ETS-Lindgren 4310 Manual de usuario

©ETS-LINDGREN L.P. –DECEMBER 2003 REV A –PN 399280

Model 4310

Shielded Fiber Optic

CCTV System

MANUAL

MODEL 4310 CCTV

REV A –PN 399280

ETS-Lindgren L.P. reserves the right to make changes to any product described herein in order to improve

function, design or for any other reason. Nothing contained herein shall constitute ETS-Lindgren L.P.

assuming any liability whatsoever arising out of the application or use of any product or circuit described

herein. ETS-Lindgren L.P. does not convey any license under its patent rights or the rights of others.

No part of this document may be copied by any means

without written permission from ETS-Lindgren L.P.

E-MAIL & INTERNET

Support@ets-lindgren.com

http://www.ets-lindgren.com

USA

1301 Arrow Point Dr., Cedar Park, TX 78613

P.O. Box 80589, Austin, TX 78708-0589

Phone 512.531.6400

Fax 512.531.6500

FINLAND

Euroshield OY

Mekaanikontie 1

27510, Eura, Finland

Phone + 358.2.838.3300

Fax + 358.2.865.1233

JAPAN

4-2-6, Kohinata

Bunkyo-ku

Tokyo 112-0006

JAPAN

Phone + 81 3 3813 7100

Fax + 81 3 3813 8068

CHINA

1917-1918 Xue Zhixuan Building

No 16 Xue Qing Road

Haidian District

Beijing Postcode: 100083

CHINA

Phone + 86 010 82755304

Fax + 86 010 82755307

MODEL 4310 CCTV

REV A –PN 399280

Table of Contents

INTRODUCTION.........................................................................................................................................................1

SYSTEM OVERVIEW ................................................................................................................................................1

STANDARD CONFIGURATION............................................................................................................................2

STANDARD CONFIGURATION............................................................................................................................3

OPTIONS.........................................................................................................................................................................3

BRIEF DESCRIPTION OF MAJOR ITEMS .......................................................................................................4

SHIELDED CCTV CAMERA ASSEMBLY....................................................................................................................4

VIDEO CONTROL UNIT (VCU)...................................................................................................................................5

MONITOR UNIT.............................................................................................................................................................6

SHIELDED CCTV CAMERA ASSEMBLY POWER SUPPLIES.....................................................................................7

ELECTRICAL CABLE ASSEMBLIES..............................................................................................................................7

FIBER OPTIC CABLE ASSEMBLIES..............................................................................................................................7

PRECAUTIONS ............................................................................................................................................................8

CAMERA .....................................................................................................................................................................8

MONITOR.......................................................................................................................................................................8

INSTALLATION AND SETUP ..............................................................................................................................10

UNPACKING.................................................................................................................................................................10

GOOD SHIELDING PRACTICE....................................................................................................................................10

INSTALLATION INSTRUCTIONS FOR WALL MOUNTED CAMERA SYSTEMS .........................11

INSTALLATION INSTRUCTIONS FOR CEILING MOUNTED CAMERA SYSTEM......................14

INSTALLATION INSTRUCTIONS FOR TRIPOD MOUNTED CAMERA SYSTEM........................18

INSTRUCTIONS FOR IN-CAR CAMERA SYSTEM.....................................................................................19

POWER SUPPLY INSTALLATION ....................................................................................................................20

FILTERED POWER SUPPLY.........................................................................................................................................20

SHIELDED POWER SUPPLY........................................................................................................................................21

SHIELDED BATTERY PACK........................................................................................................................................21

INSTALLING CABLES TO SHIELDED ENCLOSURE...............................................................................22

FEEDING THROUGH SCREEN ENCLOSURE WALL USING A WAVEGUIDE............................................................22

FEEDING THROUGH SCREEN ENCLOSURE WALL USING A BULKHEAD CONNECTOR.......................................23

ELECTRICAL AND OPTICAL CONNECTIONS TO VIDEO CONTROL UNIT (VCU)..................23

OPERATION................................................................................................................................................................25

JOYSTICK (OR FOUR PUSHBUTTONS)........................................................................................................................25

RED PUSHBUTTONS (ZOOM)...................................................................................................................................25

ORANGE PUSHBUTTONS (FOCUS)..........................................................................................................................25

MODEL 4310 CCTV

REV A –PN 399280

YELLOW PUSHBUTTONS (IRIS)................................................................................................................................25

ADJUSTING THE PAN AND TILT LIMIT SWITCHES..............................................................................26

HORIZONTAL AXIS (PAN ANGLE)..............................................................................................................................26

VERTICAL AXIS (TILT ANGLE)..................................................................................................................................26

CHARGING THE SHIELDED BATTERY PACK...........................................................................................27

SPECIFICATIONS.....................................................................................................................................................28

SHIELDED CCTV CAMERA ASSEMBLY..................................................................................................................28

CAMERA.......................................................................................................................................................................28

LENS.............................................................................................................................................................................28

CONNECTORSTO CAMERAASSEMBLY...................................................................................................................28

PAN AND TILT HEAD..................................................................................................................................................28

VIDEO CONTROL UNIT..............................................................................................................................................29

WARRANTY................................................................................................................................................................30

MODEL 4310 CCTV

REV A –PN 399280

SAFETY SYMBOL DEFINITIONS

REFER TO MANUAL

When product is marked with this symbol refer to instruction manual for

additional information.

HIGH VOLTAGE

Indicates the presence of hazardous voltage. Unsafe practices could

result in severe personal injury or death.

PROTECTIVE EARTH GROUND (SAFETY GROUND)

Indicates protective earth terminal. You should provide an uninterruptible

safety earth ground from the main power source to the product input

wiring terminals, power cord, or supplied power cord set.

CAUTION

Denotes a hazard. Failure to follow instructions could result in minor

personal injury and/or property damage. Included text gives proper

procedures.

GENERAL SAFETY CONSIDERATIONS

BEFORE POWER IS APPLIED TO THIS INSTRUMENT, GROUND IT

PROPERLYthrough the protective conductor of the AC power cable to a

power source provided with protective earth contact. Any interruption of

the protective (grounding) conductor, inside or outside the instrument, or

disconnection of the protective earth terminal could result in personal

injury.

BEFORE SERVICING: CONTACT ETS-LINDGREN–servicing (or

modifying) the unit by yourself may void your warranty. If you attempt to

service the unity by yourself, disconnect all electrical power before

starting. There are voltages at many points in the instrument which

could, if contacted cause personal injury. Only trained service personnel

should perform adjustments and/or service procedures upon this

instrument. Capacitors inside this instrument may still be CHARGED

even when the instrument is disconnected from its power source.

FUSE

2A:250

TO AVOID A SAFETY HAZARD, replace fuses with the same current

rating and type (normal blow, time delay, etc.). Order any replacement

parts direct from ETS-Lindgren.

ONLY QUALIFIED PERSONEL should operate (or service) this

equipment.

STOP IN EVENT OF EMERGENCYpower unit down.

CAUTION

WARRANTY

MODEL 4310 CCTV

REV A –PN 399280

MODEL 4310 CCTV Introduction

REV A –PN 399280

INTRODUCTION

The ETS-Lindgren Model 4310 CCTV is ideal for monitoring or

witnessing tests conducted in anechoic or reverb chambers and large

test cells where high EMI field strengths are present. The camera’s

shielded case allows it to operate in fields exceeding 200 V/m. Pan, tilt

and zoom functions allow monitoring of a wide area of interest, or

zooming in close for details. Images are transmitted over fiber optic lines.

This manual provides an overview of the system, installation guidelines

for multiple configurations and an operational guide.

SYSTEM OVERVIEW

This overview of the system is based on the schematic diagram on the

following page.

All control of the system is from the Video Control Unit (VCU). Six

pushbuttons control the camera lens (zoom, focus and Iris), and a

joystick (or four pushbuttons) controls the pan and tilt of the Shielded

CCTV Camera Assembly. A multiplexer printed circuit board (PCB)

combines all the control functions into a single data stream for

transmission over the fiber optic link to the camera assembly.

An interface PCB inside the camera assembly converts the optical

signals to electrical signals to operate the camera and Pan and Tilt

Head. Conversely, the PCB converts the camera’s electrical video

signals to optical signals which are applied via another fiber optic cable

to the VCU. A video receiver PCB in the VCU reconverts the optical

signals back to a standard 1.0 V pk-pk composite video signal for

application to the Monitor and/or a Video Cassette Recorder (VCR). If

the VCU is fitted with a universal serial buss (USB) port, the composite

video signal can also be applied to a Computer.

Standard Configuration MODEL 4310 CCTV

2© ETS-LINDGREN L.P. –DECEMBER 2003

REV A –PN 399280

MONITORVCR

POWERIN

COMPUTER

USEDIFAUSBIS

FITTEDTOTHE

VIDEOCONTROLUNIT

VIDEO

POWERIN

VIDEOCONTROLUNIT

POWERSUPPLIES

(TWOTYPES)

BATTERYPACK

PAN&TILT

HEAD

SHIELDEDCCTVCAME

CONTROLS

LENSCONTROL

(ZOOM,FOCUS,IRIS)

EMCSHIELDEDBOX

SHI

VIDEO

CONTROL

PCB

POWERIN12V

12V

POWERSUPPLYOPTIONSMOUNT(SEE NOTE)

PAN &TILT

CONTROLS

VIDEO

MODEL 4310 CCTV Standard Configuration

REV A –PN 399280

STANDARD CONFIGURATION

•Color Camera, 200 V/m, fitted with 6:1 zoom lense

•Pan and Tilt Head (standard duty)

•Video Control Unit –for pan, tilt, zoom, focus and aperture

functions (single camera) 110 or 240 VAC

•Color Monitor –35.5 cm (14 in) 120/240 VAC

•Fiber Optic Cable –32 m

•Filtered Power Supply –Specify 120 or 240 VAC

•Wall Mount Bracket

PAL OR NTSC should be specified at time of order.

OPTIONS

•10:1 Zoom Lens

•Shielding up to 100 V/m

•Heavy Duty Pan and Tilt Head -for cameras that are to be

covered with ferrite tile

•USB Interface

•Multi-Camera Controller

•Battery Power Supply, Charger and Cables

•Fiber Optic Waveguide Penetration (will need with battery pack)

•Additional Fiber Optic Cable

•Larger and Higher Resolution Monitors

•Non-Metallic Tripod

•Non-Metallic Wall or Ceiling Mount

•Drivers Seat Bracket

•Waveguide Assembly –for individual cables or duplex cables

•ST Bulkhead Connectors –for wall penetration services panel

•On Site Installation

Brief Description of Major Items MODEL 4310 CCTV

REV A –PN 399280

WARRANTY

BRIEF DESCRIPTION OF MAJOR

ITEMS

The actual items and fittings supplied for the CCTV system will depend

upon the requirements of the system as defined when ordering. For

example there is a choice of two zoom lenses for the camera; there are

two versions of the camera assembly casing depending on the strength

of the electrical field that the camera will be used in; and the mounting

items supplied for the camera assembly and its pan and tilt head will

depend upon whether they are to be mounted on a non-metallic tripod,

on a wall or suspended from a ceiling. A range of ceiling mounting

columns and wall brackets are available and are specified according to

whether the chamber has anechoic absorber and where the absorber is

used according to the size specified. Three power supply options for the

camera assembly and its pan and tilt head are available to accommodate

any requirement.

The Monitor and VCU each contain their own power supply circuit (the

operating voltage must be specified when ordering) and are supplied

with power cables. A monitor other than the standard 14-inch color

monitor can also be specified when ordering.

SHIELDED CCTV CAMERA ASSEMBLY

CAUTION The Shielded CCTV Camera Assembly must not be opened.

To do so could compromise the shielding properties of the box and will

invalidate the warranty. Neither the camera nor the interface PCB inside

the box are user serviceable items.

The camera assembly is an EMC shielded steel case containing the

camera and an interface PCB. The lens window in the front of the case is

also shielded with a special metallic coating. To ensure that the shielding

properties of the assembly are maintained, an EMC shielding gasket is

fitted between the rear panel and the main casing. Two versions of the

assembly are available for use in field strengths of 100 V/m and 200

V/m.

Tabla de contenidos

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario