning

restrictions forthe use ofharmful substances inelectric and electronic devices.

The unit CANNOT beinstalled near flammable gas. If there isanyleakage of the gas a fire can occur.

Make sure that there iscircuit breaker for the unit, lack of circuit breaker can lead to electrical shock or fire.

The heat pump located inside the unit isequipped with anover-load protection system. Itdoes not allow for

the unit tostart for atleast 3 minutes from a previous stoppage.

The unit can only berepaired bythe qualified personnel of an installer center or an authorized dealer.

Installation must beperformed inaccordance with the NEC/CEC byauthorized person only（for North

America market）

USE SUPPLY WIRES SUITABLE FOR 75℃.

Caution: Single wall heat exchanger, not suitable for potable water connection.

Page | 6

2. Unit Dimensions

Force i9/Force i12 unit: mm

Force i17 unit: mm

Page | 7

3. Installation & Connection

3.1 Installation Illustration

The factory only provides the main unit and the water unit, other items in the illustration above are

necessary spare parts for the water system that are to be provided by the user or the installer.

ATTENTION:

Please follow these steps when using for the first time

1. Open valve and charge water

2. Make sure that the pump and the water-in pipe have been filled with water.

3. Close the valve and start the unit.

NOTE: It is necessary that the water-in pipe is higher than the pool surface.

The schematic diagram is for reference only. Please check the water inlet/outlet label on the heat pump

while plumbing installation.

Page | 8

3.2 Unit Location

Before installation it is very important to

ensure 4 variables are carefully checked to

allow the unit to operate correctly:

• Adequate Air Flow

• Correct water flow volume

• Correct electrical connection & supply

• Heater condition

*For indoor pools please consult the supplier.

DO NOT place the unit in an enclosed area,

where the units discharge air can be re-

circulated.

In an enclosed area take measures to

evacuate the cold waste air out of the room.

Conversely make sure there is adequate air

entering the room to supply the heat pump.

3.3 Minimum Clearances

Evo recommend the heat pump should ONLY be installed in a location with appropriate ventilation. See

above for minimum airflow clearances.

The Evo pool heat pump should be installed with a minimum clearance of at least 3.5m to the water’s edge.

Furthermore, EvoHeat recommend installing the heat pump no greater than 7.5 meters away from the

water’s edge due to heat loss from the piping. If you do not have a location with these suggested clearances,

please contact our EvoHeat Tech Support Specialist on 1300 859 933 to discuss appropriate installation

locations.

The heat pump should be installed a maximum of 5m below the water level of the pool/spa.

Make sure the heat pump is not located where large amounts of water may run-off from a roof into the unit.

Sharp sloping roofs without gutters will allow excessive amounts of rain water mixed with debris from the

roof to be forced through the unit. A water deflector may be needed to protect the heat pump.

If installing the heater on an existing pump/filtration system, the heater must be installed AFTER the filter

and BEFORE the chlorinator/sanitizer.

The heat pump should be installed on a flat level surface.

In the event that a suitable location is unavailable contact Evo Industries for specialist technical advice.

Page | 9

3.4 Plumbing

The Swimming Pool Heat Pumps exclusive rated flow titanium heat exchanger requires no special plumbing

arrangements except bypass (please set the flow rate according to the nameplate).

The water pressure drop is less than 10kPa at max flow rate. Since there is no residual heat or flame

temperatures, the unit does not need copper heat sink piping. PVC pipe can be run straight into the unit.

Location: Connect the unit in the pool pump discharge (return) line downstream of all filter and pool pumps,

and upstream of any chlorinators, ozonators or chemical pumps.

Standard models have slip glue fittings which accept 40mm NB PVC pipe for connection to the pool or spa

filtration piping. By using a 50 NB to 40NB you can plumb 40NB.

Give serious consideration to adding a quick coupler fitting at the unit inlet and outlet to allow easy draining

of unit for winterizing and to provide easier access should servicing be required.

Since the Heat pump cools down the air about 4 -5℃, water may condense on the fins of the horseshoe

shaped evaporator. If the relative humidity is very high, this could be as much as several litres an hour. The

water will run down the fins into the basepan and drain out through the barbed plastic condensation drain

fitting on the side of the basepan. This fitting is designed to accept 20mm clear vinyl tubing which can be

pushed on by hand and run to a suitable drain. It is easy to mistake the condensation for a water leak inside

the unit.

NB: A quick way to verify that the water is condensation is to shut off the unit and keep the pool pump

running. If the water stops running out of the basepan, it is condensation. AN EVEN QUICKER WAY IS TO TEST

THE DRAIN WATER FOR CHLORINE - if the is no chlorine present, then it's condensation.

Page | 10

3.5 Electrical Wiring

NOTE: Although the unit heat exchanger is electrically isolated from the rest of the unit, it simply prevents

the flow of electricity to or from the pool water. Grounding the unit is still required to protect you against

short circuits inside the unit. Bonding is also required.

The unit has a separate molded-in junction box with a standard electrical conduit nipple already in place.

Just remove the screws and the front panel, feed your supply lines in through the conduit nipple and wire-

nut the electric supply wires to the three connections already in the junction box (four connections if three

phase). To complete an electrical hookup, connect the heat pump by electrical conduit, UF cable or other

suitable means as specified (as permitted by local electrical authorities) to a dedicated AC power supply

branch circuit equipped with the proper circuit breaker, disconnect or time delay fuse protection.

Disconnect

A disconnect means (circuit breaker, fused or un-fused switch) should be located within sight of and readily

accessible from the unit, this is common practice on commercial and residential air conditioners and heat

pumps. It prevents remotely-energizing unattended equipment and permits turning off power at the unit

while the unit is being serviced.

3.6 Initial Start-up of the Unit

NOTE: For the unit to heat the pool or spa, the filter pump must be running to circulate water through the

heat exchanger.

Start-up Procedure - After installation is completed, you should follow these steps:

1. Turn on your filter pump. Check for water leaks and verify flow to and from the pool.

2. Turn on the electrical power supply to the unit, then press the key ON/OFF on the wire controller, it

should start in several seconds.

3. After running a few minutes make sure the air leaving the top (side) of the unit is cooler (Between 5-

10 ℃)

4. With the unit operating turn the filter pump off. The unit should also turn off automatically.

5. Allow the unit and pool pump to run 24 hours per day until desired pool water temperature is

reached. When the water-in temperature reaches the desired setting, the unit will slow down for a

period of time, if the temperature is maintained for 45 minutes the unit will turn off. The unit will

now automatically restart (as long as your pool pump is running) when the pool temperature drops

more than 0.2 below set temperature.

Time Delay

The unit is equipped with a 3-minute built-in solid-state restart delay included to protect control circuit

components and to eliminate restart cycling and contactor chatter. This time delay will automatically restart

the unit approximately 3 minutes after each control circuit interruption. Even a brief power interruption will

activate the solid state 3-minute restart delay and prevent the unit from starting until the 5-minute

countdown is completed.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Bomba de calor de evoheat

evoheat

evoheat Evo Force-i Manual de usuario

evoheat

evoheat EVO FLEX 10 Manual de usuario

evoheat

evoheat 270 Manual de usuario

evoheat

evoheat Fusion Series Manual de usuario

evoheat

evoheat Evo315-C Manual de usuario

evoheat

evoheat Evo270-1 Manual de usuario

evoheat

evoheat COMMAND-i Manual de usuario

evoheat

evoheat Evo Flex Manual de usuario

evoheat

evoheat EVO 270 Manual de usuario

evoheat

evoheat DHP20-R Manual de usuario

evoheat

evoheat EVO ULTRA 32 Manual de usuario

evoheat

evoheat EVO 270 Manual de usuario

evoheat

evoheat EVO ULTRA Series Manual de usuario

evoheat

evoheat Force-i 9 Manual de usuario

evoheat

evoheat EDGE-i Manual de usuario

evoheat

evoheat Evo Fusion-i Manual de usuario

evoheat

evoheat Advanced DHP-R Series Manual de usuario

evoheat

evoheat Evo Fusion-i Manual de usuario

evoheat

evoheat Polaris MT 70 Manual de servicio

evoheat

evoheat FORCE Series Manual de usuario

evoheat

evoheat CS-i Series Manual de usuario

evoheat

evoheat Fusion-i 7 Manual de usuario

evoheat

evoheat CS57 Manual de usuario

evoheat

evoheat Evo315-C Manual de usuario

Manuales populares de Bomba de calor de otras marcas

MICROWELL

MICROWELL HP 1000 GREEN Manual de usuario

Sanyo

Sanyo SAP120FCH Manual de usuario

Daikin

Daikin EHYHBH05AA Manual de usuario

Panasonic

Panasonic WH-SDF03E3E5 Guía

Bryant

Bryant 544B Manual de usuario

Airxcel

Airxcel 45000 Series Manual

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manual de usuario

Dimplex

Dimplex LI 16I-TUR Guía del usuario

Carrier

Carrier WSHP Open v3 Guía de configuración rápida

TGM

TGM CTV14CN018A Manual de usuario

Carrier

Carrier 38MGQ Series Manual de usuario

Kokido

Kokido K2O K880BX/EU Guía de solución de problemas

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guía rápida

Carrier

Carrier 48EZN Manual de usuario

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Instrucciones de funcionamiento

Ariston

Ariston NIMBUS Manual de usuario

Weishaupt

Weishaupt WWP L 7 Guía del usuario

GE Zoneline AZ85H09EAC Manual de usuario

evoheat Force-i Series Manual de usuario

Manuales populares de Bomba de calor de otras marcas