ESI Solution 3 Manual de usuario

INSTALLATION AND USE

Solution 3

ARTICULATING ARM and

KEYBOARD PLATFORM

SOLUTION 3 Rev A 4/17

Model SOLUTION 3

SOLUTION 3

PLEASE REVIEW these instructions before beginning the installation. Check that

all parts needed were provided with your order. Contact your supplier if any

operates to your satisfaction.

Solution 3 combines the AA360 articulating arm with the PL215 keyboard

platform. In this instruction booklet, installation of the two products will be

explained in sequence, beginning with the AA360.

AA360 PARTS PROVIDED

Articulating Arm (1)

Front Stopper (1) 5

/8" Wood Screws (11) 1" Wood Screws (11)

CAUTION:

This install requires a power tool or cordless drill. This is not a handtool

install.

Track (1)

Rear

Stop

Peel Off

Backing

Press

Firmly

/4"

ADDITIONAL TOOLS REQUIRED

• Drill (For Track Installation Only)

•1

/8" drill bit

STEP 1: Adhere Track

• Peel the backing from the adhesive

strips on top of the track.

• Adhere the track to the

underside of the work surface.

— Position the front edge of

the track 1

/4" from the front

edge of the work surface.

The front of the track is the

end with three holes.

•

• #2 Phillips drill bit

SOLUTION 3

Begin keyboard installation with STEP 5 on page 4.

STEP 2: Attach Track

• Drill 1

/8" pilot holes through

all 11 holes in the track.

— Drill the holes 5/8" deep or

1" deep, depending on

which wood screws will be

used. (A minimum work surface

thickness of 11

/2" is recommended

for the 1" screws.)

CAUTION: Be careful not to drill through the

work surface.

• Attach the track with screws through the eight rear

holes only, as shown.

STEP 3: Install Articulating Arm

• Slide the articulating arm onto

the track. Position it back far

enough so that you have access

to the front three holes on the

track.

STEP 4: Attach Front Stop

• Position the front stop onto the

front of the track and secure it

with the nal three wood screws.

Attach Through Rear

Eight Holes Only

Slide Back

Front

Stop

SOLUTION 3

Panhead

Screw

Socket

Screw

Mouse

Guards

ADDITIONAL TOOLS REQUIRED

• Phillips screwdriver

• Allen key (if changing mouse sides)

PL215 PARTS PROVIDED

Keyboard Platform (1) Palm Rest (2)

1 Each for

Keying and Mousing

Flathead Screw (4) Flange Nut (4) Cord Clips (2)Panhead Screw (4)

#8-32x1

/2#8x32 #8-32x5

CAUTION: Hand-tighten screws only. Do not use power tools.

The PL215 keyboard platform features a swivel mouse pad that can be

attached to either the left or right side.

• wrench.

STEP 5: Attach Palm Rests

• Attach the palm rests to the keyboard and

mouse platforms. Use the #8-32x5

/8panhead

screws and a Phillips screwdriver.

— Attach each palm rest with two

screws, as shown.

NOTE: The right-side mouse

platform can be switched to the

left side. First, remove the mouse

guards. Then uninstall the palm rest

from the mouse and keyboard platform.

Using a 1/8" Allen key and a 3/8" wrench

remove the screw and Acorn nut holding the mouse platform. Turn the mouse

platform and re-install the mouse guards and mouse platform on the left side. Then

Install the palm rests.

SOLUTION 3

STEP 6: Attach Keyboard Platform

• Attach the keyboard platform to the keyboard arm and track assembly

using the four athead screws and ange nuts.

— Be sure the ange on the nuts is facing upward.

IMPORTANT: The ange nuts must be fully tightened to ensure the nuts are

locked. Use a Phillips screwdriver.

Flathead

Screw

Flange

Nut

Flathead

Screw

Flange

Nut

SOLUTION 3

OPERATION

To Raise or Lower Keyboard:

• Tip the platform up to unlock.

• Move the platform to the desired height.

• Release the platform to lock it in place.

To Set Tilt Angle:

• Unlock the quick release handle on the right side of the arm.

• Adjust the tilt angle to the desired position.

• Lock the quick release knob.

To Use the Mouse Platform:

• Swivel the mouse platform outward

to access it.

• Swivel the mouse platform under

the keyboard platform to conceal it.

STEP 7: Manage Cables

• Adhere cord clips to the underside of

the keyboard platform as needed to

organize the keyboard and mouse

cables.

Cord Clip

800.833.3746esiergo.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Mobiliario de interior de ESI

ESI

ESI ESPREE Instrucciones de instalación

ESI

ESI ALL-FLEX FLEX2-SLV-V3 Instrucciones de instalación

ESI

ESI LIFT Manual de usuario

ESI

ESI Birdi Manual de lista de piezas

ESI

ESI Motific MOF24 Series Manual de usuario

ESI

ESI Enmo 2NM-C48-SLV Manual de lista de piezas

ESI

ESI CPUMINI Instrucciones de instalación

ESI

ESI ALL-FLEX FLEX3-SLV-V1 Instrucciones de instalación

ESI

ESI VICTORY ELECTRIC-3-LEG Manual de usuario

ESI

ESI ALL-FLEX Instrucciones de instalación

ESI

ESI 3V-LX-C4848-30 Series Manual de usuario

ESI

ESI TRIUMPH 2T-C28-24 Manual de usuario

ESI

ESI FLEX2-SLV Manual de usuario

ESI

ESI Trada 2-Leg Manual de usuario

ESI

ESI FLEXRISE2 Manual de usuario

Manuales populares de Mobiliario de interior de otras marcas

Homelegance

Homelegance California 1662PEK-1CK Manual de usuario

Osmond Ergonomics

Osmond Ergonomics FLO Manual de usuario

OVE

OVE ELOISE 42 Manual de usuario

overstock

overstock MF286255 Manual de usuario

Sonoma

Sonoma 160-801 Manual de usuario

BOLERO

BOLERO Wicker Side Chair CF158 Guía de instalación

Coaster

Coaster 4799N Manual de usuario

Stor-It-All

Stor-It-All WS39MP Manual de programación

Lexicon

Lexicon 194840161868 Manual de usuario

Next AMELIA NEW 462947 Manual de usuario

Furinno

Furinno 18089 Manual de usuario

Munchkin

Munchkin Push to Close MK0001 Manual de usuario

impekk

impekk Manual II Manual de usuario

Elements

Elements Ember Nightstand CEB700NSE Manual de usuario

JWA

JWA CARY 68429 Manual de usuario

VIPACK

VIPACK AMORI AMKB9014 Manual de usuario

Anthro

Anthro GT03 Series Manual de usuario

Rowico

Rowico SANNA Manual de usuario