Estyma IGNEO Touch Manual de usuario

User manual

EG-Pellet

Table of contents
Chapter 1. General information 4
1  Introduction................................................................................................................................................... 4
2  Safety.............................................................................................................................................................. 4
3  Disposal of Waste of Electrical and Electronic Equipment ............................................................... 
Chapter 2. Basic controller operation 6
1  Main screen................................................................................................................................................... 6
1.1  DATE AND TIME - SETTING........................................................................................................7
1.2  TURNING THE BOILER ON/OFF................................................................................................7
1.3  TURNING ON/ OFF the bo ler, water, heat ng........................................................................7
1.4  SUMMER (only water heat ng)......................................................................................................7
1.5  SETTING THE TARGET BOILER TEMPERATURE (program) ...............................................8
1.6  FUEL FILLING (sett ng the fuel level)..........................................................................................8
2  Menu structure............................................................................................................................................. 9
Chapter 3. Detailed description of screens/functions 10
1  Boiler............................................................................................................................................................ 10
1.1  SET TARGET TEMPERATURE AND OPERATING MODE..................................................10
1.2  SETTINGS........................................................................................................................................10
2  Schedules..................................................................................................................................................... 11
3  Heating and hot water operation modes.............................................................................................12
4  Heating......................................................................................................................................................... 12
4.1  SETTINGS........................................................................................................................................12
  Hot water..................................................................................................................................................... 13
5.1  SETTINGS........................................................................................................................................13
6  Burner........................................................................................................................................................... 13
6.1  SETTINGS........................................................................................................................................13
7  Buffer............................................................................................................................................................ 14
7.1  SETTINGS........................................................................................................................................14
8  Solar heating............................................................................................................................................... 14
8.1  SETTINGS........................................................................................................................................14
9  Alarms........................................................................................................................................................... 14
www.estyma.pl 3 
EGP-EN 20171024

IGNEO touch user manual

Chapter 1. General information

Thank you for choosing our product and congratulations on the best decision. We are happy to hear your comments

about the device.

ESTYMA electronics Team

1.1 INTRODUCTION

The bo ler regulator IGNEO Touch s a modern m croprocessor system, wh ch manages not only the bo ler, but

also the heat ng system. In the full conf gurat on, the regulator can manage:

4 central heat ng c rcu ts

1 hot water c rcu t.

1 buffer

1 solar heat ng system

1 add t onal fuel storage system

Thanks to advanced algot thm and the poss b l ty to regulate mult ple parameters, the system can be well adjusted

to the heat ng system needs.

1.2 SAFETY

ATTENTION! Electrocution risk!

Turn off power on the electr c sw tchboard before assembly or d sassembly.

Carefully read the nstruct on before use.

Keep the nstruct on manual and consult t when us ng the dev ce.

Ab de by the rules of use and warn ngs wr tten n the nstruct on manual.

Check f the dev ce sn't dammaged. When n doubt, don't use the dev ce and contact the reta ler.

If you encouter s tuat ons not ment oned n the nstruct on manual, or you are n doubt about safe usage

of the dev ce, please contact the reta ler.

Pay attent on to any warn ng symbols on the dev ce or packag ng.

The dev ce must be used n accordance w th ntended use.

The dev ce s not a toy, keep out of ch ldrens reach.

Under no c rcumstances allow ch ldren to play w th any part of the packag ng.

Keep small parts (screws, wall plugs etc.) away from ch ldren. Small elements suppl ed w th the dev ce can

be a chok ng hazard.

Do not mod fy mechan cal or electr cal parts of the dev ce. It can result n abnormal funct on ng, malfunct ons,

errors and fa lure to comply w th regulat ons.

Do not put anyth ng nto any open ngs n the dev ce. It can cause short c rcu ts, electr c shock, f re or

complete destruct on of the dev ce.

Do not allow the dev ce to come n contact w th water, mo sture or dust. It can cause short c rcu ts,

electr c shock, f re or complete destruct on of the dev ce.

4www.estyma.pl

EGP -EN 20171024

Chapter 1. General nformat on

After turn ng off the dev ce us ng touch panel, t can st ll be under power.

Th s regulator s des gned as a part of a bo ler, not a standalone dev ce.

Th s dev ce requ res a proper vent lat on. Do not cover any vent lat on holes to assure a proper a r c rculat on.

For ns de use only, unless stated otherw se.

Do not expose to mpacts or v brat ons.

Before nstall ng ver fy f electr cal gr d parameters are w th n spec f cat ons.

To ensure electr c shock protect on, ver fy that the dev ce s grounded. It must be connected w th a 3 p n

socket. The power socket must be nstalled by an author zed electr c an.

Ver fy f the dev ce w ll not cause power gr d overload. Do not connect the dev ce to a c rcu t conta n ng

electr c motors and other mpulse d srupt on sources (freezers, wash ng mach nes etc.)

Before connect ng any w res or external dev ces, turn off ma ns supply.

To completely turn off the dev ce, pull the plug out of the socket. Espec ally f t w ll not be used for an

extended ammount of t me.

The power cord must be protected from damage. It must not be stepped on and no objects should be

placed on t.

The regulator must be nstalled by the bo ler producer. Any electr cal connect ons must comply w th

c rcu t d agrams and local standards and regulat ons.

Add t onal safety dev ces must be used to protect the bo ler and heat ng elements from eventual regulator

malfunct ons or software errors.

Th s dev ce has no replaceable parts. All serv c ng and repa r, apart from clean ng and c rcu t breaker replacement

(electr cal gr d d sconnected) and chang ng sett ngs must be performed by an author zed profes onals.

Before any serv ce act v ty d sconnect the dev ce from any power sources.

Do not use gasol ne, solvents or other chem cals for clean ng. It can damage the panel. Use soft cloth nstead.

If the power cord s damaged, do not use the dev ce. Damaged cable must be replaced w th one w th the

same parameters by the serv ce department.

Sett ngs must be adjusted to a type of bo ler and fuel, accomodat ng for all other cond t ons. Incorrect

sett ngs can result n fa lure. In extreme cases t can lead to l fe threaten g s tuat ons.

The regulator s ment to be nstalled by a bo ler producer. Before us ng t n a dev ce, the producer must

ver fy that t's compat ble w th the bo ler type, and ts use w ll not cause any danger or malfunct ons.

1.3 DISPOSAL OF WASTE OF ELECTRICAL AND ELECTRONIC EQUIPMENT

Th s electron c dev ce cons sts of partly recycleable mater als. It has to be d sposed of by tak ng t to a des gnated used

electr c and electron c equ pment collect on po nt or a reta ler. It should not be m xed w th general household waste.

www.estyma.pl 5

EGP-EN 20171024

IGNEO touch user manual

Chapter 2. Basic controller operation

2.1 MAIN SCREEN

Screen sett ngs:

NUMBER DESCRIP ION

1Current t me. On press ng, the change of hour screen s d splayed.

2Burner status.

3Measured bo ler temperature.

4Day of the week. On press ng, the change of date screen s d splayed.

5Measured outs de temperature.

6Set target temperature of the bo ler and bo ler mode. On press ng t changes.

7Enter the menu button.

8Enter the fuel level sett ngs button. The button also d splays the rest of the fuel and nforms about the

reserves.

9 Qu ck enter the burner menu button. L t lamp means the burner s work ng.

10,11 Qu ck enter the heat ng menu button. L t lamp means the c rcu t s work ng.

12 Qu ck enter the hot water menu button. L t lamp means that the water preparat on s work ng.

13 Advanced button. Long press (>3 sec) turns the bo ler off. L t lamp means that the bo ler s work ng,

LED descr pt on:

LE ER DESCRIP ION

A (green) Bo ler. It s l t f the bo ler s work ng.

B (yellow) Burner. It s l t f there s a flame, t s flash ng f the burner s work ng but there s no flame (eg. nflam ng,

putt ng out). It s not l t f the burner s not work ng and there s not flame.

C (red) Alarm. It s flash ng f the alarms are act ve. It s l t f there are unconf rmed alarms.

6www.estyma.pl

EGP -EN 20171024

Chapter 2. Bas c controller operat on

2.1.1 DATE AND TIME - SETTING

To set the date or t me on the ma n screen, press the date or the hour. The w ndow to set the date or hour w ll appear.

2.1.2 TURNING THE BOILER ON/OFF

In order to turn the bo ler on or off, press the button on

the ma n screen for 3 seconds.

2.1.3 TURNING ON/ OFF he boiler, wa er, hea ing

On press ng the button on the ma n screen t s poss ble to qu ckly turn on/off (change of the operat ng mode) of

certa n heat ng system elements.

ATTENTI N! If there are more than two heating system circuits, you should enter the menu, and

then go to the circuit number 3 and 4 to change the heating program.

2.1.4 SUMMER (only wa er hea ing)

To turn on summer mode (heat ng only hot water c rcu t), press the On/Off button and move all the ''Heat ng''

sl ders to ''off''.

ATTENTION! If there are more than two heating circuits in the system you should enter the

menu and then go to the circuit number 3 and 4 to turn off the heating.

www.estyma.pl 7

EGP-EN 20171024

IGNEO touch user manual

2.1.5 SETTING THE TARGET BOILER TEMPERATURE (program)

To change the bo ler target temperature or the bo ler work ng program you should press the button w th the

target temperature and the current program on the ma n screen, and then set the temperature or change the

program.

The programs are descr bed n 3.1.1.

2.1.6 FUEL FILLING (se ing he fuel level)

The regulator was equ pped w th the ab l ty to calculate the rema n ng fuel n the tank. To make calculat ng

poss ble, each t me after add ng fuel you should set the amount of the fuel n the tank. The amount s set by the

buttons ''+'' and ''-'' or by the sl der.

Th s screen also allows to turn on the fuel conveyor manually. In case of comlete fuel deplet on t allows to f ll the

conveyor tube aga n.

To enter the fuel level menu, press the ''8'' button on the ma n screen.

8www.estyma.pl

EGP -EN 20171024

Chapter 2. Bas c controller operat on

2.2 MENU STRUCTURE

www.estyma.pl 9

EGP-EN 20171024

IGNEO touch user manual

Chapter 3. Detailed description of screens/functions

3.1 BOILER

3.1.1 SET TARGET TEMPERATURE AND OPERATING MODE

Bo ler target set temperature and operat ng mode can be

regulated after press ng number ''6'' on the ma n screen.

The follow ng table presents ava lable bo ler operat ng modes.

SYMBOL NAME DESCRIP ION

manual The bo ler temperature s set d rectly by the user. The bo ler works to ma nta n the

set target temperature.

automatic

The bo ler temperature s set automat cally on the bas s of the current need of the

heat ng c rcu ts, hot water c rcu ts or the buffer.

When there's no need to heat the water, the temperature w ll be set to m n mum

of 7°C (ant freeze mode), and the bo ler w ll turn on only when needed.

time- manual The bo ler temperature s set as n the manual mode, but the bo ler can work only

n set t me l m ts.

time- automatic The bo ler temperature s set as n the automat c mode, but the bo ler can work

only n set t me l m ts.

3.1.2 SETTINGS

NAME DESCRIP ION

Set temperature [°C] The set temperature n manual or t me manual mode.

Switching hysteresis [°C] The burner s turned on when the temperature n the bo ler s lower than the set

temperature, m nus the sw tch ng hysteres s.

Hysteresis exemption [°C] The burner s turned off f the temperature n the bo ler s h gher than the set

temperature plus hyster es s exempt on.

10 www.estyma.pl

EGP -EN 20171024

Otros manuales para IGNEO Touch

Tabla de contenidos

Otros manuales de Controladores de Estyma

Estyma

Estyma iGNEO COMPACT Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario