ETC DataTrack Manual técnico

Part Number: 7066M2100 Rev: D

Released: 2019-07

DataTrack and

DataTrack Backbone System

Planning and Installation Manual

To view a list of ETC trademarks and patents, go to

etcconnect.com/ip

All other trademarks, both

marked and not marked, are the property of their respective owners.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents i

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 1

About DataTrack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

About DataTrack Backbone . . . . . . . . . . . . . . . . . . . . . .1

Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Load Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . .2

General Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Help from ETC Technical Services . . . . . . . . . . . . . . . . .4

Chapter 1

Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Planning the Track Layout . . . . . . . . . . . . . . . . . . . . . . .5

Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . .5

Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Ground Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Suspended Load Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

DMX Data Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Chapter 2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . 13

Cutting Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Installation Methods . . . . . . . . . . . . . . . . . . . . . . . . . .14

Surface Mounting (DataTrack Only) . . . . . . . . . . . . . . . . . . . .14

Suspension Mounting (DataTrack only) . . . . . . . . . . . . . . . . .15

Threaded Rod Mounting (DataTrack Backbone) . . . . . . . . . .15

End of Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Installing End Feeds . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Installing Mid Feeds . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Installing Current Limiters (DataTrack only) . . . . . . . .23

Installing Current Limiting Feed Connector on a J-Box . . . . .24

Installing Current Limiting Feed Connector Using

Flexible or Rigid Conduit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Wiring End Feeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Wiring In-line Feeds . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Powering On the Track . . . . . . . . . . . . . . . . . . . . . . . .27

ii DataTrack/DataTrack Backbone System Planning and Installation Manual

Chapter 3

Troubleshooting . . . . . . . . . . . . . . . . . . . . 28

Loss of Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Data Issues. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Appendix A

Parts and Accessories. . . . . . . . . . . . . . . . . 31

Two-circuit Accessories. . . . . . . . . . . . . . . . . . . . . . . . .31

DataTrack Mounting Accessories. . . . . . . . . . . . . . . . .42

Current Limiters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

DataTrack Backbone Accessories . . . . . . . . . . . . . . . . .48

Appendix B

Reconfiguring DMX Data Lines . . . . . . . . 61

Introduction 1

Introduction

About DataTrack

The DataTrack System from ETC is a professional-grade track system that offers built-in

DMX/RDM wiring and two separate power circuits that can be independently switched or

dimmed. DataTrack can be used for hybrid systems using both conventional and LED fixtures.

DataTrack easily blends into its surroundings, providing power and data reliably and

discretely. It's the solution for a variety of permanent applications, including art galleries,

museums, retail displays, lobbies, comedy clubs, nightclubs, and venues with low ceilings or

the need to feed power and data to track-mounted luminaires.

The DataTrack System includes an extensive selection of adapters, feeds, end caps, couplers,

hanging accessories, and other accessories to fit most any installation requirements.

DataTrack offers:

• Two-circuit track with separate neutrals

• Up to 32 DMX devices per data run

• Up to 20 RDM devices per data run

• Suspended or surface mounting (recessed mounting also available; contact your local ETC

representative for more information)

• 3-amp, 5-amp, 8-amp, and 12-amp current-limiting breakers located directly at the track

• Up to 22 pounds per foot (30 kilograms per meter) of load capacity when properly supported

• Two-year warranty

• White, black powder-coated, and silver anodized finishes

• 4 ft, 8 ft, and 12 ft (1.21 m, 2.43 m, and 3.65 m) sections that can be field-cut to custom lengths

as required

• Easy surface mounting using pre-punched holes positioned every 8 in (20.32 cm) in the track

(self-tapping screws can be used in places where there are no pre-punched holes)

About DataTrack Backbone

DataTrack Backbone provides a robust track solution when larger fixtures are required. With

DataTrack Backbone, an aluminum housing encloses DataTrack system hardware, providing

additional strength and more robust structural attachment. A steel fixture hanger combined

with a pigtail adapter allows you to use larger, theatrical lighting fixtures in addition to

traditional track fixtures with DataTrack.

In addition to the DataTrack features described above, DataTrack Backbone offers:

• Suspended mounting

• Increased maximum suspension point distance to 10 ft (3 m)

• Increased load capacity to 250 lb (127 kg) over 10 ft (3 m); see

Suspended Load Capacity

page 8

for load capacity details

• White powder-coated, black anodized, and silver anodized finishes

2 DataTrack/DataTrack Backbone System Planning and Installation Manual

Data

DataTrack and DataTrack Backbone provide integrated wiring for DMX-512A (ANSI E.1.11)

and bidirectional RDM (ANSI E1.20-2010) control signals. The electrical specifications of these

DMX512A and RDM standards are based on ANSI/TIA/EIA-485-A-1998.

DMX512A standards require a continuous daisy-chain data-link topology with a terminating

switch or resistor with a value of 100–120 ohms to eliminate ringing and signal reflection. No

"Tees" or "Stars" are permitted.

Wire used for bringing the DMX signal into the track system must be Belden 9729 or

equivalent with shield connected to ground at one end, preferably the signal source.

Load Capacity

DataTrack and DataTrack Backbone distribute one or two 120V circuits (230V for EUTRAC®

systems), up to 16A on a 20A circuit. Each circuit has an independent neutral for individual

control and a common ground.

• Maximum Feed: 2 x 20A branch circuits

• Maximum Load: 2 x 16A (2 x 1920W at 120V)

• Maximum Load for EUTRAC systems: 2 x 16A (2 x 4600W at 230V)

• Supply Wiring: 12 AWG (2.5 mm2) feed wires

The DataTrack Backbone fixture adapter has a load capacity of 300W (120V supply), or 600W

(230V supply) for EUTRAC systems.

Document Conventions

This document uses the following conventions to draw your attention to important

information.

Please email comments about this manual to: [email protected]

Note:

Notes are helpful hints and information that is supplemental to the main text.

CAUTION:

A Caution statement indicates situations where there may be undefined or

unwanted consequences of an action, potential for data loss or an equipment

problem.

WARNING: A Warning statement indicates situations where damage may occur, people

may be harmed, or there are serious or dangerous consequences of an action.

WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates situations where

there is a risk of electric shock.

Introduction 3

General Warnings

Read and save these instructions before installing ETC DataTrack, and refer to them when

making additions to or changes in the DataTrack configuration.

WARNING: Mains voltage must be switched off before installation or maintenance of

track or track components.

WARNING: • Per NEC article 410.151(C), do not install any part of this track system less

than 5 ft (1.5 m) above the floor.

• Never mount the DataTrack system on a wall. Wall-mount installation is not

supported.

• Follow fixture manufacturer guidelines to keep fixtures away from curtains

or similar combustible materials

• Always disconnect electrical power before adding to or changing the

configuration of the track.

• Only install lighting track fixtures and fittings in DataTrack.

• Per NEC article 410.151(A), lighting track fittings shall not be equipped with

general purpose receptacles. Do not attempt to connect power tools,

extension cords, appliances, or similar devices to the track.

CAUTION:

• For indoor use only. Do not use in wet or damp locations.

• Do not install track where concealed or extended through walls or

partitions.

• Unauthorized modification of DataTrack or DataTrack components may

void ETC warranty.

• Material used for ceiling mounting must conform to building regulations.

Note:

Do not slide track adapters when moving fixtures. Fixtures should be fully removed

from the track, relocated, and then properly re-attached.

4 DataTrack/DataTrack Backbone System Planning and Installation Manual

Help from ETC Technical Services

This manual will guide you through the planning, installation, operation, and troubleshooting

of a DataTrack system.

If you are having difficulties, your most convenient resources are the references given in this

user manual. To search more widely, try the ETC website at etcconnect.com. If none of these

resources are sufficient, contact ETC Technical Services directly at one of the offices identified

below. Emergency service is available from all ETC offices outside of normal business hours.

When calling for support, please try to have the following information available:

• Product model

• Other components in your system (luminaires connected, control source, etc.)

Americas United Kingdom

ETC, Inc. ETC Ltd

Technical Services Department Technical Services Department

3031 Pleasant View Road 26-28 Victoria Industrial Estate

Middleton, WI 53562 Victoria Road,

800-775-4382 (USA, toll-free) London W3 6UU England

+1-608 831-4116 +44 (0)20 8896 1000

[email protected] [email protected]

Asia Germany

ETC Asia ETC GmbH

Technical Services Department Technical Services Department

Room 1801, 18/F Ohmstrasse 3

Tower 1, Phase 1 Enterprise Square 83607 Holzkirchen, Germany

9 Sheung Yuet Road +49 (80 24) 47 00-0

Kowloon Bay, Kowloon, Hong Kong [email protected]

+852 2799 1220

[email protected]

Planning 5

Chapter 1

Planning

Planning the Track Layout

Consider the following elements as you plan your DataTrack or DataTrack Backbone track layout:

•Track orientation: Each piece of track has a top and a bottom.

•Conduit entry points: Each piece has limited available conduit knockouts.

•Data paths and termination locations: Plan the DMX data paths before installation. DMX data

paths must be contiguous daisy chains with terminations. Stars, loops, or Y’s will result in faulty

performance of DMX fixtures.

•Coupler and Track Connections: Couplers will only fit into track in one orientation. The

ground/data bus connection of the coupler must mate with the ground/data bus portion of the

track. This is important to keep in mind when purchasing couplers (ground left versus ground

right, ground inside versus ground outside). All product references to ground orientation also

refer to data bus orientation, as illustrated below.

See

Parts and Accessories

page 31

for a list of available DataTrack and DataTrack Backbone parts.

Figure 1: Coupler and track connections

Planning the Installation

Consider the following elements as you plan your DataTrack or DataTrack Backbone installation:

•

Electrical Requirements

•

Ground Path

•

Suspended Load Capacity

•

DMX Data Path

Electrical Requirements

• Maximum Feed: 2 x 20A branch circuits

• Maximum Load: 2 x 1920W (1.92kW)

• Supply Wiring: 12 AWG (2.5 mm2) feed wires

CAUTION:

Electrical installation must be performed by a qualified electrician in

accordance with local electrical codes and permitting procedures.

Track for

nesting plate

Data

bus

Ground

path

6 DataTrack/DataTrack Backbone System Planning and Installation Manual

Ground Path

The ground path must be continuous with no interruptions. A ground path can cross itself any number

of times. Continuity is the sole concern in planning a DataTrack or DataTrack Backbone ground path.

The following illustrations show examples of ground paths. These drawings are plan views, showing

the track system as if you were looking at it from above.

Figure 2: Simple ground path system

Figure 3: Advanced ground path system

Note:

There are a variety of configurations that can be assembled using the available

couplers. However, couplers only fit into track in one orientation. The data

connection of the coupler must mate with the data connection of the track. This is

important to keep in mind when choosing couplers (ground left versus ground right,

ground inside versus ground outside).

CAUTION:

These figures show a continuous ground path within the track system. If any

of the couplers shown in these examples were replaced with an outside

ground model, the ground path would be broken and the track would not be

properly grounded (and the couplers would not fit within the track).

Ground Path

L-coupler

ground inside

L-coupler

ground inside

L-coupler

ground inside

ground coupler

location track

L-coupler

ground inside

Key:

Ground Path

L-coupler

ground inside

L-coupler

ground inside

L-coupler

ground inside

L-coupler

ground inside

T-coupler

ground inside, left

T-coupler

ground inside, left

T-coupler

ground inside, right

T-coupler

ground inside, right

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Luminaria de ETC

ETC

ETC HIGH END SYSTEMS SolaFrame Theatre Manual de usuario

ETC

ETC Desire series Manual de usuario

ETC

ETC Desire D40 Manual de usuario

ETC

ETC Source Four Revolution Manual de usuario

ETC

ETC Desire D22 Manual de usuario

ETC

ETC Source Four Zoom Manual de usuario

ETC

ETC Desire D22 Manual de usuario

ETC

ETC Source 4WRD Manual de usuario

ETC

ETC High End Systems SolaPix 7 Manual de usuario

ETC

ETC HIGH END SYSTEMS SolaPix 37 Manual de usuario

ETC

ETC ColorSource PAR Pearl Manual de usuario

ETC

ETC ColorSource CYC v1.7 Manual de usuario

ETC

ETC Source Four Revolution Manual de usuario

ETC

ETC ColorSource Linear Manual de usuario

ETC

ETC Irideon FPZ Manual de usuario

Manuales populares de Luminaria de otras marcas

Emos

Emos CLASSIC ZY1431T Manual de usuario

Westinghouse

Westinghouse Outdoor Lighting Fixture Manual de usuario

Hedler

Hedler C 12 silent Manual de usuario

Blizzard Lighting

Blizzard Lighting Puck: CSI Manual de usuario

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manual de usuario

Lightmaxx

Lightmaxx Shaft 5R Manual de usuario

Triarch

Triarch 31083 Manual de usuario

Philips

Philips 32614 Series Manual de usuario

IKEA

IKEA TIVED Manual de usuario

Lightolier

Lightolier LP200 Manual de usuario

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manual de usuario

Martin

Martin MAC 250 Krypton Manual de usuario

Cooper Lighting

Cooper Lighting Halo L3232E Manual de usuario

Stageline

Stageline ODW-2410RGBW Manual de usuario

Light Sky

Light Sky Tornado Series Manual de usuario

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manual de usuario

Lightolier

Lightolier Lytespan 83ED17S Manual de usuario

Lightolier

Lightolier Calculite CS8226 Manual de usuario