Eutelsat Communications Gilat Gemini Manual de usuario

UTELSAT

ETWORKS

RAINING

Gilat Gemini Quick Installation Guide with PC

Ver. 3.0 - 01/09/2017 EUTELSAT System Integration Team

NSTALLATION TOOLS

Antenna Assembly

Connectors & Cables

Antenna Pointing

Smartphone App ‘Eutelsat Finder’ Level

Mast Fixation

Cables F-Connector Cutter Stripper

Mast 4 X M8 Bolts (5cm min.) Driller

3mm L Key 11 mm Spanner 13 mm Spanner

(Included in the Kit) (Included in the Kit)

(2 X 30m included in the Kit) (Included in the Kit)

Compression

Connector

Recommended

45-70 mm

Diameter and

3mm Thickness

Congratulation for your new Gilat terminal for broadband access to Eutelsat Networks!

Before starting the installation verify that you have all the installation parameters provided in

the Contract Form (Azimuth, Elevation, Skew, Location Code, Cluster Code, Polarization) and

Registration Email (Login Username/Passowrd)

GLOSSARY:

Pointing: finding the correct position of the antenna towards the Eutelsat 36C satellite in the

sky in order to receive broadband signals

Line of sight: direction of the antenna to the satellite

Elevation: vertical angle between the pointing direction towards the satellite and the local

horizontal plane

Azimuth: horizontal angle measured in the local horizontal plane in a clockwise direction from

north. it refers to the rotation of the whole antenna to the vertical axis of the pole

Skew: rotation angle of the reflector around its center

Polarization:

the way a radio electric frequency propagates. Eutelsat 36C uses circular

polarisation where electromagnetic waves rotate around the propagation direction either right

(RHCP) or left (LHCP)

Transceiver: 2W Unit at the end of the antenna that converts the signal frequency between the

satellite signal and the modem. Modem and transceiver are connected with 2 coaxial cables

DISCLAIMER: THIS GUIDE IS FOR USE BY TRAINED PROFESSIONALS ONLY. EUTELSAT &

EUTELSAT NETWORKS ARE NOT RESPONSIBLE FOR ANY HARM OR DAMAGE RESULTING FROM

THE USE OF THIS GUIDE

FIGURE

ANTENNA

BOLTS

NUTS

AZIMUTH BOLT (#4)

AZIMUTH NUT (#5)

ELEVATION NUT (#3)

AZIMUTH NUT (#6)

ELEVATION

NUT (#2)

ELEVATION

BOLT (#1)

4 MAST LOCKING

NUTS (#7-10)

FIGURE

TRANSCEIVER

(POLARIZATION

RHCP

LHCP)

INSTALLATION STEPS

POLARIZER

2.1 TRANSCEIVER

POLARIZER

MARKER

2.2 LHCP

2.3 RHCP

LEFT HAND

POLARIZATION

(Tx LHCP)

RIGHT HAND

POLARIZATION

(Tx RHCP)

Fig. 2.1

Fig. 2.2

Fig. 2.3

Step 1: Select installation site following 4 rules:

- Clear line sf sight

- Suitable surface for fixing mast

- Cable route and distance (30m)

- Safety of installation

Step 2: To check Line of sight open the

Android/iOS smartphone App 36 Broadband

Pointer

Step 3: Click on ‘Find Satellite’ and move the

phone until the red circle becomes green (fig. 3)

Step 4: Make sure no obstruction appears within

the green circle (clear line of sight as fig. 3)

Step 5: Identify on the Contract Form the

Polarization value (RHCP or LHCP)

Step 6: Assemble the Transceiver according to

fig. 2.2 if LHCP or fig. 2.3 if RHCP

Step 7: Assemble the Antenna: Reflector, Az/El

Head, Arm, Brakets

Step 8: Install the antenna on the mast and

check with a lever if the mast is vertical

Step 9: Fix the Transceiver on the antenna arm

Step 10: Connect first Coaxial cable between

modem (RF IN) and Transceiver (RX) and connect

second Coaxial cable between modem (RF OUT)

and Transceiver (TX) as fig. 4 (make sure the side

of the cables with the compression connectors

are set outside on the Transceiver). Tighten all 4

connectors with 11mm spanner

Step 11: Connect ground cable to the bracket

Part 2: System Assembly

Part 1: Site Selection

Figure 3

Figure 4

Cable

IN OUT

INSTALLATION STEPS

Part 3: Modem Configuration

Step 12:

nable DHCP on the PC:

- From Start menu select Control Panel , select Network

and Sharing Center, then select Change Adapter Settings

- Double click on the active Local Area Connection

- Click on Properties

- Double click on Internet Protocol Version 4

- Verify ‘Obtain an IP address automatically’ is selected

(fig. 5) and verify ‘Obtain DNS server address

automatically’ is selected (fig. 6)

Step 13: Disable PROXY on the PC:

From Start menu select Control Panel

- Select Internet Option

- Click the Connections tab and select LAN Settings

- Verify that ‘Use a proxy server for your LAN’ is not

selected (fig. 7)

Step 14: Connect the ethernet cable between modem

and PC and plug the modem to the power supply

Step 15: Identify on the Contract Form the Location

Code & RF Cluster Code (fig. 9)

Step 16: Open a browser on the PC and type:

http://sky.manage

Step 17: Load in the modem the RF Cluster Table with

the bin file provided in a CD included in the kit (fig. 8):

- Click on LOAD RF Cluster Table (left bottom corner)

- Browse the files from the CD and select the bin file

45f6c373.bin

- Click on LOAD

- Check ‘Import Succeeded’ message and then Click on OK

Step 18: Enter Location Code & RF Cluster Code on

modem page ‘Step 1/3’, then click

(fig. 9)

Step 19: Click on ‘Start Pointing’ (fig. 10) and then the

Transceiver will start to generate Audio Tones

Figure 5

Figure 6

Figure 7

Figure 10

Figure 9

Figure 8

CONTRACT FORM

Part 4: Antenna Pre-Set

Step 20: Identify on the Contract Form the Elevation

(Ex: 30) and Skew values

Step 21: Check 4 skew nuts are loosen (fig. 11)

Step 22: Rotate the reflector and set the Skew value

using the marker and the scale (fig. 12)

Step 23: Lock off 4 skew nuts (fig. 11)

Step 24: Check 2 Elevation nuts #2 & #3 are loosen

(fig. 1)

Step 25: Put the Elevation Offset Arrow on the

antenna (see fig. 13) and read the Offset value on

the scale below (Ex: -1)

Step 26: Add the Offset value of Step 25 to the

Elevation value of Step 20 (Ex: 30 - 1 = 29)

Step 27: Set Elevation calculated at step 26 with

Elevation Bolt #1 (fig. 1) using the scale and marker

with triangular shape (fig. 13)

Step 28: Check 2 Azimuth nuts #5 & #6 are loosen

(fig. 1)

Step 29: Move Azimuth bolt #4 (fig.1) untill the fine

azimuth scale is 0 and the upper bolt is centered

(fig. 14)

Figure 11

Figure 12

Figure 13

Figure 14

Part 5: Antenna Pointing

Step 30: Scan the Azimuth by slowly swinging the

antenna from left to right and then stop when the

Heartbeat Tone is replaced by a Beep Tone

(interrupted tone), confirmed by a transitioning

melody

Step 31: Fix the Antenna by tightening the 4 locking

nuts #7-10 (fig. 1) on the 2 clamps holding the pole

Step 32: Fine pointing Azimuth (fig. 15):

- Rotate Azimuth bolt #4 (fig. 1) in any direction until the

audio tone drops in tone a first time

Reverse the direction until a continuous tone is achieved

and continue in the same direction until the audio tone

drops a second time

- Reverse the direction again and stop when a 2nd

continuous tone is achieved

Step 33: Fine pointing Elevation (fig. 15):

Repeat the same procedure of Step 32 with the Elevation

bolt #1 (fig. 1) instead of the azimuth bolt

Step 34: Fine pointing Azimuth a 2nd time (fig. 15):

Repeat again Step 32

Step 35: Lock off the 2 azimuth locking nuts #5 & #6

(fig. 1)

Step 36: Lock off the 2 elevation locking nuts #2 & #3

(fig. 1)

Step 37: Check the antenna pointing by gently

pushing and pulling at the top/bottom & left/right

Step 38: Check on the modem page ‘Step 2/3 - Dish

Pointing’ (fig. 16) that the carrier is locked with a

green arrow and verify signal levels

Figure 15

Spanner Rotation

Figure 16

Step 39: Click ‘Finish Pointing’ (fig. 17) to start the

the 5 Steps Synchronization phase

Step 40: During the synchronization no actions

are needed but just verify each step (fig. 18)

Step 41: At the end of the process on the

‘Installation completed Successfully’ dialog box

click on FINISH (fig. 19). The modem home page

containing the system general information is then

displayed

Step 42: Open a new window in your browser

and type the web address:

cabinet.eutelsatnetworks.ru to access the

OSS/BSS page. You can now enter your

credentials (Username/Password) provided in the

registration email you have received (fig. 20).

Then click on ENTER

Step 43: You should now access the Service

Profile Page (fig. 21) to change your service offer:

- Confirm the installation address by clicking YES

- Check the Balance

- Click on CHANGE

- Select your Service Profile (fig. 22)

- Click on CHANGE OFFER if required

Step 44: You can now connect to the internet

using your web browser

Part 6: Modem Activation

Figure 18

Figure 19

Figure 20

Figure 21

Figure 17

Figure 22

Tabla de contenidos

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario