ESAB Caddy Arc 151i VRD Manual de usuario
Caddy®
Instruction manual
0460 825 374 GB 20190617 Valid for: serial no. 840-xxx-xxxx
Arc 151i VRD
TABLE OF CONTENTS
0460 825 374 © ESAB AB 2019
1SAFETY ....................................................................................................... 4
1.1 Meaning of symbols ............................................................................... 4
1.2 Safety precautions ................................................................................. 4
2INTRODUCTION.......................................................................................... 7
2.1 Equipment ............................................................................................... 7
3TECHNICAL DATA ...................................................................................... 8
4INSTALLATION............................................................................................ 10
4.1 Location................................................................................................... 10
4.2 Mains power supply ............................................................................... 10
4.2.1 Recommended fuse sizes and minimum cable area............................ 10
5OPERATION ................................................................................................ 11
5.1 PFC - Power factor correction............................................................... 11
5.2 Connections and control devices ......................................................... 11
5.3 Connection of welding and return cable .............................................. 11
5.4 Overheating protection .......................................................................... 11
5.5 MMA welding........................................................................................... 12
5.6 TIG welding ............................................................................................. 12
5.7 Remote control unit................................................................................ 13
6MAINTENANCE........................................................................................... 14
6.1 Inspection and cleaning......................................................................... 14
7TROUBLESHOOTING ................................................................................. 15
7.1 Fault codes.............................................................................................. 15
8ORDERING SPARE PARTS ........................................................................ 16
DIAGRAM ............................................................................................................ 17
ORDERING NUMBERS....................................................................................... 19
ACCESSORIES ................................................................................................... 20
Rights reserved to alter specifications without notice.
1 SAFETY
0460 825 374 -4- © ESAB AB 2019
1 SAFETY
1.1 Meaning of symbols
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Before use, read and understand the instruction manual
and follow all labels, employer´s safety practices and
Safety Data Sheets (SDSs).
1.2 Safety precautions
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
2. The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment
when it is started up
○ no-one is unprotected when the arc is struck or work is started with the
equipment
3. The workplace must:
○ be suitable for the purpose
○ be free from drafts
1 SAFETY
0460 825 374 -5- © ESAB AB 2019
4. Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns
5. General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at
hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting.
ELECTRIC SHOCK - Can kill
• Install and ground the unit in accordance with instruction manual.
• Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing.
• Insulate yourself from work and ground.
• Ensure your working position is safe
ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health
• Welders having pacemakers should consult their physician before welding.
EMF may interfere with some pacemakers.
• Exposure to EMF may have other health effects which are unknown.
• Welders should use the following procedures to minimize exposure to
EMF:
○ Route the electrode and work cables together on the same side of
your body. Secure them with tape when possible. Do not place your
body between the torch and work cables. Never coil the torch or work
cable around your body. Keep welding power source and cables as
far away from your body as possible.
○ Connect the work cable to the workpiece as close as possible to the
area being welded.
FUMES AND GASES - Can be dangerous to health
• Keep your head out of the fumes.
• Use ventilation, extraction at the arc, or both, to take fumes and gases
away from your breathing zone and the general area.
ARC RAYS - Can injure eyes and burn skin
• Protect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing.
• Protect bystanders with suitable screens or curtains.
NOISE - Excessive noise can damage hearing
Protect your ears. Use earmuffs or other hearing protection.
1 SAFETY
0460 825 374 -6- © ESAB AB 2019
MOVING PARTS - Can cause injuries
• Keep all doors, panels and covers closed and securely in place. Have only
qualified people remove covers for maintenance and troubleshooting as
necessary. Reinstall panels or covers and close doors when service is
finished and before starting engine.
• Stop engine before installing or connecting unit.
• Keep hands, hair, loose clothing and tools away from moving parts.
FIRE HAZARD
• Sparks (spatter) can cause fire. Make sure that there are no inflammable
materials nearby.
• Do not use on closed containers.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
CAUTION!
This product is solely intended for arc welding.
WARNING!
Do not use the power source for thawing frozen pipes.
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be
potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations,
due to conducted as well as radiated disturbances.
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2012/19/EC on
Waste Electrical and Electronic Equipment and its
implementation in accordance with national law,
electrical and/or electronic equipment that has reached
the end of its life must be disposed of at a recycling
facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved
collection stations.
For further information contact the nearest ESAB dealer.
ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information contact your local ESAB dealer or visit us on
our website.
2 INTRODUCTION
0460 825 374 -7- © ESAB AB 2019
2 INTRODUCTION
Arc 151i is a welding current power source intended for use with coated electrodes (MMA
welding) and TIG welding.
ESAB accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.
2.1 Equipment
Arc 151i is supplied with a 3 m welding cable, return cable, 3 m mains cable and an
instruction manual for power source and control panel.
Control panel A33
Welding process parameters are controlled via the control panel.
NOTE!
See the separate instruction manual for a detailed description of the control panel.
3 TECHNICAL DATA
0460 825 374 -8- © ESAB AB 2019
3 TECHNICAL DATA
Arc 151i
Mains voltage 230V, 1~ 50/60Hz
Primary current
Imax TIG 14A
Imax MMA 22A
Mains supply Zmax 0.35 ohm
No-load power 30W
Setting range, MMA 4 A - 150 A
Setting range, TIG 3 A - 150 A
Permissible load at MMA
25% duty cycle 150 A / 26.0 V
60% duty cycle 100 A / 24.0 V
100% duty cycle 90 A / 23.6 V
Permissible load at TIG
20% duty cycle -
25% duty cycle 150 A / 16.0 V
60% duty cycle 120 A / 14.8 V
100% duty cycle 110 A / 14.4 V
Power factor at maximum current
MMA 0.99
TIG 0.98
Efficiency at maximum current
MMA 80%
TIG 77%
Open-circuit voltage MMA/TIG 55 - 60 V
with VRD < 35V
Operating temperature -10 °C - +40°C
Transportation temperature -20 °C - +55°C
Constant A-weighted sound pressure < 70dB
Dimensions, l x b x h 418×188×208mm
Weight 8.1 kg
Enclosure class IP23
Application class
Mains supply, Zmax
Maximum permissible line impedance of the network in accordance with IEC 61000-3-11.
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or
cut at a certain load without overloading. The duty cycle is valid for 40°C/104°F, or below.
3 TECHNICAL DATA
0460 825 374 -9- © ESAB AB 2019
Enclosure class
The IP code indicates the enclosure class, i.e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP23 is intended for indoor and outdoor use.
Application class
The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.
4 INSTALLATION
0460 825 374 - 10 - © ESAB AB 2019
4 INSTALLATION
The installation must be carried out by a professional.
NOTE!
Mains supply requirements
This equipment complies with IEC 61000-3-12 provided that the short-circuit power
is greater than or equal to Sscmin at the interface point between the user's supply
and the public system. It is the responsibility of the installer or user of the equipment
to ensure, by consultation with the distribution network operator if necessary, that
the equipment is connected only to a supply with a short-circuit power greater than
or equal to Sscmin. Refer to the technical data in the TECHNICAL DATA chapter.
4.1 Location
Position the power source such that its cooling air inlets and outlets are not obstructed.
4.2 Mains power supply
Check that the welding power source is connected
to the correct voltage and that the correct fuse size
is used. A protective earth connection must be
made in accordance with regulations.
Location of rating plate
4.2.1 Recommended fuse sizes and minimum cable area
Arc 151i
Mains voltage 230 V ±10%, 1-phase
Mains frequency 50-60 Hz
Mains cable, area 3G2.5 mm2
Phase current I1eff 11 A
Welding cable, area 16 mm2
Fuse
anti-surge 16 A
type C MCB 13 A
NOTE!
The mains cable areas and fuse sizes as shown above are in accordance with
Swedish regulations. For other regions, supply cables must be suitable for the
application and meet local and national regulations.
Otros manuales para Caddy Arc 151i VRD
1
Tabla de contenidos
Otros manuales de Sistema de soldadura de ESAB
ESAB
ESAB ARC250i Manual de usuario
ESAB
ESAB CIGWELD WeldSkill 205AC/DC Manual de usuario
ESAB
ESAB Origo Mig 410 Manual de usuario
ESAB
ESAB Cutmaster 80 Manual de usuario
ESAB
ESAB ES 150i Manual de usuario
ESAB
ESAB Cigweld EasyWeld 160 Manual de usuario
ESAB
ESAB POWERCUT-1500 Manual de usuario
ESAB
ESAB Multimaster 260 Manual de usuario
ESAB
ESAB Rogue ES 180i Pro Manual de usuario
ESAB
ESAB AristoMig 4004i Pulse Manual de usuario
ESAB
ESAB PCM-1125 Manual de usuario
ESAB
ESAB PLASMAWELD 202 Manual de usuario
ESAB
ESAB MobileFeed 201 AVS Manual de usuario
ESAB
ESAB Origo Arc 256 Guía
ESAB
ESAB Rogue EM 190 PRO Manual de usuario
ESAB
ESAB Precision Plasmarc EPP-600 Manual de usuario
ESAB
ESAB HandyPlasma 250 Manual de usuario
ESAB
ESAB A2SF J1 Manual de usuario
ESAB
ESAB Caddy Mig C160i Manual de usuario
ESAB
ESAB MECHTIG 160 Manual de usuario
Manuales populares de Sistema de soldadura de otras marcas
TAFA
TAFA 30*8B35 Manual de usuario
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manual de usuario
CIGWELD
CIGWELD 636804 Guía rápida
Red-D-Arc
Red-D-Arc DC-400 Manual de usuario
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario
Elettro
Elettro HI-MIG 3000 SYNERGIC Manual de usuario
