ESTeem 195Eg Manual de usuario

QUICK START GUIDE

MODEL 195Eg

Before You Begin

•The ESTeem Model 195Eg wireless Ethernet radio modem is compatible with many different applications. The most

common application is to bridge two or more Ethernet devices or networks. This guide will demonstrate the basic

configuration and testing of a pair of 195Eg’s. For a more detailed information, please see the ESTeem Model 195Eg User’s

Manual.

•This guide assumes you have a working knowledge of Ethernet networking, TCP/IP protocol and how to identify and set the

TCP/IP address on your computer.

•The 195Eg can be configured using any current web browser software such as Internet Explorer, Netscape or Mozilla.

•The following procedure will provide an initial communication link between two or more Model 195’s for testing purposes.

All the example commands listed in this guide can be adjusted to fit your communication network. Please consult the

ESTeem Model 195Eg User’s Manual for more details.

Unpack Contents

Each node in your ESTeem Model 195Eg’s network may have different hardware components based upon the final installation

location (i.e Outdoor, Indoor, Point-to-point or Muti-Point). Antenna types, cable lengths, power supplies may be different, but

the following items will be required for basic setup:

Model 195Eg

AA109 Resource Disk

Antenna

(AA01S Displayed)

(2) Ethernet Cables

Power Supply

(AA175 Displayed)

Note: Your accessory model numbers may vary from the above, but you will need to locate each of above items to continue

configuration.

Front Panel Overview

(RS-232 Data Port and Second Ethernet Port Optional)

12 VDC Input

(Auxiliary

Connector )

Reset Switch RS-232

Configuration RJ-45 10/100BaseT

Ethernet Port

Transmit

LED

Receive

LED

Status

LED

Power over

Ethernet LED

Aux Power

LED

RS-232

Data Port

Second

Ethernet

Port

Antenna Overview

Antenna Connectors

(TNC Female-RP)

Antenna Port A

(Single Receive Antenna)

Antenna Port B

(Dual Receive Antennas)

Begin Programming

1. Assemble the ESTeem Model 195Eg using the following:

Power and Data Connection

PC with Web

Browser Software

RJ-45 10/100BaseT

Ethernet Port

10/100BaseT

Ethernet Cable

(Patch or Cross Over)

AA175 PoE

Power Supply

LAN In

10/100BaseT

Ethernet Cable

(Patch or Cross Over)

PWR

Data Out

AA109

Resource

Disk

Antenna Connections

Leave

Open

Single Antenna

Configuration Dual Antenna

Configuration

2. The Model 195Eg will link to other Model 195Eg’s on the network via the WLAN Media Access Control (MAC) address

found on the bottom of the case. This MAC address is six hexadecimal digits separated by colons and is configured at the

factory. Every MAC address in the world is unique and can not be changed. Complete the following chart to aid in your

configuration:

Name Serial Number IP Address Ethernet MAC WLAN MAC

Example Modem 1 E-14001

172.16.8.101 00:04:3f:00:01:01 00:04:3f:00:01:02

3. Configuration of the Model 195Eg is completed through the product’s internal web server. To access this configuration page,

you will need to enter the 195Eg’s IP address in your web browser. The IP address set at the factory is Class B (i.e.

172.16.x.x) address and is printed on the Quality Assurance sheet sent with each 195Eg. If the factory default address

matches your network configuration, please proceed to Using Setup, otherwise continue to step 4.

4. Install the ESTeem Discovery Utility. The ESTeem Discovery Utility will allow you to configure the IP address on the

Model 195Eg to match your network. Install the Discovery Utility on your computer by inserting the Resource Disk in your

CD drive.

Note: The ESTeem Resource Disk is stand-alone copy of the ESTeem Web site (Figure 1). Navigation of the Resource Disk is

as simple as using your web browser. All technical documentation, User’s Manuals and the ESTeem Utility Program is

available on the disk.

Place the ESTeem Utility CD in your CD-ROM drive. The CD will auto load the ESTeem main page

Note: If the page does not auto load, open your web browser and set your address line to D:\index.html (Where D: is the

drive letter for your CD-ROM drive).

From the Support Menu select ESTeem Utilities and click on Download ESTeem Discovery Utility.

Figure 1 –ESTeem Resource Disk Main Page

Note: This program is saved in a compressed file format.

Microsoft Windows XP® will open the file directly, but other

operating systems will require a common compression program

such as WinZip available for download at http://www.winzip.com

Double click on the 195EdiscoverySetup.exe file listed in the

window to install the program.

5. Set IP Address on the 195Eg. Connect the Model 195Eg to

your computer either direct to the Ethernet card or through a

HUB/Switch using a CAT-5e Ethernet cable. The Ethernet

port on the 195Eg supports Auto-Negotiation so either a

patch cable or crossover cable will work. Open the ESTeem

Discovery Program and press the Discover Modems button.

The Model 195Eg will be displayed in the program by the

Ethernet MAC address and Current IP Address (Figure 3).

Note: The SSID and Mode of Operation will be adjusted

later in the configuration.

Double-click on the 195Eg you wish to program and the Configure IP Address window will be displayed (Figure 4). Enter an

IP address and Subnet Mask for the 195Eg that matches your network subnet and press the OK button to save this to the

ESTeem. You will receive notification that the Configuration was Successful and the 195Eg will reboot. Proceed to ESTeem

Setup to continue configuration.

Setup Programming

You should now be ready to configure the Model 195Eg through your web browser. Open the web browser program and enter the

IP address of the ESTeem in the address line and press enter.

Figure 2- ESTeem Utility Download

Figure 3 – Discovery Program Main Page

Figure 4 – Change IP Address Window

1. When prompted, enter admin for both the username and password and press the OK button.

2. Select Setup on the top menu.

3. Press the drop-down menu and select AP Bridge and press the Next button.

Step 1 – Sign-In Screen

Step 3 – Select AP Bridge

4. Set the DHCP services to OFF and press the Next button.

5. Verify the IP address and netmask for the 195Eg (listed as bridge device) are correct press the Next button.

Step 4 – Turn DHCP Off

Step 5 – Verify IP Address

6. Enter in the Gateway address in the default route IP address block and any DNS information for the server. If this is not

know or on a network without a Gateway, leave these items at factory default.

7. All 195Eg modems in the network must be have the exact same Service Set Identification (SSID). The default SSID is

ESTeem and we will use this for demonstration. Enter the SSID as listed above and turn off the wireless security features by

selecting the NO radial. Press the Next button to continue.

Note: It is recommended that security be used in all wireless applications. This procedure will forgo the security configuration

for brevity. Please see the example applications and the security appendix for further information.

Step 6 – Enter Gateway Address

Step 7 – Enter SSID

8. A warning that wireless security is not enabled will be displayed. Press the Next button to continue.

9. All Model 195Egs on the network must be on the same radio channel, representing a particular frequency. If a particular

channel has not been assigned for use, leave the 195Eg at a default value of 6 and press the Next button.

Step 8 – Security Warning Screen

Step 10 – Set Radio Channel

10. Configure the repeater peer list by selecting Enable the repeater capability radial to YES (Above). Press the Add button to the

right of the repeater peer table and, using the chart created in the Begin Programming section of this guide, enter the

Wireless MAC (WLAN MAC) address of the opposite 195Eg (the 195Eg this unit you are programming will communicate

with) in the Peer 1 – MAC Addr field (right). Leave the Priority and Cost settings at the default values and change the Enable

Link radial to Enable and press the Create Repeater Peer button. Press the Next button.

11. Press the Commit Changes button and the modem will save all the changes made and reboot. The reboot time is

approximately 1 minute to be ready for operation.

12. Complete all steps in this Setup Programming section for the other Model 195Eg’s you will be testing before moving on the

Testing Communication section.

Example Addresses

Name Serial Number IP Address Ethernet MAC WLAN MAC

195Eg We Are

Programming E-14096

172.16.48.189 00:04:3f:00:01:01 00:04:3f:00:01:02

Opposite 195Eg We

Will Create Wireless

Link

E-14034

172.16.38.114 00:04:3F:00:0B:00

00:04:3F:00:11:02

Step 10 – Configure Peer Table

Otros manuales para 195Eg

Tabla de contenidos

Otros manuales de Módem de ESTeem

ESTeem

ESTeem Horizon 2.4 Manual de usuario

ESTeem

ESTeem 195Eg Manual de usuario

ESTeem

ESTeem 195Eg Manual de usuario

ESTeem

ESTeem 210C Manual de usuario

ESTeem

ESTeem 210C Manual de usuario

ESTeem

ESTeem 195H Manual de usuario

ESTeem

ESTeem 195Ed Manual de usuario

ESTeem

ESTeem 195Ea Manual de usuario

ESTeem

ESTeem 85 Manual de usuario

ESTeem

ESTeem MODEL 192E Manual de usuario

ESTeem

ESTeem Edge 900 Manual de usuario

ESTeem

ESTeem 192C Manual de usuario

ESTeem

ESTeem 195Eg Manual de usuario

ESTeem

ESTeem Edge 900 Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario