ESX VISION VNC1045-DBJ Manual de usuario
1
V1.6
INSTALLATION
GUIDE
VNC1045-DBJv2
2
IMPORTANT NOTES
This guide is an aid for the professional installation of the device.
Please note the following notes before installation:
• Always handle all parts of the device and the components of your vehicle with
care.
• Under all circumstances observe the regulations of the vehicle manufacturer
and do not make any changes to the vehicle which could impair driving safety.
• For safety reasons, disconnect the vehicle battery’s ground connection before
installation.
• Please always pay attention to the correct polarity of the connections.
• Please do not modify any harnesses or connections of the device or the vehicle
as this may affect the warranty.
• Make sure that no cables are squashed or cause a short circuit.
• Do not lay cables in front of the airbags, e.g. in the dashboard or in a way that
affects their function.
3
RECOMMENDED TOOLS:
RECOMMENDED ACCESSORIES:
Unlock devices Plastic mounting wedges
Cable ties Phillips screwdriver or bit
Steering wheel control adapters:
VNA-LFB-FD2
FIAT DUCATO IV, PEUGEOT BOXER III, CITROËN JUMPER III (Type 290, since
2015) with radio preparation, ISO connection
VNA-LFB-FD3
FIAT DUCATO IV, PEUGEOT BOXER III, CITROËN JUMPER III (Type 290, since
2015) with original radio or original navigation system, CAN bus (52-PIN), USB port
(optional), AUX port (optional)
VNA-LFB-FD4
FIAT DUCATO IV, PEUGEOT BOXER III, CITROËN JUMPER III (Type 290, since
2015) with original radio Delphi F250, ISO connector
VNA-LFB-FD5 (included)
FIAT DUCATO III, PEUGEOT BOXER II, CITROËN JUMPER II (Type 250, 2006 -
2015) ISO connection
Plastic drill
Ø 20 mm
Torx screwdriver or bit
4
INSTALLATION GUIDE
Only with radio ex-factory:
Pull the radio out of the slot
using the release tools.
Only with radio ex-factory:
Loosen the 4 screws.
Open the storage tray and loosen the 2
screws.
Only with radio ex-factory:
Remove the connectors on the back of the radio.
Loosen the 2 screws underneath.
Pull the storage tray upwards.
5
INSTALLATION GUIDE
The dashboard should now look like this. Loosen the 2 screws.
Loosen the 2 screws underneath. Remove the ventilation ducts on the left and
right with a screwdriver and leverage as
shown.
Lift the rubber tray and remove the screw underneath.
6
INSTALLATION GUIDE
Remove the original panel.
Loosen the 2 screws.
PRELIMINARY
Remove the original panel
by lifting it and pulling it
forward.
Release the plugs.
7
INSTALLATION GUIDE
Remove all marked clips from the
original panel and attach them to
the supplied enclosed panel.
Loosen the 2 screws.
Loosen the screw on the right side below the
steering wheel.
Pull the cover out from back to top (as
shown).
Loosen the 2 screws and put the speedome-
ter display on top (The plugs can stay).
Loosen the screws on the left side below the
steering wheel.
+ 1x Screw
8
INSTALLATION GUIDE
Put in the storage tray and lift it, then attach the 2 screws.
Then install the supplied enclosed panel,
where the GPS antenna is integrated.
Pay attention to the GPS cable and fasten the
2 screws.
Then insert the cable of the GPS antenna to
the device and connect it to the GPS socket
as described on page 14.
Attach the 2 screws on the front. OBD connection* (optional):
Remove the cover from the fuse box. Loosen
the screw.
9
INSTALLATION GUIDE
Connect the respective cables to the ESX device as described on page 10.
OBD connection* (optional):
Lay the OBD connection cable.
(like shown)
OBD connection* (optional):
Remove the cap of the OBD
connector.
OBD connection* (optional):
Connect the supplied OBD connector.
Place the microphone.
Lay the microphone cable
as shown.
(Picture shows cable with factory installed radio) (Picture shows cable without factory installed radio)
* Optional accessories
10
INSTALLATION GUIDE
Put in the speedometer display and the cover. Slide the ESX device into the slot.
Attach the screws. ESX device after the installation.
Attach the screw and set in the rubber tray.
Otros manuales para VISION VNC1045-DBJ
1
Tabla de contenidos
Otros manuales de Sistema de navegación para automóviles de ESX
ESX
ESX VNS720 VW-U1 Manual de usuario
ESX
ESX VN710 KI-SORENTO Manual de usuario
ESX
ESX VISION VNC1045-DBJ Manual de usuario
ESX
ESX Vision Series Manual de usuario
ESX
ESX VN720 VO-P6C Manual de usuario
ESX
ESX VNS730 FI-DUCATO Manual de usuario
ESX
ESX VN830 SK-OC3 Manual de usuario
ESX
ESX VN710 KI-CEED Manual de usuario
ESX
ESX VISION ANDROID Series Manual de usuario
ESX
ESX VNS830 SK-OC3 Manual de usuario
