ETC ColorSource Linear Manual de usuario

ETC Installation Guide

ColorSource®Linear v1.5

Corporate Headquarters



Middleton, Wisconsin, USA



Tel +608 831 4116

Service (Americas)



[email protected]

London, UK



Tel +44 (0)20 8896 1000



Service: (UK) [email protected]

Rome, IT



Tel +39 (06) 32 111 683



Service: (UK) [email protected]

Holzkirchen, DE



Tel +49 (80 24) 47 00-0



Service: (DE) [email protected]

Hong Kong



Tel +852 2799 1220



Service: (Asia) [email protected]

Web: etcconnect.com



Product information and

specifications subject to change.



ETC intends this document to be provided in its entirety.

7414M2100-1.5



Rev A



Released 2017-01

Overview

The ColorSource Linear is an affordable LED fixture that uses the RGB-L (red,

green, blue, and lime) color system to provide a rich, bright light. The fixture

is available in three lengths:

• ColorSource Linear 1 (0.5 meter)

• ColorSource Linear 2 (1 meter)

• ColorSource Linear 4 (2 meter)

All models are available in both original and Deep Blue variants. For more

information on the differences between these two variants, see the ETC

website at etcconnect.com.

CAUTION:

• Risk of eye injury. Do not stare directly into the light.

• Do not operate in proximity to flammable materials.

Note:

Features described in this document require the latest

version of software. For information on updating fixture

software, see Updating the fixture software on page 13.

ColorSource Linear 1

ETC Installation Guide

ColorSource Linear v1.5

ColorSource Linear v1.5 Page 2 of 16 ETC

Environment

The ColorSource Linear operates in ambient temperatures of 0°C–40°C and

comes with a variable-speed fan.

Electrical

• Operates between 100V and 240VAC at a frequency of 50/60Hz.

• Maximum power consumption:

- Linear 1: 120W

- Linear 2: 240W

- Linear 4: 480W

• Maximum number of fixtures to be linked via power thru connector

when used with an R20 relay module or Unison Echo®Relay Panel:

- Linear 1: 9 luminaires (10 luminaires total per circuit)

- Linear 2: 7 luminaires (8 luminaires total per circuit)

- Linear 4: 3 luminaires (4 luminaires total per circuit)

Consult breaker trip curves when used with other equipment.

Requires power from a non-dimmable source.

Note:

The ColorSource Linear is for indoor use only.

Note:

• Maximum recommended ambient operating

temperature: Ta = 40°C (104°F)

• Maximum anticipated external surface temperature

at 40°C ambient: Tmax = 80°C (176°F)

• External temperatures after 5 minutes of full-

brightness operation at 25°C (77°F) ambient:

36°C (97°F)

• External temperature (steady state achieved) at

25°C (77°F): 48°C (118°F)

WARNING:

Disconnect the fixture from power and DMX and allow

it to cool before performing any cleaning and

maintenance.

ETC Installation Guide

ColorSource Linear v1.5

ColorSource Linear v1.5 Page 3 of 16 ETC

Typical power consumption

Accessories

You can use several half-meter optional accessories with ColorSource Linear

fixtures, including:

• Secondary lenses (horizontal, vertical, and round)

• Barn doors (7414K1020)

• Louver (7414K1019)

For information on installing secondary lenses, see

Installing secondary lenses

page 14

Accessories for Linear 2 and Linear 4

For the Linear 2 and Linear 4 fixtures, order one accessory for each 0.5 meter

segment (cell) of the fixture. For example, for a Linear 2 fixture, order two

barn door accessory kits to fit the full length of the fixture.

Spacers for secondary lenses are included with the fixture. Use these spacers

to hold the accessories in position when multiple lenses are used in the

Linear 2 and Linear 4 fixtures. The spacers are positioned between the

0.5 meter lenses.

Contact your local dealer for more information.

Linear 1 100V 120V 230V

Idle Power/Current

1.63W/0.03A 1.55W/0.03A 1.43W/0.03A

Direct at Full/Current

107W/1.07A 105W/0.88A 104W/0.46A

Linear 2 100V 120V 230V

Idle Power/Current

2.86W/.06A 2.98W/.06A 2.56W/.06A

Direct at Full/Current

210.83W/2.12A 208.67W/1.75A 204.5W/.91A

Linear 4 100V 120V 230V

Idle Power/Current

5.28W/.11A 5.24W/.11A 4.65W/.12A

Direct at Full/Current

424.17W/4.27A 419.33W/3.52A 409.17W/1.82A

ETC Installation Guide

ColorSource Linear v1.5

ColorSource Linear v1.5 Page 4 of 16 ETC

Installation

Mounting

The ColorSource Linear ships with a pair of floor trunnions for mounting.

You also have the option of using C-clamps with the trunnions to hang the

fixture. Attach the C-clamps to the holes in the trunnion feet (see figure

below).

The ColorSource Linear 1 has two additional mounting options. Contact your

local dealer for more information.

• Yoke with C-clamp (7414K1017)

• Double yoke with C-clamp for mounting two fixtures (7414K1018)

Safety cable

The safety cable (or other approved

safety device) must be attached to the

fixture. Two safety cable anchor

points are provided on the fixture

housing.

The anchor points also include two

cutouts that can be used for cable

strain relief.

Connectors

•Power: Two powerCON

connectors for power in and

thru

•Data (DMX512/RDM): Two

five-pin XLR connectors

two RJ45 connectors for data in and thru

Conversion cables are available from ETC. Please contact your ETC customer

service representative and request part number W6538 for RJ45 to female

XLR or part number W6539 for RJ45 to male XLR.

Connector locations

•Linear 1: Power connectors on one side of the fixture and data

connectors on the other

•Linear 2 and Linear 4: Power and data connectors on each end (to

facilitate daisy-chaining)

Note:

Ensure that the trunnions are installed with the feet

inward so that fixtures can be lined up end-to-end, if

needed.

Safety cable

anchor point

C-clamp

attachment

point

Cutout for

cable strain relief

ETC Installation Guide

ColorSource Linear v1.5

ColorSource Linear v1.5 Page 5 of 16 ETC

Setting up the fixture

See the fixture illustrations below and on the following page for reference.

1: Plug power cord into the powerCON In connector on the rear of the

fixture.

2: Make any power-thru cable connections prior to applying a power

source.

3: Plug power cord into power source.

Note:

This fixture is not Ethernet/data network compatible.

Note:

The ColorSource Linear is not self terminating. You must

terminate the last fixture in line with a 120 ohm resistor.

XLR terminators are not available from ETC.

To purchase an RJ45 terminator, please contact your ETC

customer service representative and request part

number N4086.

Data in

and thru

connectors

User interface

(display)

Power in

and thru

connectors

Mode button

Up and

Down

buttons

Trunnion

locking

knob

Trunnion

locking knob

Linear 1

Mode button

ETC Installation Guide

ColorSource Linear v1.5

ColorSource Linear v1.5 Page 6 of 16 ETC

Powering up

1: Press the Mode button once to wake the display. The display shows

the DMX address.

2: Press the Mode button a second time to access the Presets/Sequences

menu.

Adjusting the tilt

The fixture can be tilted up and down as needed.

1: Loosen, but do not remove the two trunnion locking knobs.

2: Tilt the fixture to the desired angle.

3: Tighten the trunnion locking knobs.

User interface

The user interface allows you to set the start

address of the fixture, access the stand-alone

presets and sequences, set the DMX control

mode, and set the Grouping mode (Linear 2 and

Linear 4 fixtures only).

• The DMX address will blink when no DMX

is present and a preset or sequence is not

active. The inactivity time-out is disabled

while in a data loss state.

• After 5 seconds of inactivity when DMX is

present, the display goes dark.

Power and data

connectors are

paired on each

side to facilitate

daisy-chaining

Up and Down

buttons

User interface

(display)

Mode button

Grouping button

and LED indicators

Linear 2 and Linear 4

Linear 1

shown

ETC Installation Guide

ColorSource Linear v1.5

ColorSource Linear v1.5 Page 7 of 16 ETC

Mode button

Pressing the Mode button activates the Preset/Sequence menu; the last active

preset or sequence plays automatically. Pressing the Mode button a second

time deactivates the selected preset or sequence. The display will revert to

show the DMX start address.

• If DMX data is present, the current preset or sequence plays in the

background and DMX data continues to take priority.

• If DMX data is lost and a preset is active in the background, the last

selected preset or sequence automatically plays.

Setting the DMX address

1: Press the Mode button until the DMX address is displayed.

2: Use the Up and Down buttons to select the DMX address for the

fixture.

You can also use RDM for DMX addressing. See

Using RDM

page 16

Setting presets and sequences

There are twelve factory-configured presets followed by five factory-

configured sequences built into the fixture. From the Preset/Sequence menu,

press the Up and Down buttons to scroll through the list. The sequence or

preset plays immediately upon selection. All presets and sequences can be re-

recorded through an RDM device.

When a Linear 2 or Linear 4 fixture is in Cell mode, you can re-record a preset

with each cell having a distinct set of values. See

Setting the Grouping mode

page 9

Re-recording a preset

1: Using DMX or RDM, set the desired levels.

2: Press the Mode button to access the Preset/Sequence menu.

3: Using the Up and Down buttons, navigate to the preset number that

you want to re-record.

4: Hold the Mode button for 3 seconds to confirm the preset selection.

The user interface will show a 3-second countdown. The preset

number blinks once to confirm that the preset has been recorded.

Note:

When the fixture is in Direct mode (



) or 1-channel

mode (



), you cannot re-record presets.

When you re-record presets with the fixture in RGB

mode (



), the intensity is set to full and the strobe is

turned off.

See Changing the DMX control mode on page 9.

ETC Installation Guide

ColorSource Linear v1.5

ColorSource Linear v1.5 Page 8 of 16 ETC

It is possible to activate a known preset or sequence from a connected fixture

when DMX is not present. If a connected fixture activates a preset or

sequence that is not recognized by the Linear fixture, the Linear fixture will

hold its last look. When DMX is restored, the DMX takes priority.

Pre-configured presets

Pre-configured sequences

Adjusting the intensity of presets

1: Ensure that DMX data is not present.

2: Press the Mode button to access the Preset/Sequence menu, and then

press the Up and Down buttons to select the preset that you want to

edit.

3: Hold the Mode button for 3 seconds. The display shows : ## where

the number is an intensity level from , or .

4: Press the Up and Down buttons to change the intensity level of the

preset in real time.

5: Press the Mode button to confirm your selection and return to the

Preset/Sequence menu.

The display will automatically return to the Preset/Sequence menu after

10 seconds of inactivity, and edits to the preset intensity will not be saved.

Preset Name Preset Name

1 3200K White 7 Magenta

2 5600K White 8 Yellow

3 Red 9 Orange

4 Green 10 Light Yellow

5 Blue 11 Light Blue

6 Cyan 12 Light Pink

Sequence Name

1 Rainbow Fast

2 Rainbow Slow

3 Warm Colors Fast

4 Cool Colors Fast

5 Random

ETC Installation Guide

ColorSource Linear v1.5

ColorSource Linear v1.5 Page 9 of 16 ETC

Changing the DMX control mode

You can set the DMX control mode for the fixture to one of four available

mode options.

1: Press the Mode button until the DMX address is displayed.

2: Hold the Mode button for 3 seconds. The display shows the current

DMX control mode.

3: Press the Up and Down buttons to change the DMX control mode.

•: 5-channel mode (intensity, red, green, blue, and strobe)

•: Direct emitter control (intensity, red, green, blue, lime, and

strobe)

•: 1-channel mode controls the intensity of preset 1 (defaults to

3200K White)

•: RGB mode (red, green, and blue)

4: Press the Mode button to confirm your selection.

The display will automatically return to the DMX address after 10 seconds of

inactivity, and edits to the DMX control mode will not be saved. This cancels

unsaved changes.

Setting the Grouping mode

The ColorSource Linear 2 and the

ColorSource Linear 4 fixtures have

two Grouping modes:

•Group: Entire array functions as

a single fixture.

•Cell: Each 0.5 m segment (or

“cell”) of the array functions as

a distinct fixture with a

separate DMX start address.

To set the Grouping mode, press the

Grouping button until the LED

indicator for the chosen mode

illuminates.

In Cell mode, each cell is assigned a DMX address based on the DMX address

of the fixture (see

Setting the DMX address

page 7

) and the current DMX

control mode (see

Changing the DMX control mode

page 9

). For example,

if you set the DMX address on the fixture to 100, set the DMX mode to

5-channel, and set the Grouping mode to Cell, the starting DMX address of

the first cell will be 100 and the starting DMX address of the second cell will

be 105.

Group and Cell

LED indicators

Grouping

button

ETC Installation Guide

ColorSource Linear v1.5

ColorSource Linear v1.5 Page 10 of 16 ETC

DMX control channels

Linear 1 and Linear 2/Linear 4 in Group mode

*Original ColorSource Linear fixture uses blue in channel 4; Deep Blue

ColorSource Linear fixture uses indigo in channel 4.

DMX

Channel



(5 Channel)

dir

(Direct)

1ch

(1 Channel)

rgb

(RGB)

1 Intensity Intensity Intensity Red

2 Red Red Green

3 Green Green Blue

4Blue

Blue/Indigo*

5 Strobe Lime

6Strobe

Otros manuales para ColorSource Linear

Tabla de contenidos

Otros manuales de Equipo de DJ de ETC

ETC

ETC ColorSource PAR Manual de usuario

ETC

ETC Source Four Mini LED Manual de usuario

ETC

ETC fos/4 Series Manual de usuario

ETC

ETC Source Four PARN Manual de usuario

ETC

ETC Source Four LED Series Manual de usuario

ETC

ETC Source Four LED Series Manual de usuario

ETC

ETC Source Four jr Manual de usuario

ETC

ETC IRIDEON AR500 Manual de usuario

ETC

ETC Releve Spot Instrucciones de montaje

ETC

ETC Releve Spot Manual de usuario

ETC

ETC Ion Classic Manual de usuario

ETC

ETC Source Four Zoom Manual de usuario

ETC

ETC Desire D40 Manual de usuario

ETC

ETC SolaPix 19 XT Manual de usuario

ETC

ETC Element Manual de usuario

ETC

ETC ColorSource Linear Manual de usuario

ETC

ETC Irideon FPZ Manual de usuario

ETC

ETC RoadHog 4 Manual de usuario

ETC

ETC ColorSource Spot V 1.0 Manual de usuario

ETC

ETC Source Four PAR Manual de usuario

ETC

ETC Source 4WRD Manual de usuario

ETC

ETC Source Four LED Series Manual de usuario

ETC

ETC Desire series Guía de configuración

ETC

ETC Source Four LED Series Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario