ESYLUX PD-FLAT 360i/6 mini DALI Manual de usuario

PD-FLAT 360i/6 mini DALI

EP10427503

PD-C 360i/8 mini DALI

EP10427510

ESYLUX GmbH | An der Strusbek 40

22926 Ahrensburg | Germany

[email protected] | www.esylux.com

Operating instructions

MA00940001

09/2015

OPERATING INSTRUCTIONS

PD-FLAT 360i/6 mini DALI

PD-C 360i/8 mini DALI

2 / 20

Table of contents

1 Using the manual 4

2 Safety instructions 4

3 Intended use 4

4 Description of the devices 5

5 Included in delivery 5

6 Technical data 6

7 Operating elements 6

8 Maintenance 6

9 Cleaning 7

10 EC Declaration of Conformity 7

11 Activation 7

Installation types 7

Connecting the device 7

Wiring diagram 8

Factory settings 8

12 Operating mode 9

Automatic switch-on 9

Automatic switch-off 9

Switch-off delay time 10

Light value 10

Delay 10

Orientation light 11

OPERATING INSTRUCTIONS

PD-FLAT 360i/6 mini DALI

PD-C 360i/8 mini DALI

3 / 20

Switch-off warning 12

Fully automatic mode 12

Semi-automatic mode 13

100 h burn-in function 13

Corridor function 14

LED feedback 14

Sensitivity 14

Electronic ballast DALI parameters 15

Switch input 15

Master / slave function 16

Twilight switch mode 17

Querying the active mode 18

Reset 18

13 Accessories 19

14 Disposal 20

15 ESYLUX manufacturer's guarantee 20

OPERATING INSTRUCTIONS

PD-FLAT 360i/6 mini DALI

PD-C 360i/8 mini DALI

4 / 20

1 Using the manual

This manual is intended to provide valuable information to you as the user and

integrator on how to use and configure the device and to take full advantage of the

range of functions.

Please store this manual with your documentation for the premises for future

reference so you can find the correct answer if questions arise.

If you have any questions that are still unanswered, please visit our website at

www.esylux.com or contact our technical helpline directly on +49 (0) 4102 489 489.

2 Safety instructions

• CAUTION: Work on the 230 V power system must be performed by authorised personnel

only, with due regard to the applicable installation regulations / standards.

• Switchoffthepowersupply/DALIbusvoltagebeforeinstallingthesystem.

• Observetheapplicablesafetyregulationswhenworkingonelectricalsystems.

3 Intended use

The detector is designed to be connected to DALI systems to automatically control the

switching on or dimming of lighting according to ambient light or when movement /

presence is detected.

OPERATING INSTRUCTIONS

PD-FLAT 360i/6 mini DALI

PD-C 360i/8 mini DALI

5 / 20

4 Device description

The ESYLUX ceiling-mounted presence detector is a passive infrared presence

detector that responds to moving heat sources, such as people walking. The presence

detector is designed for small rooms and passageways that benefit from natural light.

Parameters can be configured using the ESYLUX Mobil-PDi/MDi and Mobil-PDi/MDi

universal remote controls as well as via the manual setting elements.

NOTE: Use this product only as intended (as described in the user instructions). The

device must not be changed, modified or painted – doing so will void any warranty

claims. You must check the device for damage immediately after unpacking it. If there

is any damage, you should not install the device under any circumstances. If you

suspect that safe operation of the device can not be guaranteed, you should turn the

device off immediately and make sure that it cannot be operated unintentionally.

5 Included in delivery

Please check the contents of the delivery immediately after unpacking the device.

1. Presence detector

2. 2 x WAGO micro-terminals

3. Locking ring

4. Spring clamp

5. Screw

6. Tool

7. Holding disc for lens mask (PD-C360i/8 mini DALI only)

8. Lens mask to mask fields of detection (PD-C360i/8 mini DALI only)

OPERATING INSTRUCTIONS

PD-FLAT 360i/6 mini DALI

PD-C 360i/8 mini DALI

6 / 20

6 Technical data

PD-FLAT 360i/6 mini DALI / PD-C 360i/8 mini DALI

Operating voltage DALI 16 V ⎓

Contact Max. 0.8 mm 2 / plug-in terminal

Protection type IP 55

Operating temperature range 0 °C to +50 °C

Approx. dimensions H 39 mm / mH 60 mm, Ø 33 mm

Installation bore diameter 25 mm

Communication Broadcast / non-addressable

7 Operating elements

The presence detector has no setting elements. The adjustable parameters can be

configured via remote control.

8 Maintenance

The presence detector has no serviceable parts.

OPERATING INSTRUCTIONS

PD-FLAT 360i/6 mini DALI

PD-C 360i/8 mini DALI

7 / 20

9 Cleaning

To clean the detector, use a slightly damp, lint-free cloth and normal domestic soap.

Beware of harsh detergents, which can corrode the surface of the detector affecting its

ability to detect movement and light.

10 EC Declaration of Conformity

The CE label corresponds to the following directives:

• EMC 2004/108/EC

• RoHS 2011/65/EU

11 Activation

Installation types

Recessed ceiling mounting. The presence detector is mounted in a false ceiling by

inserting the device into the hole and clamping it in place using either a spring clamp

or locking ring.

Connecting the device

Switch off the DALI bus before connecting the device. The electrical contact is

established using WAGO micro-terminals, each of which can be used to connect up

to five cables with rigid wire ranging from 0.6 mm

2to 0.8 mm

2. Observe the polarity.

For DALI, avoid ring-shaped connection structures as these can cause problems. Other

connection structures are permitted

OPERATING INSTRUCTIONS

PD-FLAT 360i/6 mini DALI

PD-C 360i/8 mini DALI

8 / 20

Wiring diagram

The max. cable length of the DALI bus cable is 300 m

when using 1.5 mm

2cable.

Laying the DALI bus in combination with the mains cable

is not recommended.

Note: The DALI bus is not classified as SELV.

Factory settings

After the power supply is connected, the device switches to Start mode. After approx.

30 seconds, the device is fully booted and ready for operation. The first time the

device is switched on, it starts with the factory settings. The next time the device is

switched on, it has the most recently configured parameters.

Light value 500 lux

Switch-off delay time 5 minutes

Mode Fully automatic

Orientation light On (10 %)

Operation mode Master

The presence detector is a control device with an integrated interface supply. There

is no need to address the lights / electronic ballasts. All ballasts are addressed at the

same time via the broadcast address. A maximum of 25 DALI/DSi electronic ballasts

can be connected.

The detector can be mounted on the ceiling in any orientation.

OPERATING INSTRUCTIONS

PD-FLAT 360i/6 mini DALI

PD-C 360i/8 mini DALI

9 / 20

12 Operation

If the ambient lighting level is higher than the default light value, the connected

lighting is switched off.

Automatic switch-on

If the detector is triggered by movement and the ambient lighting level falls below the

default light value.

The red LED is enabled to indicate motion detection = two short flashes each time

movement is detected. Should there be a change in the natural light value, the

artificial light will be adjusted accordingly.

Automatic switch-off

If movement is no longer detected, the lighting is switched off once the set time

has elapsed. If the ambient lighting level is higher than the default light value, the

lighting is switched off after five minutes.

NOTE: However, should the natural lighting level increase and the ambient lighting

level exceed the preset light value, the detector automatically switches the lighting

off after five minutes regardless of any movement / presence. The lighting can then

be switched manually at any time via remote control or DALI button. For further

information, see the instructions for the remote control.

OPERATING INSTRUCTIONS

PD-FLAT 360i/6 mini DALI

PD-C 360i/8 mini DALI

10 / 20

Switch-off delay time

The switch-off delay time is the period of time the lighting remains switched on after

the last movement was detected. The time can be set to between one and thirty

minutes via remote control.

Function Customised setting

Enter programming mode

The detector goes into programming mode.

Acknowledgement: The red LED lights up permanently and the lighting is

switched on permanently.

Switch-off delay time

The switch-off delay time starts once movement is no longer detected in the

field of detection.

Acknowledgement: the red and blue LEDs flash three times.

Exit programming mode

The set parameters are stored on the detector.

Acknowledgement: The red LED is switched off.

Light value

The light value is the ambient lighting level that determines when the detector is

activated. When motion is detected below this ambient lighting level, the lighting is

switched on. When motion is detected above this ambient lighting level, the detector

does not respond.

To determine the ambient lighting level, first open programming mode and exit once

the settings have been configured successfully (also see “Switch-off delay time”).

In programming mode, the “Eye button” can be used to read and store the current

light value.

Delay

When persons are present, in order to avoid sudden changes in brightness caused

by undesired switching on / off of the lighting, the detector is only triggered after a

time delay.

Example: a passing cloud could potentially cause unnecessary switching.

Time delay from dark to light: 5 min. = red LED flashes slowly during this period.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sensor de seguridad de ESYLUX

ESYLUX

ESYLUX PD 360i/8 DALI ADR Manual de usuario

ESYLUX

ESYLUX PD-C360i/24 DUOplus-FM Manual de usuario

ESYLUX

ESYLUX PD-C360i/24 DUODIMplus-FM Manual de usuario

ESYLUX

ESYLUX PD-C360i/24 DIMplus-FM Manual de usuario

ESYLUX

ESYLUX MD-C360i/8 Series Manual de usuario

ESYLUX

ESYLUX PD-C360i/8 DUO DALI Manual de usuario

ESYLUX

ESYLUX COMPACT APC10 DALI-2 Manual de usuario

ESYLUX

ESYLUX PROTECTOR KRF TCV 2G Guía del usuario

ESYLUX

ESYLUX PD-C360i/24 DIMplus Manual de usuario

ESYLUX

ESYLUX MD 180i/16 BASIC CH Manual de usuario

ESYLUX

ESYLUX COMPACT PD-C 360/8 BMS DALI-2 Manual de usuario

ESYLUX

ESYLUX RC 130i Manual de usuario

ESYLUX

ESYLUX MD 120 Manual de usuario

ESYLUX

ESYLUX PD 360/8 KNX BASIC Manual de usuario

ESYLUX

ESYLUX RC 130i Manual de usuario

ESYLUX

ESYLUX PD 360/8 Basic Manual de operación y mantenimiento

ESYLUX

ESYLUX SMB MD 360i/24 Basic SMB Manual de operación y mantenimiento

ESYLUX

ESYLUX PD-C360i/8 mini KNX Manual de usuario

ESYLUX

ESYLUX PD-C360i/24 DUODIMplus-FM Manual de usuario

ESYLUX

ESYLUX PD-C180i KNX ECO Manual de usuario

ESYLUX

ESYLUX EM10041006 Manual de usuario

ESYLUX

ESYLUX MD-C360i/6 mini Manual de usuario

ESYLUX

ESYLUX MD 120 Manual de usuario

ESYLUX

ESYLUX MD-C360i/6 mini Manual de usuario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario