EUROCOM PANTHER 2.0 Guía del usuario

Disassembly

Overview 2 - 1

2.Disassembly

Chapter 2: Disassembly

This chapter provides step-by-step instructions for disassembling the X7200 series notebook’s parts and subsystems.

When it comes to reassembly, reverse the procedures (unless otherwise indicated).

We suggest you completely review any procedure before you take the computer apart.

Procedures such as upgrading/replacing the RAM, optical device and hard disk are included in the User’s Manual but are

repeated here for your convenience.

To make the disassembly process easier each section may have a box in the page margin. Information contained under

the figure # will give a synopsis of the sequence of procedures involved in the disassembly procedure. A box with a

lists the relevant parts you will have after the disassembly process is complete. Note: The parts listed will be for the dis-

assembly procedure listed ONLY, and not any previous disassembly step(s) required. Refer to the part list for the previ-

ous disassembly procedure. The amount of screws you should be left with will be listed here also.

A box with a will also provide any possible helpful information. A box with a contains warnings.

An example of these types of boxes are shown in the sidebar.

Disassembly

2 - 2 Overview

2.Disassembly

NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply (the

battery is removed too).

The following tools are recommended when working on the notebook PC:

Connections within the computer are one of four types:

Locking collar sockets for ribbon connectors To release these connectors, use a small flat-head screwdriver to

gently pry the locking collar away from its base. When replac-

ing the connection, make sure the connector is oriented in the

same way. The pin1 side is usually not indicated.

Pressure sockets for multi-wire connectors To release this connector type, grasp it at its head and gently

rock it from side to side as you pull it out. Do not pull on the

wires themselves. When replacing the connection, do not try to

force it. The socket only fits one way.

Pressure sockets for ribbon connectors To release these connectors, use a small pair of needle-nose pli-

ers to gently lift the connector away from its socket. When re-

placing the connection, make sure the connector is oriented in

the same way. The pin1 side is usually not indicated.

Board-to-board or multi-pin sockets To separate the boards, gently rock them from side to side as

you pull them apart. If the connection is very tight, use a small

flat-head screwdriver - use just enough force to start.

Disassembly

Overview 2 - 3

2.Disassembly

The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a re-

moval and/or replacement job, take the following precautions:

1. Don't drop it. Perform your repairs and/or upgrades on a stable surface. If the computer falls, the case and other

components could be damaged.

2. Don't overheat it. Note the proximity of any heating elements. Keep the computer out of direct sunlight.

3. Avoid interference. Note the proximity of any high capacity transformers, electric motors, and other strong mag-

netic fields. These can hinder proper performance and damage components and/or data. You should also monitor

the position of magnetized tools (i.e. screwdrivers).

4. Keep it dry. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly

damaged.

5. Be careful with power. Avoid accidental shocks, discharges or explosions.

6. Peripherals – Turn off and detach any peripherals.

7. Beware of static discharge. ICs, such as the CPU and main support chips, are vulnerable to static electricity.

Before handling any part in the computer, discharge any static electricity inside the computer. When handling a

printed circuit board, do not use gloves or other materials which allow static electricity buildup. We suggest that

you use an anti-static wrist strap instead.

8. Beware of corrosion. As you perform your job, avoid touching any connector leads. Even the cleanest hands pro-

duce oils which can attract corrosive elements.

9. Keep your work environment clean. Tobacco smoke, dust or other air-born particulate matter is often attracted

to charged surfaces, reducing performance.

10. Keep track of the components. When removing or replacing any part, be careful not to leave small parts, such as

screws, loose inside the computer.

Do not apply cleaner directly to the computer, use a soft clean cloth.

Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Disassembly

Removing the Battery 2 - 5

2.Disassembly

1. Turn the computer off, and turn it over.

2. Loosen screws - (Figure 1a)and carefully lift the battery up (Figure 1b).

3. Remove the battery from the battery bay (Figure 1c).

Figure 1

Battery Removal

Disassembly

2 - 12 Removing the Keyboard

2.Disassembly

1. Turn off the computer and remove the battery (page 2 - 5).

2. Remove screws - from the bottom of the computer (Figure 8a).

3. Turn the computer over, open the Lid/LCD, and carefully (a cable is connected to the underside of the LED cover

module) unsnap up the LED cover module from point on the right (Figure 8b).

4. Disconnect cable and remove the LED cover module (Figure 8c).

Figure 8

Keyboard Removal

Disassembly

Removing the Keyboard 2 - 13

2.Disassembly

5. Remove screws - from the keyboard (Figure 9d).

6. Carefully lift the keyboard up, being careful not to bend the keyboard ribbon cable . Disconnect the keyboard

ribbon cable from the locking collar socket (Figure 9e).

7. Remove the keyboard (Figure 9f).

d. f.

7 8 9

Keyboard Tabs

(f)

Figure 9

Keyboard Removal

(cont’d.)

Disassembly

2 - 14 Removing the Keyboard

2.Disassembly

8. Remove screws - from the keyboard shielding plate (Figure 10g).

9. Lift the keyboard shielding plate up in the direction of the arrow (Figure 10h).

10. Remove the keyboard shielding plate (Figure 10i).

g. h.

Figure 10

Keyboard

Removal (cont’d.)

Disassembly

Removing the Keyboard 2 - 15

2.Disassembly

1. When re-inserting the keyboard shielding plate make sure you insert it by sliding it into position at an angle as

illustrated by arrow below, and press it down into position (Figure 11a).

2. Secure the plate with screws - (Figure 11b).

Figure 11

Keyboard

Shielding Plate

Insertion

a. b.

Disassembly

2 - 18 Removing the System Memory (RAM)

2.Disassembly

The computer has three memory sockets for 204 pin Small Outline Dual In-line Memory Modules (SO-DIMM) support-

ing DDR3 1066/1333MHz. The main memory can be expanded up to 12GB. The SO-DIMM modules supported are

1024MB, and 2048MB and DDRIII Modules. The total memory size is automatically detected by the POST routine once

you turn on your computer.

1. Turn off the computer, remove the battery (page 2 - 5) and the keyboard (page 2 - 9).

2. The RAM modules will be visible at points - (Figure 14a).

3. Gently pull the two release latches ( - )on the sides of the memory socket in the direction indicated by the

arrows (Figure 14b).

4. The RAM module will pop-up (Figure 14c), and you can then remove it.

Figure 14

RAM Module

Removal

Otros manuales de Computadora portátil de EUROCOM

EUROCOM

EUROCOM m248 Manual de usuario

EUROCOM

EUROCOM M375E MILANO Manual de usuario

EUROCOM

EUROCOM Notebook Manual de usuario

EUROCOM

EUROCOM D400V IMPRESSA Manual de usuario

EUROCOM

EUROCOM Sky X4 Manual de usuario

EUROCOM

EUROCOM M120 VOYAGE Manual de usuario

EUROCOM

EUROCOM 5600D Monte Carlo Manual de usuario

EUROCOM

EUROCOM ARMADILLO 2 W840AU Manual de usuario

EUROCOM

EUROCOM Notebook Manual de usuario

EUROCOM

EUROCOM D900T PHANTOM Manual de usuario

EUROCOM

EUROCOM M560A Service Manual de usuario

EUROCOM

EUROCOM D47EV IMPRESSA Manual de usuario

EUROCOM

EUROCOM P5 Pro SE Manual de usuario

EUROCOM

EUROCOM D870P MIRAGE Manual de usuario

EUROCOM

EUROCOM Monster 4 Manual de usuario

EUROCOM

EUROCOM Shark 5 Manual de usuario

EUROCOM

EUROCOM Notebook V12.3.10 Manual de usuario

EUROCOM

EUROCOM M400A COBRA Manual de usuario

EUROCOM

EUROCOM 8500-C DeskNote Manual de usuario

EUROCOM

EUROCOM Notebook V12.1.00 Manual de usuario

EUROCOM

EUROCOM m238 Manual de usuario

EUROCOM

EUROCOM 4200 San Marino Manual de usuario

EUROCOM

EUROCOM 4200 Manual de usuario

EUROCOM

EUROCOM D40EF IMPRESSA Manual de usuario

Manuales populares de Computadora portátil de otras marcas

HP ze2401xt - Pavilion Notebook PC Manual de usuario

Velocity

Velocity NoteMagix M10 Manual de usuario

Dell

Dell Alienware 17 R2 Manual de usuario

Toshiba

Toshiba A105-S2236 Manual de usuario

HP ENVY 17 Manual

Winbook

Winbook LM Manual de usuario

Dell

Dell Inspiron 1464 Manual de usuario

Dell

Dell Inspiron 15R 5537 Manual de usuario

HP PROBOOK 4520S Manual

Dell

Dell Latitude ATG D620 Manual de usuario

Sony

Sony VAIO PCG-FX270 Manual de usuario

Dell

Dell Latitude 7310 Manual de usuario

Dell

Dell Precision GU806 Manual de usuario

Sony

Sony VAIO PCG-R505JLK Manual de usuario

Lenovo

Lenovo THINKPAD X32 Manual de usuario

HP Compaq tc4200 Guía de inicio rápido

Toshiba

Toshiba mini NB300 Manual de usuario

Lenovo

Lenovo ThinkPad X201 Tablet Manual