ESAB Migmaster 215 pro Manual de usuario

Valid for serial no. 012, 0140349 301 164 101118

Migmasterr215 Pro

Instruction manual

Manuel d’instructions Instrucciones de uso

-- 2 --

Rights reserved to alter specifications without notice.

Sous réserve de modifications sans avis préalable.

Reservado el derecho de cambiar las especificaciones sin previo aviso.

ENGLISH 3..............................................

RANÇAIS 13.............................................

ESPAÑOL 23..............................................

ENGLISH

-- 3 --

TOCe

1 DIR CTIV 4........................................................

2 SAF TY 4...........................................................

3 INTRODUCTION 6...................................................

3.1 Equipment 6................................................................

4 T CHNICALDATA 6.................................................

5 INSTALLATION 7....................................................

5.1 Placing 7...................................................................

5.2 Electricalinstallation 7.......................................................

5.3 Mainspowersupply 8........................................................

6 OP RATION 9.......................................................

6.1 Connectionandcontroldevices 9.............................................

6.2 Switching--on and overheating protection 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.3 Operation 10................................................................

6.4 Wirefeedpressure 10........................................................

7 MAINT NANC 11....................................................

7.1 Inspectionandcleaning 11....................................................

8 FAULTTRACING 12...................................................

9 ORD RINGOFSPAR PARTS 12......................................

DIAGRAM 34............................................................

W ARCOMPON NTS 39.................................................

ACC SSORI S 40.......................................................

-- 4 --

MM215Pe

1 DIR CTIV

D CLARATION OF CONFORMITY

ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that weld-

ing power source

Migmasterr215 Pro

from serial number 012, 014 are constructed and tested in

compliance with the standard EN 60974--1 /--5 and EN 60974--10 (Class A) in accordance with the

requirements of directive (2006/95/EC) and (2004/108/EEC).

--------------------------------------------------------------------------------------------------------------------------------------

Kent Eimbrodt

Global Director

Equipment and Automation

Laxå 2010--03--24

2 SAF TY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety precautions

must meet the requirements that apply to this type of welding equipment. The following recommen-

dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result

in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding

2. The operator must ensure that:

Sno unauthorized person is stationed within the working area of the equipment when it is

started up.

Sno--one is unprotected when the arc is struck

3. The workplace must:

Sbe suitable for the purpose

Sbe free from drafts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

SDo not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during operation.

-- 5 --

MM215Pe

WARNING

Read and understand the instruction manual before installing or operating.

Arc welding and cutting can be injurious to yourself and others. Take precausions when welding.

Ask for your employer’s safety practices which should be based on manufacturers’ ha ard data.

ELECTRIC SHOCK - Can kill

SInstall and earth the welding unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES - Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS - Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE - Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROT CT YOURS LF AND OTH RS!

CAUTION!

Read and understand the instruction manual before

installing or operating.

WARNING!

Do not use the power source for thawing fro en pipes.

CAUTION!

This product is solely intended for arc welding.

Do not dispose of electrical equipment together with normal waste!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical equipment

that has reached the end of its life must be collected separately and returned to an

environmentally compatible recycling facility. As the owner of the equipment, you should

get information on approved collection systems from our local representative.

By applying this European Directive you will improve the environment and human

health!

-- 6 --

MM215Pe

3 INTRODUCTION

Migmaster 215 Pro is step controlled power source in a compact design, intended

for welding with solid steel, stainless steel or aluminium wire as well as tubular wire

with or without shielding gas.

The possibility of welding with homogeneous wire/shielding gas and welding with

gasless tubular wire is obtained by switching the + and -- connections on the

machine front.

SAB’s accessories for the product can be found on page 40.

3.1 quipment

The power source is supplied with:

SReturn cable 3m with return clamp

SShelf for gas cylinder

SInstruction manual

4 T CHNICAL DATA

Migmaster 215 Pro Migmaster 215 Pro

Voltage 208/230V, 1∼50/60Hz 208/230/460/575V, 1∼50/60Hz

Permissible load at

100% duty cycle 110A 110A

60 % duty cycle 160A 160A

20 % duty cycle 250A 250A

Setting range (DC) 40A/16.0V--250A/26.5V 40A/16.0V--250A/26.5V

Open circuit voltage 19.5--42V 19.5--52V

Open circuit power 200W 320W

Power factor at max load 0.92 0.92

Control voltage 42V, 50/60Hz 42V, 50/60Hz

Wire feed speed 55--748ipm (1.4--19m/min) 55--748ipm (1.4--19m/min)

Burnback time 0--0.5s 0--0.5s

Spot welding 0.4--3.5s 0.4--3.5s

Welding gun connection EURO EURO

Wire dimension range

.023--.045” (0.6--1.1mm)

.035--3/64” (0.9--1.2mm)

.030--.045” (0.8--1.1mm)

.023--.045” (0.6--1.1mm)

.035--3/64” (0.9--1.2mm)

.035--.045” (0.9--1.1mm)

Max diameter/weight

of wire bobin 12” (300mm)/33lb (15kg) 12” (300mm)/33lb (15kg)

Dimensions lxwxh 33,8x16,5x28,7”

(860x420x730mm) 33x17x32,7”

(840x430x830mm)

Weight 220lb (100kg) 304lb (138kg)

Operating temperature 14÷104 (--10 ÷+40

C) 14÷104 (--10 ÷+40

-- 7 --

MM215Pe

nclosure class IP 23 IP 23

Application classifica-

tion

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-

tain load without overloading.

nclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

5 INSTALLATION

The installation must be executed by a professional.

CAUTION!

This product is intended for industrial use. In a domestic environment this product may

cause radio interference. It is the user’s responsibility to take adequate precautions.

5.1 Placing

Position the welding power source such way that its cooling air inlets and outlets are

not obstructed.

5.2 lectrical installation

Mains voltage

The 208/230V voltage machines are factory--configured for 230V and are fitted with

appropriate marking tape on the mains cable, the multi voltage machines are factory

configured for highest rated voltage and are not equipped with mains cable.

-- 8 --

MM215Pe

Welding voltage polarity

Welding voltage polarity may be changed as shown below.

5.3 Mains power supply

Check that the unit is connected to the correct mains power supply voltage, and that

it is protected by the correct fuse size. A protective earth connection must be made,

in accordance with regulations.

Rating plate with supply connection data

Migmaster 215 Pro Migmaster 215 Pro

Voltage V 208/230V, 1∼50/60Hz 208/230/460/575V, 1∼50/60Hz

Current A

at 100% duty cycle 19/17 19/17/9/7

at 60% duty cycle 30/27 30.5/27.5/14/11

at 20% duty cycle 56/50 58/53/26/21

Cable area AWG 3 x 10 3 x 10

Fuse slow A35 35/35/20/16

-- 9 --

MM215Pe

6 OP RATION

General safety regulations for the handling of the equipment can be found on

page 4. Read through before you start using the equipment!

WARNING!

Rotating parts can cause injury, take great care.

WARNING -- TIPPING RISK!

There is a risk of tipping while transportation and operation, if the welding machine leans

more than 10

. In that case appropriate securing has to be provided !

6.1 Connection and control devices

1Mains supply switch 5b Connector [--], low inductance, for welding gun

or return cable (welding polarity change--over)

2Orange indicating lamp, overheating 6Knob for spot welding -- ON/O and time set-

ting

2a White indicating lamp “ON” 7Knob for wire speed setting

3Welding voltage switch, 7 steps (fine) 8Digital instrument -- V/A

3a Welding voltage switch, 3 steps (coarse) 9Connector for ”spool--on gun” (control wire)

3b Welding voltage switch, 12 steps 10 Knob for burn--back time setting

(located in wire feeder compartment)

4EURO -- connector for welding gun 11 Cable with plug, connected to the welding gun

connector (welding polarity change--over)

5Connector [+] for welding gun or return

cable (welding polarity change--over) 12 Creep start switch

(located in wire feeder compartment)

5a Connector [--], high inductance, for welding gun or return cable (welding polarity change--over)

208/230V 208/230/460/575V

-- 10 --

MM215Pe

6.2 Switching--on and overheating protection

When machine is switched on with the illuminated switch [1], its lamp is on. If the ma-

chine is not overheated (lamp [2] is off) it is ready to work. If the internal temperature

during welding becomes too high, the welding is interrupted and disabled. This state is

indicated by permanent lighting of the orange indicating lamp [2] on the front of the unit.

It resets automatically when the temperature falls down.

6.3 Operation

Operator can manually select and set welding parameters as follows:

Srequired welding voltage ( and thus welding current) with knob [3]

Sappropriate wire feed speed with knob [7]

Sburn--back time with potentiometer [10] located in the wire feeder compartment

Sspot welding, activated by turning the knob [6] clockwise, spot welding time

increases while turning the knob [6] clockwise; set knob [6] in the left utmost

position in order to return to the continuous welding.

If the welding gun is used, welding process starts after its trigger is pressed and the wire

speed is controlled with potentiometer [7] on the front panel.

If the spool--on gun is used, welding process starts after its trigger is pressed, the spool--

on gun motor starts and wire speed is controlled with the potentiometer in the spool--on

gun grip.

Note: or spool--on gun current cable connection it is necessary to use the OKC ”T”

adapter (see Accessories in User Manual).

6.4 Wire feed pressure

Start by making sure that the wire moves smoothly through the wire guide. Then

set the pressure of the wire feeder pressure roller(s). It is important that the

pressure is not too great.

Fig 1 Fig 2

To check that the feed pressure is set correctly, you can feed out the wire against

an insulated object, e.g. a piece of wood.

When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feed

roller(s) should slip.

If you hold the gun approx. 50 mm from the piece of wood, the wire should be

fed out and bend (fig. 2).

Tabla de contenidos

Idiomas:

Otros manuales de Sistema de soldadura de ESAB

ESAB

ESAB CaddyArc 150 Manual de usuario

ESAB

ESAB PowerCut 400 Manual de usuario

ESAB

ESAB AristoFeed 30 Manual de usuario

ESAB

ESAB ET 180iP Manual de usuario

ESAB

ESAB HandyPlasma 550 Guía de configuración

ESAB

ESAB ARC250i Manual de usuario

ESAB

ESAB Aristo Mig 5000i 400 V Manual de usuario

ESAB

ESAB ST-21M Manual de usuario

ESAB

ESAB AristoMig 500 Manual de usuario

ESAB

ESAB POWERCUT-1500 Manual de usuario

ESAB

ESAB Buddy Feed 402 Manual de usuario

ESAB

ESAB Origo Mig C151 Manual de usuario

ESAB

ESAB EMP 215ic Manual de usuario

ESAB

ESAB Aristo MechTig 3000i Manual de usuario

ESAB

ESAB Precision Plasmarc IEFC-S PT-24 Instrucciones generales

ESAB

ESAB OrigoArc 200 Manual de usuario

ESAB

ESAB Migmaster 275 Manual de usuario

ESAB

ESAB Origo Mig C141 Manual de usuario

ESAB

ESAB Multimaster-260 Manual del propietario

ESAB

ESAB Cigweld EasyWeld 160 Manual de usuario

ESAB

ESAB LTR 160 Manual de usuario

ESAB

ESAB Mig 5XL Mongoose Manual de usuario

ESAB

ESAB Aristo W82 Manual de usuario

ESAB

ESAB LKA 180 Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario

ESAB migmaster 215 pro Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas