8. At this point the device is ready for use and will start registering the CO2
removal. The equipment at will show you the main screen.
9. Settings during Treatment
a) GAS Flow
Selecting the and buttons you can choose the desired air flow. You
can range between 4 to 15 L/ min or you can reset the flow.
By clicking on the button, you can confirm the value and the button
you can exit the window and selecting you can reset the flow.
b) CO2Removal
Selecting the and you choose the desired value of VCO2 to
extract. By clicking on the you confirm the value and the button you
exit the dialog and selecting the button you will disable this feature.
Operating Manual ProLUNG Meter Pag. 20/39
Rev4 – 2012-12-31
The equipment at this point will present the main screen shown in the figure below:
Figure 16
Use the touch screen to select one of the following functions:
Air Flow
CO2 Removed
Air Temperature
Treatment Data
Figure 17
Selecting the + and - buttons you can choose the desired air flow. The allowable
values are from 4 to 15 L/ min or you can reset the flow.
By clicking on the !button, you can confirm the value and the "button you can
exit the window and selecting Off #you can reset the flow.
Operating Manual ProLUNG Meter Pag. 21/39
Rev4 – 2012-12-31
Figure 18
Selecting the + and - you choose the desired value of VCO2to extract.
By clicking on the !you confirm the value and the "button you exit the dialog
and selecting the Off button #disables this feature.
Figure 19
Setting using the + and - you choose the desired value of the air temperature
supplied to the ProLUNG cartridge. By clicking on the !you confirm the value and
the "button exits the window and selecting the #Off button turns off the heater.
The graph of VCO2can be changed by selecting the scale of the individual
axes.
Operating Manual ProLUNG Meter Pag. 21/39
Rev4 – 2012-12-31
Figure 18
Selecting the + and - you choose the desired value of VCO2to extract.
By clicking on the !you confirm the value and the "button you exit the dialog
and selecting the Off button #disables this feature.
Figure 19
Setting using the + and - you choose the desired value of the air temperature
supplied to the ProLUNG cartridge. By clicking on the !you confirm the value and
the "button exits the window and selecting the #Off button turns off the heater.
The graph of VCO2can be changed by selecting the scale of the individual
axes.
Operating Manual ProLUNG Meter Pag. 21/39
Rev4 – 2012-12-31
Figure 18
Selecting the + and - you choose the desired value of VCO2to extract.
By clicking on the !you confirm the value and the "button you exit the dialog
and selecting the Off button #disables this feature.
Figure 19
Setting using the + and - you choose the desired value of the air temperature
supplied to the ProLUNG cartridge. By clicking on the !you confirm the value and
the "button exits the window and selecting the #Off button turns off the heater.
The graph of VCO2can be changed by selecting the scale of the individual
axes.
Operating Manual ProLUNG Meter Pag. 21/39
Rev4 – 2012-12-31
Figure 18
Selecting the + and - you choose the desired value of VCO2to extract.
By clicking on the !you confirm the value and the "button you exit the dialog
and selecting the Off button #disables this feature.
Figure 19
Setting using the + and - you choose the desired value of the air temperature
supplied to the ProLUNG cartridge. By clicking on the !you confirm the value and
the "button exits the window and selecting the #Off button turns off the heater.
The graph of VCO2can be changed by selecting the scale of the individual
axes.
Operating Manual ProLUNG Meter Pag. 21/39
Rev4 – 2012-12-31
Figure 18
Selecting the + and - you choose the desired value of VCO2to extract.
By clicking on the !you confirm the value and the "button you exit the dialog
and selecting the Off button #disables this feature.
Figure 19
Setting using the + and - you choose the desired value of the air temperature
supplied to the ProLUNG cartridge. By clicking on the !you confirm the value and
the "button exits the window and selecting the #Off button turns off the heater.
The graph of VCO2can be changed by selecting the scale of the individual
axes.
Operating Manual ProLUNG Meter Pag. 20/39
Rev4 – 2012-12-31
The equipment at this point will present the main screen shown in the figure below:
Figure 16
Use the touch screen to select one of the following functions:
Air Flow
CO2 Removed
Air Temperature
Treatment Data
Figure 17
Selecting the + and - buttons you can choose the desired air flow. The allowable
values are from 4 to 15 L/ min or you can reset the flow.
By clicking on the !button, you can confirm the value and the "button you can
exit the window and selecting Off #you can reset the flow.
Operating Manual ProLUNG Meter Pag. 21/39
Rev4 – 2012-12-31
Figure 18
Selecting the + and - you choose the desired value of VCO2to extract.
By clicking on the !you confirm the value and the "button you exit the dialog
and selecting the Off button #disables this feature.
Figure 19
Setting using the + and - you choose the desired value of the air temperature
supplied to the ProLUNG cartridge. By clicking on the !you confirm the value and
the "button exits the window and selecting the #Off button turns off the heater.
The graph of VCO2can be changed by selecting the scale of the individual
axes.
Operating Manual ProLUNG Meter Pag. 21/39
Rev4 – 2012-12-31
Figure 18
Selecting the + and - you choose the desired value of VCO2to extract.
By clicking on the !you confirm the value and the "button you exit the dialog
and selecting the Off button #disables this feature.
Figure 19
Setting using the + and - you choose the desired value of the air temperature
supplied to the ProLUNG cartridge. By clicking on the !you confirm the value and
the "button exits the window and selecting the #Off button turns off the heater.
The graph of VCO2can be changed by selecting the scale of the individual
axes.
Operating Manual ProLUNG Meter Pag. 21/39
Rev4 – 2012-12-31
Figure 18
Selecting the + and - you choose the desired value of VCO2to extract.
By clicking on the !you confirm the value and the "button you exit the dialog
and selecting the Off button #disables this feature.
Figure 19
Setting using the + and - you choose the desired value of the air temperature
supplied to the ProLUNG cartridge. By clicking on the !you confirm the value and
the "button exits the window and selecting the #Off button turns off the heater.
The graph of VCO2can be changed by selecting the scale of the individual
axes.
Operating Manual ProLUNG Meter Pag. 21/39
Rev4 – 2012-12-31
Figure 18
Selecting the + and - you choose the desired value of VCO2to extract.
By clicking on the !you confirm the value and the "button you exit the dialog
and selecting the Off button #disables this feature.
Figure 19
Setting using the + and - you choose the desired value of the air temperature
supplied to the ProLUNG cartridge. By clicking on the !you confirm the value and
the "button exits the window and selecting the #Off button turns off the heater.
The graph of VCO2can be changed by selecting the scale of the individual
axes.
Operating Manual ProLUNG Meter Pag. 21/39
Rev4 – 2012-12-31
Figure 18
Selecting the + and - you choose the desired value of VCO2to extract.
By clicking on the !you confirm the value and the "button you exit the dialog
and selecting the Off button #disables this feature.
Figure 19
Setting using the + and - you choose the desired value of the air temperature
supplied to the ProLUNG cartridge. By clicking on the !you confirm the value and
the "button exits the window and selecting the #Off button turns off the heater.
The graph of VCO2can be changed by selecting the scale of the individual
axes.
