PROGRAMMING QUANTITIES
Both the quantity of espresso and the quantity of milk can be programmed for each function. This allows you to set the perfect
quantity of espresso and milk to suit your own taste. The set quantities are saved until a new quantity is set.
ESPRESSO, DOUBLE ESPRESSO, MILK FROTH
1. Fill the machine as if a specialty coffee is to be prepared (see the Powering Up Your Machine chapter on page 6).
2. If necessary, fold out the milk nozzle using the lever.
3. Place a suitable cup below the brew head or the milk nozzle.
4. Select the function that is to be reprogrammed. Press the appropriate button (a beep will sound) and keep it held down (another
beep will sound).
5. The machine starts to prepare espresso or make milk froth.
6. Only let go of the button once the quantity of milk or espresso that you want has passed through. You will hear three beeps. This
quantity is now saved under the corresponding function.
CAPPUCCINO AND LATTE MACCHIATO
This process must be carried out twice for latte macchiato and cappuccino: once for the quantity of espresso and once for the
quantity of milk:
1.
nozzle is folded out and there is a cup below the milk nozzle.
2. Start a second operation by pressing the appropriate button again. A beep will sound.
3. Wait until the quantity of milk has passed through.
4. As soon as the machine starts to make espresso, press the appropriate button again and hold it down. Another beep will sound.
5. Only let go of the button again once the quantity of espresso that you want has passed through. You will hear three beeps. Now
both the quantity of milk and the quantity of espresso are saved under the appropriate function.
RESET TO FACTORY SETTINGS
If the amount of espresso and amount of milk are to be reset to the amounts preset in the factory, proceed as follows:
1. Switch off the machine via the “On / Off” button.
2. Press the and buttons simultaneously and keep them held down.
3.
4. Let go of the and buttons. The amounts have now been reset to the factory settings.
1. Carefully unpack your espresso machine and remove all packing material. Wipe the grinding chamber, blades with a damp
2.
3. Pour coffee beans into the grinding chamber. Do not use more than 30g of coffee beans.
4. Secure the lid into the motor base. Align the arrow with the “” marking on the motor base.
5. Connect the coffee grinder to the power supply.
6.Turn the lid clockwise to the “” mark on the motor base. The coffee grinder will operate. Hold the lid at the “” position.
7. If the lid is released, it will return to the “” position and the coffee grinder will stop operating. Turn and hold the lid to the
“” position if you want the coffee grinder to operate again.
8. View the consistency of the coffee grounds from the transparent lid. Never remove the lid until the blades stop completely.
9. Once the desired ground size has been obtained, disconnect the power cable from the power outlet.
10. Remove the transparent lid and pour out the coffee ground.
NOTE
• Do not run the appliance continuously for more than 30 seconds. After a full 30 second cycle, allow the grinder to rest for
another three minutes before using it again.
USING YOUR COFFEE GRINDER
TROUBLESHOOTING YOUR MACHINE
Problem Reason Solution
The control panel does not light up /
the machine cannot be switched on.
The power cord is not inserted correctly
in the power outlet.
Insert the power cord.
The power outlet is defective. Try another power outlet.
No mains voltage is present. Check the fuse of the mains connection.
The control panel lighting is defective. Please contact us at
Too many machines connected to the
same circuit.
Reduce the number of machines in
the circuit.
No error can be identied. Please contact us at
There is too much water in the water
tank.
The water tank is not placed in its
mount correctly.
Place the water tank in the correct
position.
The drip tray is lled with water. Please clean the drip tray
The espresso machine is
malfunctioning.
Please contact us at
There is some coffee powder on the
lter edge.
Use a damp cloth to wipe away any
residual coffee powder
machine beeps constantly and the
panel does not light up.
There is no water in the water tank. 1. Detach the water tank from the
the section in the Powering Up Your
Machine chapter on page 6).
2. Place a cup underneath.
3. Press any button. Some water will run
through the water system into the
cup. The machine will stop beeping,
the red indicator light goes out and
the machine can be restarted.
4. Select the function you want again.
The red indicator light lights up
constantly.
The machine is defective. Please contact us at
The machine is clogged. Descale the machine (see the Cleaning
and Maintenance chapter on page 17).
The espresso runs very slowly into
the cup.
The brew head or the lter is clogged.
The machine is clogged. Descale the machine (see the Cleaning
and Maintenance chapter on page 17).
The espresso is too weak. There is not enough coffee powder in
the lter.
Pour the right quantity of coffee
the Powering Up Your Machine chapter
on page 6).
The set espresso quantity is too much
for the quantity of coffee powder in
the lter.
The perfect amount of espresso to suit
your own taste can be programmed
in the machine (see the Programming
Quantities chapter on page 10).
1110
